Administering SRDF Application Resource Groups

To make an application highly available, the application must be managed as a resource in an application resource group.

All the entities you configure for the application resource group on the primary cluster, such as resources and the application resource group, must be replicated to the secondary cluster. The resource group names must be identical on both clusters. Also, the data that the application resource uses must be replicated to the secondary cluster.

This section contains information about the following tasks:

• How to Add an Application Resource Group to an SRDF Protection Group

• How to Delete an Application Resource Group From an SRDF Protection Group

How to Add an Application Resource Group to an SRDF Protection Group

Before You Begin

You can add an existing resource group to the list of application resource groups for a protection group. Before you add an application resource group to a protection group, ensure that the following conditions are met:

• The protection group is defined.

• The resource group exists on both clusters and is in an appropriate state.

• The Auto_start_on_new_cluster property of the resource group is set to False. You can view this property by using the clresourcegroup command.

  # clresourcegroup show -p auto_start_on_new_cluster apprg

  When you bring a protection group online on the primary cluster, bring the application resources groups that participate in that protection group online only on the same primary cluster. Setting the Auto_start_on_new_cluster property to False prevents the Oracle Solaris Cluster resource group manager from automatically starting the application resource groups. In this case, the startup of resource groups is reserved for the Geographic Edition software.

  Application resource groups should be online only on primary cluster when the protection group is activated.

  Set the Auto_start_on_new_cluster property to False as follows:

  # clresourcegroup set -p Auto_start_on_new_cluster=False apprg1

• The application resource group must not have dependencies on resource groups and resources outside of this protection group. To add several application resource groups that share dependencies, you must add the application resource groups to the protection group in a single operation. If you add the application resource groups separately, the operation fails.

• The HAStoragePlus resource must exist in the application resource group, so that it can bring online the devices and mount the file systems.

The protection group can be activated or deactivated and the resource group can be either Online or Offline.

If the resource group is Offline and the protection group is Active after the configuration of the protection group has changed, the local state of the protection group becomes Degraded.

If the resource group to add is Online and the protection group is deactivated, the request is rejected. You must activate the protection group before adding an activate resource group.

1. Log in to a cluster node.

   You must be assigned the Geo Management RBAC rights profile to complete this procedure. For more information about RBAC, see Geographic Edition Software and RBAC in Oracle Solaris Cluster Geographic Edition System Administration Guide.

2. Add an application resource group to the protection group.

   This command adds an application resource group to a protection group on the local cluster. Then the command propagates the new configuration information to the partner cluster if the partner cluster contains a protection group of the same name.

   # geopg add-resource-group resourcegrouplist protectiongroup

   resourcegrouplist

   Specifies the name or names of the application resource group.

   You can specify more than one resource group in a comma-separated list.

   protectiongroup

   Specifies the name of the protection group.

   For information about the names and values that are supported by Geographic Edition software, see Appendix B, Legal Names and Values of Geographic Edition Entities, in Oracle Solaris Cluster Geographic Edition System Administration Guide.

   If the add operation is unsuccessful on the local cluster, the configuration of the protection group is not modified. Otherwise, the Configuration status is set to OK on the local cluster.

   If the application resource group configuration is OK on the local cluster, the application resource group gets added to the protection group on the local and remote cluster. If the subsequent configuration validation on the remote cluster does not result in a status of OK on the partner, the status is set to Error on the partner cluster.

   After the application resource group is added to the protection group, the application resource group is managed as an entity of the protection group. Then the application resource group is affected by protection group operations such as start, stop, switchover, and takeover.

Example 2-8 Adding an Application Resource Group to a Protection Group

This example adds two application resource groups, apprg1 and apprg2, to srdfpg.

# geopg add-resource-group apprg1,apprg2 srdfpg

How to Delete an Application Resource Group From an SRDF Protection Group

You can remove an application resource group from a protection group without altering the state or contents of an application resource group.

Before You Begin

Ensure that the following conditions are met:

• The protection group is defined on the local cluster.

• The resource group to be removed is part of the application resource groups of the protection group.

1. Log in to a cluster node.

   You must be assigned the Geo Management RBAC rights profile to complete this procedure. For more information about RBAC, see Geographic Edition Software and RBAC in Oracle Solaris Cluster Geographic Edition System Administration Guide.

2. Remove the application resource group from the protection group.

   This command removes an application resource group from the protection group on the local cluster. If the partner cluster contains a protection group of the same name, then the command removes the application resource group from the protection group on the partner cluster.

   If resource groups in the protection group have dependencies between them, you must remove all affected resource groups in the same geopg remove-resource-groupcommand.

   # geopg remove-resource-group resourcegrouplist protectiongroup

   resourcegrouplist

   Specifies the list of application resource groups.

   You can specify more than one resource group in a comma-separated list.

   protectiongroup

   Specifies the name of the protection group.

   If the remove operation is unsuccessful on the local cluster, the configuration of the protection group is not modified. Otherwise, the Configuration status is set to OK on the local cluster.

   If the Configuration status is OK on the local cluster, but the remove operation is unsuccessful on the partner cluster, the Configuration status is set to Error on the partner cluster.

Example 2-9 Deleting an Application Resource Group From a Protection Group

This example removes two application resource groups, apprg1 and apprg2, from srdfpg.

# geopg remove-resource-group apprg1,apprg2 srdfpg