Sun Netra CP3250 Blade Server Sensor Map and Fault Isolation

A P P E N D I X I

This appendix defines the sensors for the Sun Netra CP3250 blade server.

Sun Netra CP3250 Blade Server Sensor List

The sensor numbers and names are reported by the on-blade server Sun Netra CP3250 IPMC processor via the ShMM, within the ATCA chassis.

TABLE I-1 Sun Netra CP3250 Blade Server Sensor List
Sensor Number	Sensor Name	Sensor Type	Sensor Description	Fault Condition if Sensor Out of Limit
0	FRU 0 Hot Swap	Discrete (0x6f), "Hot Swap" (0xf0)	Hot swap for CP3250 FRU	N/A
1	HotSwap AMC 5	Discrete (0x6f), "Hot Swap" (0xf0)	Hot swap for AMC FRU	N/A
2	HotSwap ARTM 15	Discrete (0x6f), "Hot Swap" (0xf0)	Hot swap for ARTM FRU	N/A
3	IPMB Physical	Discrete (0x6f), "Hot Swap" (0xf0)	Link Status of IPMB	No reply from IPMB (A or B). State of IPMB A or B bus is reported by monitoring the READY signal on the IPMB isolator.
4	BMC Watchdog	Discrete (0x6f), "Watchdog 2" (0x23)	Watchdog state of BMC	N/A
5	12.0V	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 12.0V power rail	If this voltage is out of spec or goes to zero, all other power rails will fail (Except STBY). Blade server and the RTM will not function. The IPMC will be alive if 3.3V STBY is up. Supplies: All DC/DC converters
6	5.0V	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 5.0V power rail	If this voltage is out of spec or goes to zero, most other power rails will fail. Blade server will not function. The IPMC will be alive if 3.3V STBY is up. Supplies: Most DC/DC converters
7	3.3V	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 3.3V power rail	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. The IPMC will be alive if 3.3V STBY is up. Supplies: Multiple support devices
8	3.3V STBY	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 3.3V STBY power rail.	If this voltage is out of spec blade server and the H8 will not function. This rail is the power source for the management components on the blade server including all I2C devices and the H8.
9	SuperCAP voltage	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 3.0V battery (ADM 1026, pin 29)	If this voltageis out of limit, the battery has failed or is not installed. Ignore message if not using the battery.
10	1.2V NTune	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 1.2V power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function.
11	CPU VTT	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of the VTT power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function.
12	1.5V	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 1.5V power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. The IPMC will be alive if 3.3V STBY is up. Supplies: CPU I/O, DIMMs
13	1.8 V	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 1.8V power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function.
14	DDR2 VTT	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of DDR VTT power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. Devices: DIMMs
15	1.05 V Core	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 1.05V power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. Devices: CPU
16	1.5 V NTune	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of 1.5V power rail.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. Devices: Neptune
17	VCC CPU1	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of VCC CPU.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. Devices: CPU
18	VCC CPU0	Threshold (0x01), "Voltage" (0x02)	Voltage measurement of VCC CPU.	If this voltage is out of spec or goes to zero, many components on blade server will not function. Therefore, blade server will not function. Devices: CPU
19	Inlet 1 Temp Sen	Threshold (0x01), "Temperature" (0x01)	Ambient Temp, unused	N/A. To be deleted in future release.
20	Inlet 3 Temp Sen	Threshold (0x01), "Temperature" (0x01)	Ambient Temp, unused	N/A. To be deleted in future release.
21	Inlet 2 Temp Sen	Threshold (0x01), "Temperature" (0x01)	Ambient Temp, unused	N/A. To be deleted in future release.
22	MCH Temp Sensor	Threshold (0x01), "Temperature" (0x01)	Junction Temperature, Memory Controller Hub, Northbridge	This sensor indicates that the MCH is out of temperature range.
23	CPU_TEMP_SK0D0	Threshold (0x01), "Temperature" (0x01)	CPU Junction Temp, socket 0, domain 0	This sensor indicates that the CPU is out of temperature range. Above 94C will cause blade server to shutdown.
24	CPU_TEMP_SK0D1	Threshold (0x01), "Temperature" (0x01)	CPU Junction Temp, socket 0, domain 1	This sensor indicates that the CPU is out of temperature range. Above 94C will cause blade server to shutdown.
25	CPU_TEMP_SK1DO	Threshold (0x01), "Temperature" (0x01)	CPU Junction Temp, socket 1, domain 0	This sensor indicates that the CPU is out of temperature range. Above 94C will cause blade server to shutdown.
26	CPU_TEMP_SK1D1	Threshold (0x01), "Temperature" (0x01)	CPU Junction Temp, socket 1, domain 1	This sensor indicates that the CPU is out of temperature range. Above 94C will cause blade server to shutdown.
27	Version change	Discrete (0x6f), "reserved" (0x2b)	Firmware update event	Reports event after the FW update/cold reset
28	System Event	Discrete (0x6f), "System Event" (0x12)	System reset event	This sensor reports IPMC reset event to ShMM. This sensor lets NetConsole application know that IPMC has taken a reset and the NetConsole session has to be restarted.
29	CPU 0 presence	Discrete (0x6f), "Entity Presence" (0x25)		Indicates that CPU0 is installed.
30	CPU 1 presence	Discrete (0x6f), "Entity Presence" (0x25)		Indicates that CPU1 is installed.
31	P48V Alarm	Discrete (0x70), "OEM reserved" (0xc0)	Voltage measurement of 48V power	Detects either the 48V power input A or 48V power input B to power module that converts it to 12V.
32	Sys FW Progress	Discrete (0x6f), "System Firmware Progress" (0x0f),	Monitors the system firmware progress states.	This sensor monitors the firmware progress. The system firmware sends the firmware progress events to the system event log by way of the IPMC.
33	Graceful Reboot	Discrete (0x6f) "OEM reserved" (0xc0)	Monitors the state of aa graceful reboot.	This sensor logs events into the system event log when a graceful reboot timer starts, stops, or expires.