Skip Headers
Oracle® Database Gateway for IMS, VSAM, and Adabas Installation and Configuration Guide
11g Release 1 (11.1) for Microsoft Windows

B32525-01
Go to Documentation Home
Home
Go to Book List
Book List
Go to Table of Contents
Contents
Go to Index
Index
Go to Master Index
Master Index
Go to Feedback page
Contact Us

Go to previous page
Previous
Go to next page
Next
PDF · Mobi · ePub

A Using Response Files Non-Interactive Installation

This appendix describes how to install and configure Oracle products response files. It includes the following topics:

A.1 Introduction

Typically, Oracle Universal Installer runs in interactive mode, which means that it prompts you to provide information in graphical user interface (GUI) screens. Alternatively, you can run Oracle Universal Installer in noninteractive mode. Noninteractive mode is also referred to as silent mode, or silent installation.You may want to use noninteractive mode to install Oracle Database Gateway on Microsoft Windows (32-bit) in the following scenarios:

This section covers the following topics on how you can use response files to run Oracle Universal Installer in noninteractive mode.

A.2 Using Response Files to Install Oracle Components in Non-Interactive Mode

To use noninteractive mode, you run Oracle Universal Installer with a response file. A response file is a text file that contains variables and values that Oracle Universal Installer uses during the installation process. Oracle provides a set of sample response files that you can customize, or you can create your own response file by recording your installation selections.

See Also:

Oracle Universal Installer and OPatch User's Guide for more information about response file formats.

A.3 Customizing a Sample Response File

Oracle provides response file templates for each product and installation type, and for each configuration tool. The response files for Oracle Gateway are located in the response directory on the media.

Note:

If you copied the software to a hard disk, then the response files are located in the Disk1\response directory.

To copy and modify a response file:

A.4 Creating a New Response File

When you run Oracle Universal Installer in interactive mode, you can record your installation selections into a response file. You do this by running Oracle Universal Installer in Record mode. Oracle Universal Installer generates the response file immediately after you complete the Summary page, so you do not need to actually install the gateway to create the response file.

If you want to use the Record mode during a noninteractive installation, then Oracle Universal Installer records the variable values that were specified in the original source response file into the new response file.

Note:

You cannot use Record mode to create a response file based on the Basic installation type.

To create a new response file:

  1. Make sure that the computer on which you are creating the response file has met the requirements described in respective gateway installation chapters.

  2. At the command prompt, use the cd command to change to the directory that contains the Oracle Universal Installer setup.exe executable.

    On the installation media, setup.exe is located on Disk 1. If you want to run Oracle Universal Installer from an existing gateway installation, then you can find setup.exe in ORACLE_BASE\ORACLE_HOME\oui\bin.

  3. Enter the following command:

    setup -record -destinationFile response_file_name
    

    Replace response_file_name with the complete path for the new response file. For example:

    setup -record -destinationFile C:\response_files\install_oracle10g
    
  4. After Oracle Universal Installer launches, enter the installation settings, which will be recorded into the response file.

  5. When the Summary page appears, do one of the following:

    • Click Install to continue with the installation.

    • Click Cancel if you want to only create the response file but not continue with the installation. The installation will stop, but the settings you have entered will be recorded to the response file.

    Later, Oracle Universal Installer will save your new response file using the path and file name you specified on the command line.

  6. If necessary, make any environment-specific changes to the response file for the computer on which you will run it.

  7. Run the response file by following the instructions in the Running Oracle Universal Installer and Specifying a Response File section.

A.5 Running Oracle Universal Installer and Specifying a Response File

You run Oracle Universal Installer at the command line, specifying a response file. The Oracle Universal Installer executable, setup.exe, provides several options. For help information on the full set of these options, run setup.exe with the -help option, for example:

C:\ORACLE_BASE\ORACLE_HOME\oui\bin> setup.exe -help

To run the Oracle Universal Installer and specify a response file:

  1. Start a command prompt.

  2. Go to the directory where Oracle Universal Installer is installed.

  3. From the command line, run Oracle Universal Installer with the correct response file. For example:

    C:\ORACLE_BASE\ORACLE_HOME\oui\bin> setup.exe [-silent] [-nowelcome] [-nowait] -responseFile filename
    
    Where... Description
    filename Identifies the full path of the response file
    -silent Runs Oracle Universal Installer in silent mode and suppresses the Welcome screen. If you use -silent, then -nowelcome is not necessary.
    -nowelcome Suppresses the Welcome screen that appears during installation.
    -nowait Closes the console window when the silent installation completes

    See Also:

    • Installing Oracle Products in Oracle Universal Installer and OPatch User's Guide for more information about installation using response files

    • Deinstalling Products in Oracle Universal Installer and OPatch User's Guide for more information about removing software using response files