| Sun Blade X6250 Server Module Service Manual |     |
Sun Blade X6250 Server Module Service Manual
820-1185-17
|
Contents |
1. Introduction to the Sun Blade X6250 Server Module
1.2 Sun Blade X6250 Server Module Orientation
1.2.1 Server Module Front Panel
1.2.2 Server Module Components
1.3 Using a Dongle Cable for Testing
To Use a Dongle Cable for Testing
1.5 Additional Options and Replaceable Components
1.6 Customer Replaceable Units (CRUs) and Field Replaceable Units (FRUs)
2. Powering On and Configuring BIOS Settings
2.3.1 Changing the Configuration of a BIOS Menu Item
2.3.2.1 PCI Card Slot Booting Priority
2.3.2.2 Ethernet Port Device and Driver Naming
2.3.2.3 Ethernet Port (NIC) Booting Priority
2.3.2.4 BIOS Option ROM Size Limitation
2.3.3 Descriptions of the BIOS Setup Utility Screens
2.3.4 BIOS Setup Utility Menu Screens
2.3.4.8 Super I/O Confriguration
2.3.4.13 Event Log Configuration
2.3.4.19 AST2000 LAN Configuration
2.3.4.23 Remote Access Configuration
2.4 Resetting the BIOS Password and Clearing CMOS
2.5 Resetting the Service Processor Password Using the BIOS Setup Utility
To Reset the SP Password Using the BIOS Setup Utility
3.1 Monitoring System Components
3.1.1 Monitoring System Components Through the Service Processor
3.1.2 Monitoring System Components Through System Status LED
3.1.2.1 External Status Indicator LEDs
3.1.2.2 Internal Status Indicator LEDs
3.3 Removing the Server Module From the Chassis and Removing the Cover
3.3.1 Removing the Server Module From the Chassis
3.4 Locations of Replaceable Components
3.5 Replaceable Component Procedures
3.5.1 Replacing the Coin Battery
3.5.2 Replacing the Compact Flash Module
To Replace the Compact Flash Module
3.5.3 Replacing Memory Modules (DIMMs)
3.5.3.2 Error Correction and Parity
3.5.4 Replacing a CPU and Heatsink
3.5.5 Replacing the Motherboard
3.5.6.2 Solid State Drives (SSDs)
3.5.6.3 HD Replacement Procedure
3.5.7 Adding or Replacing a RAID Expansion Module
To Add, Remove or Replace a REM Board
3.5.8 Restoring an Existing RAID Array After Changing the REM
To Restore a RAID Array After Replacing a REM Card
3.5.9 Changing the Sun Blade RAID 5 Expansion Module Battery
3.5.10 Replacing a Fabric Expansion Module
To Install Fabric Expansion Module
To Remove a Fabric Expansion Module
4. Performing Diagnostic Tests
4.1 Pc-Check Diagnostics Overview
To Access the Pc-Check Diagnostics
To Select and Test a Hard Disk
4.5.1 Performing Immediate Burn-In Testing
To Perform Immediate Burn-in Testing
4.5.2 Performing Deferred Burn-In Testing
To Perform Deferred Burn-in Testing
5.1 Updating BIOS, CPLD and the SP
To Update BIOS, CPLD and the SP
To Update CPLD (Common Programmable Logic Device) on the Motherboard
To Update the REM Firmware from a DOS-Bootable USB Thumb Drive
A.1 Server Module Specifications
B. BIOS Power-On Self-Test (POST) Codes
B.2 How BIOS POST Memory Testing Works
B.3 Redirecting Console Output
| Sun Blade X6250 Server Module Service Manual | 820-1185-17 | |
Copyright © 2009 Sun Microsystems, Inc. All rights reserved.