Skip navigation.

CMDTUX Messages 4400-4499

  Previous Next

4400

INFO: Waiting up to seconds seconds for port to clear

Description

On some platforms the a TCP port may be help for up to four minutes by the operating system after use. The BRIDGE process will try to establish a port for ninety seconds before giving up completely. This message will print out every fifteen seconds with the amount of time which the BRIDGE process will wait for a hung port.

Action

Ensure that the TCP port number being used by the BRIDGE is not in use by some other process. On some operating systems, the netstat command can be used to determine the state of TCP ports.

4401

ERROR: Could not establish network descriptor for address

Description

The BRIDGE could not allocate memory for a network descriptor.

Action

The BRIDGE ran out of memory when attempting to contact address. Make sure enough memory exists on the system running the BRIDGE. If it appears that there should be enough memory to run the BRIDGE, and this error happens consistently, contact BEA Customer Support.

4402

ERROR: Could not change state of network descriptor for address

Description

An operating system error occurred while attempting to change the state of the network descriptor from non-blocking to blocking.

Action

If this error happens consistently, contact BEA Customer Support.

4403

ERROR: Could not change state of network descriptor for address

Description

An operating system error occurred while attempting to change the state of the network descriptor from blocking to non-blocking.

Action

If this error happens consistently, contact BEA Customer Support.

4404

WARN: Could not reroute encrypted messages

Description

Link level or SSL encryption was used on a network link which has gone bad. Since the message to be sent was encrypted, it cannot be recovered and sent to an alternate address.

Action

No action necessary.

4405

ERROR: NETGRPNO value value must be >= 0 and < highval

Description

While compiling the UBBCONFIG file an error occurred. NETGRPNO numbers must be between 0 and highval.

Action

Change the NETGRPNO value to be within the required range.

4406

ERROR: Memory allocation error

Description

An attempt dynamically to allocate memory from the operating system using calloc() failed while trying to allocate space for an network descriptor in the BRIDGE.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4407

ERROR: Invalid state change

Description

The administrator attempted to change the state of the BRIDGE from ACTIVE to PENDING or from PENDING to ACTIVE.

Action

These MIB state changes should not be attempted.

4408

ERROR: Shutting down bridge, serious polling error

Description

An operating system error occurred while attempting to poll the network descriptors.

Action

If this error happens consistently, contact BEA Customer Support.

4409

ERROR: Received message with unknown release number value

Description

The bridge received a packet with an unknown release number value. The network may be having difficulty. If encryption is in use, this error may be an indication that an attack is in progress.

Action

If this error happens consistently, contact BEA Customer Support.

4410

ERROR: Error decoding BRIDGE RPC msg

Description

The BRIDGE has messages which are used to synchronize communications. One of these messages has been received from another BRIDGE, but the format is unknown.

Action

If this error happens consistently, contact BEA Customer Support.

4412

ERROR: MAXPENDINGBYTES parameter must be >= 100000

Description

While compiling the UBBCONFIG file an error occurred. MAXPENDINGBYTES must be greater than or equal to 100000.

Action

Change the MAXPENDINGBYTES value to be greater than or equal to 100000.

4413

ERROR: Duplicate *NETGROUPS section

Description

While compiling the UBBCONFIG file an error occurred. There may only be one NETGROUPS section in the UBBCONFIG file.

Action

Remove duplicate NETGROUPS sections from the UBBCONFIG file.

4415

ERROR: Identifier for network group name must be <= value characters in length

Description

While compiling the UBBCONFIG file an error occurred. A network group name must be less than or equal to value characters.

Action

Shorten the name of the network group in the NETGROUPS section.

4417

ERROR: Network group name name must not contain *, comma, or colon

Description

While compiling the UBBCONFIG file an error occurred. The network group name name may not contain certain characters.

Action

Remove the undesirable characters from name.

4419

ERROR: Duplicate *NETGROUPS entry entry

Description

While compiling the UBBCONFIG file an error occurred. A duplicate network group entry was found.

Action

Network group names must be unique. Choose another name for this network group.

4420

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed during tmloadcf while trying to allocate space for the network group table.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4421

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using realloc() failed during tmloadcf while trying to allocate space for the network group table.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4422

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed during tmloadcf while trying to allocate space for the network group name.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4423

ERROR: More than MAXNETGROUPS(value) in configuration file

Description

While compiling the UBBCONFIG file an error occurred. The maximum number of network groups allowed in a configuration is controlled by the RESOURCES parameter MAXNETGROUPS. The number of netgroups found in the UBBCONFIG file is greater than the maximum number of netgroups.

Action

Either remove network groups or increase the value of MAXNETGROUPS.

4424

ERROR: Must have a NETGRPNO on *NETGROUPS entry entry

Description

While compiling the UBBCONFIG file an error occurred. NETGRPNO is a required parameter for each entry in the NETGROUPS section. entry did not supply the required parameter.

Action

Supply a network group number for the entry network group. Network group numbers must be unique, and should remain consistent for the life of the network group. The network group number is used to co-ordinate failover and failback of the network.

4425

ERROR: *NETGROUPS entry entry has a duplicate NETGRPNO parameter of value

Description

While compiling the UBBCONFIG file an error occurred. NETGRPNO is a required parameter for each entry in the NETGROUPS section, and must be unique. entry did not supply a unique NETGRPNO parameter.

Action

Supply a network group number for the entry network group. Network group numbers must be unique, and should remain consistent for the life of the network group. value is not unique. The network group number is used to co-ordinate failover and failback of the network.

4427

ERROR: NETGRPNO for the entry network group may not be 0

Description

While compiling the UBBCONFIG file an error occurred. NETGRPNO is a required parameter for each entry in the NETGROUPS section, and must be unique. There is always at least one network group named DEFAULTNET which has a NETGRPNO of zero. Hence, network group entry may not have a NETGRPNO of zero.

Action

Supply a network group number for the entry network group. Network group numbers must be unique, and should remain consistent for the life of the network group. value is not unique, since the network group DEFAULTNET has a NETGRPNO of zero. The network group number is used to coordinate failover and failback of the network.

4429

ERROR: MAXNETGROUPS parameter must be >= lowval and < highval

Description

While compiling the UBBCONFIG file an error occurred. The MAXNETGROUPS parameter must be between lowval and highval.

Action

Change the MAXNETGROUPS value to be within the required range.

4430

ERROR: RESOURCES section must appear before NETGROUPS section

Description

While compiling the UBBCONFIG file an error occurred. The NETGROUPS section must appear before the RESOURCES section.

Action

Place the NETGROUPS section after the RESOURCES section.

4432

ERROR: NETPRIO must be > 0 and <= value

Description

While compiling the UBBCONFIG file an error occurred. The network priority of a network group must be greater than zero and less than or equal to value.

Action

Change the NETPRIO parameter to be within the required range.

4433

ERROR: NETGROUPS section must appear before NETWORK section

Description

While compiling the UBBCONFIG file an error occurred. The NETGROUPS section must appear before the NETWORK section.

Action

Place the NETWORK section after the NETGROUPS section.

4434

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using calloc() failed during tmloadcf while trying to allocate space for the network map table.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4435

ERROR: Could not find machine section

Description

The BRIDGE could not find the MACHINES section of the TUXCONFIG file.

Action

The TUXCONFIG file may be corrupt. If this machine is the master node, try removing the TUXCONFIG file and regenerating it from the UBBCONFIG using tmloadcf. If this machine is a remote node, make sure that all IPC resources have been removed from the machine. Then remove the TUXCONFIG file, and attempt to tmboot the machine from the MASTER machine. If this error happens consistently, contact BEA Customer Support.

4436

ERROR: Could not find LMID name in machine section

Description

The BRIDGE could not find the LMID name in the TUXCONFIG file. The BRIDGE is searching for its own entry in the TUXCONFIG file.

Action

The TUXCONFIG file may be corrupt. If this machine is the master node, try removing the TUXCONFIG file and regenerating it from the UBBCONFIG using tmloadcf. If this machine is a remote node, make sure that all IPC resources have been removed from the machine. Then remove the TUXCONFIG file, and attempt to tmboot the machine from the MASTER machine. If this error happens consistently, contact BEA Customer Support.

4437

ERROR: Memory allocation error

Description

An attempt to dynamically allocate memory from the operating system using malloc() failed while trying to allocate space for communication with the tlisten.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine. There may be a security attack in progress.

4438

WARN: Minimum encryption (min) is larger than 0, but the link level package is not installed

Description

An attempt was made to use link level encryption of min bits on a network link. However, the link level encryption package has not been installed on this machine.

Action

Install the link level encryption package on this machine, or change the MINENCRYPTBITS value of min for this network entry to zero.

4439

ERROR: LMID name must match LMID from the *MACHINES section

Description

While compiling the UBBCONFIG file an error occurred. In the NETWORK section, each entry must match a corresponding entry in the MACHINES section. name does not match any entry in the MACHINES section.

Action

Either remove the NETWORK section entry or add a MACHINES section entry corresponding to the given LMID.

4440

ERROR: NETGROUP name must match NETGROUP from the *NETGROUPS section

Description

While compiling the UBBCONFIG file an error occurred. The NETGROUPS parameter of a NETWORK section entry must match a netgroup previously defined in the NETGROUPS section. name does not match any entry in the NETGROUPS section.

Action

Either remove the NETWORK section entry or add a NETGROUPS section entry corresponding to the given NETGROUP parameter.

4442

ERROR: Invalid group information/self NADDR missing, NETGRPNO netgrpno

Description

The BRIDGE was attempting to discover network parameters pertaining to its own set of netgroups. However, it could not find any network groups for which it is a member.

Action

Ensure that every machine in a network application is a member of a network group. All machines should be members of the DEFAULTNET group, and may also be members of any other network group.

4443

ERROR: TA_NETGROUP cannot be used on a SET operation

Description

The TA_NETGROUP field may not be set during a SET operation of the T_BRIDGE class.

Action

Remove the TA_NETGROUP field from all SET operations involving the T_BRIDGE class.

4450

ERROR: NETGRPNO for the netgroup network group must be 0

Description

While compiling the UBBCONFIG file an error occurred. The value of NETGRPNO for the netgroup network group must be zero.

Action

netgroup is a special network group which must have a NETGRPNO value of zero. Change NETGRPNO for this network group to zero.

4452

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using realloc() failed during tmloadcf while trying to allocate space for the network map table.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4453

ERROR: The combination of NETGROUP netgroup and LMID lmid must be unique

Description

While compiling the UBBCONFIG file an error occurred. No two entries in the NETWORK section may have the same LMID and NETGROUP attributes.

Action

Ensure that all entries in the NETWORK section have a unique combination of LMID and NETGROUP values. In particular, more than one lmid entry has a NETGROUP parameter of netgroup.

4455

ERROR: NETGROUP parameter must be <= value characters

Description

While compiling the UBBCONFIG file an error occurred. A network group name must be less than or equal to value characters.

Action

Shorten the name of the NETGROUP field in the NETWORK section.

4460

ERROR: BRIDGE Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed while trying to allocate space for an internal circuit table in the BRIDGE.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine. The use of MAXPENDINGBYTES in the machines section may alleviate the BRIDGE memory allocation problem.

4461

ERROR: Could not find BRIDGE NADDR address for lmid

Description

While attempting to connect to the LMID lmid, the BRIDGE process could not find an address to connect to the TUXCONFIG file.

Action

Ensure that an entry exists for lmid in the UBBCONFIG NETWORK section. If an entry exists, contact BEA Customer Support.

4462

ERROR: Could not find BRIDGE NADDR address for lmid

Description

While attempting to connect to the LMID lmid, the BRIDGE process could not find an address to connect to the TUXCONFIG file.

Action

Ensure that an entry exists for lmid in the UBBCONFIG NETWORK section. If an entry exists, contact BEA Customer Support.

4464

ERROR: Could not initialize global network information

Description

An operating system error occurred while attempting to initialize network information. The tlisten will not boot.

Action

Ensure the viability of the network. If the network appears to be viable, contact BEA Customer Support.

4465

ERROR: BRIDGE Memory allocation error

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed while trying to allocate space for an internal circuit table in the BRIDGE.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine. The use of MAXPENDINGBYTES in the machines section may alleviate the BRIDGE memory allocation problem.

4466

ERROR: BRIDGE Memory allocation error while connecting lmid

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed while the BRIDGE was connecting to lmid.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine. The use of MAXPENDINGBYTES in the machines section may alleviate the BRIDGE memory allocation problem.

4467

ERROR: BRIDGE system error at id

Description

An internal error was captured by the BRIDGE.

Action

Contact BEA Customer Support.

4468

ERROR: Could not initialize protocol specific network information

Description

An operating system error occurred while attempting to initialize network information. tlisten will not boot.

Action

Ensure the viability of the network. If the network appears to be viable, contact BEA Customer Support.

4469

ERROR: Could not initialize protocol specific network information

Description

An operating system error occurred while attempting to initialize network information. tlisten will not boot.

Action

Ensure the viability of the network. If the network appears to be viable, contact BEA Customer Support.

4471

ERROR: Received message with unknown release number value

Description

The tlisten received a packet with an unknown release number value. The network may be having difficulty. If link level encryption is in use, this error may be an indication that an attack is in progress.

Action

If this error happens consistently, contact BEA Customer Support.

4472

ERROR: Could not allocate network resource

Description

A network descriptor could not be allocated for the listening endpoint in tlisten.

Action

Ensure the network on the system is viable. If this error happens consistently, contact BEA Customer Support.

4473

ERROR: Unable to decrypt message

Description

A process speaking to a tlisten process could not decrypt one of the messages coming from the tlisten. This error may indicate that an attack is in progress.

Action

Ensure the network on the system is viable. If this error happens consistently, contact BEA Customer Support.

4474

ERROR: Error encrypting buffer for TAGENT on lmid

Description

A process speaking to a tlisten process could not encrypt a message for the tlisten on lmid. This error may indicate that an attack is in progress.

Action

Ensure the network on the system is viable. If this error happens consistently, contact BEA Customer Support.

4475

INFO: SRVID = id SRVGRP = grp SIGTERM send failed (tperrno = tperrno)

Description

tmshutdown was unable to send a SIGTERM to a server of the given id and grp. The value of tperrno may provide further information on the source of the failure.

Action

No action necessary.

4476

INFO: SRVID = id SRVGRP = grp SIGKILL send failed (tperrno = tperrno)

Description

tmshutdown was unable to send a SIGKILL to a server of the given id and grp. The value of tperrno may provide further information on the source of the failure.

Action

No action necessary.

4477

INFO: SRVID=id SRVGRP=grp SIGTERM send failed (tperrno=tperrno)

Description

tmshutdown was unable to send a SIGTERM to a server of the given id and grp. The value of tperrno may provide further information on the source of the failure.

Action

No action necessary.

4478

INFO: SRVID=id SRVGRP=grp SIGKILL send failed (tperrno=tperrno)

Description

tmshutdown was unable to send a SIGKILL to a server of the given id and grp. The value of tperrno may provide further information on the source of the failure.

Action

No action necessary.

4479

ERROR: Could not get encryption handle

Description

tlisten could not get a resource necessary to perform encryption.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4480

ERROR: NETGROUP id negotiation failed with bridge on lmid

Description

The NETGRPNO of a the remote lmid machine does not match the value given in the local version of the TUXCONFIG file. This error may indicate that a security attack was in progress.

Action

Ensure the network is viable and that there were no security attacks in progress. It may be necessary to bring the affected machine down, remove its TUXCONFIG file and tmboot the machine.

4482

ERROR: .SysServiceTimeout: queue, group group, id srvid server killed due to a service time-out

Description

The BBL has killed a server due to a service time-out. The server is described by its queue, group and srvid.

Action

The administrator may need to configure the service time-out higher in order to accommodate a heavily loaded system.

4483

INFO: .SysMachineState: mid state change to ACTIVE

Description

The given mid has become unpartitioned.

Action

No action necessary.

4484

INFO: .SysMachineUnpartitioned: mid is unpartitioned

Description

The given mid has become unpartitioned.

Action

No action necessary.

4485

INFO: .SysMachineState: mid state change to ACTIVE

Description

The given mid has become unpartitioned.

Action

No action necessary.

4486

ERROR: Could not send saved messages

Description

The BRIDGE process saves messages while an asynchronous connect is outstanding. However, once the connection was established, there was an error sending the messages saved for the remote machine.

Action

Ensure that the network connection is viable. If the network is flaky, it is possible that the connection establishment packet was received, but that subsequent packets were lost by the network. If the network appear to be viable, contact BEA Customer Support.

4487

ERROR: BRIDGE did not generate a unique circuit ID

Description

The BRIDGE tried to generate a unique circuit identifier and the algorithm failed to do so.

Action

Contact BEA Customer Support.

4488

INFO: Connecting to pmid at address

Description

This is an information message that indicates that a connection is being made to a machine at the specified address.

Action

No action required.

4489

ERROR: BRIDGE Memory allocation error

Description

The BRIDGE failed to allocate memory.

Action

Make sure that the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory on the machine.

4490

ERROR: Connection failure to machine at address

Description

The BRIDGE process could not connect to machine.

Action


4491

ERROR: Could not send saved messages to site

Description

While the BRIDGE or BSBRIDGE is negotiating encryption parameters or when flow control exists on the network link, messages to the remote BRIDGE are saved. An error occurred while sending these saved messages to the remote BRIDGE after the negotiation was complete or the flow control condition eased.

Action

Check the network on the machine with the affected BRIDGE or BSBRIDGE.

4492

INFO: Resuming BRIDGE failover/failback messages

Description

There had been too many BRIDGE reconnection attempt LOG messages sent. Enough time has passed, so messages should be logged once more.

Action

This is an informational message, no action is required. If the connection is not established, notify the network administrator of the network outage.

4493

INFO: Temporarily suppressing BRIDGE failover/failback messages

Description

The BRIDGE has been sending many messages to the log file while trying to re-establish communications on various network addresses. The loop is sending too many messages to the LOG, so though the actions are continuing, they are not being logged.

Action

The BRIDGE is silently trying to reconnect, the actions are not being logged. The network administrator should work to restore network connectivity since there is an outage. Once sufficient time has passed, more of these messages may be logged if the network connections still fail.

4494

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed while trying to allocate a message in the BBL to send a process obituary during a pclean operation.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.

4495

ERROR: Tuxedo typed buffer routine failed

Description

An attempt to create a message in the BBL to send a process obituary failed for a reason other than allocating memory.

Action

Review other messages earlier in the log that indicate what caused the failure.

4497

ERROR: Unknown message header

Description

While a secondary Event Broker was receiving the event database from the primary Event Broker, processing the message failed.

Action

Contact BEA Customer Support.

4498

ERROR: Memory allocation failure

Description

An attempt dynamically to allocate memory from the operating system using malloc() failed while trying to allocate a message in the BBL to send a process obituary.

Action

Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.

4499

ERROR: Tuxedo typed buffer routine failed

Description

An attempt to create a message in the BBL to send a process obituary failed for a reason other than allocating memory.

Action

Review other messages earlier in the log that indicate what caused the failure.

 

Skip footer navigation  Back to Top Previous Next