If you are using Solaris 10 3/05, use the procedure How To Configure Static VLANs in Solaris 10 3/05 ONLY.
Assume the Primary Administrator role, or become superuser.
The Primary Administrator role includes the Primary Administrator profile. To create the role and assign the role to a user, see Chapter 2, Working With the Solaris Management Console (Tasks), in System Administration Guide: Basic Administration.
Determine the types of interfaces in use on your system.
# dladm show-link |
The output shows the available interface types:
ce0 type: legacy mtu: 1500 device: ce0 ce1 type: legacy mtu: 1500 device: ce1 bge0 type: non-vlan mtu: 1500 device: bge0 bge1 type: non-vlan mtu: 1500 device: bge1 bge2 type: non-vlan mtu: 1500 device: bge2 |
Configure an interface as part of a VLAN.
# ifconfig interface-PPA plumb IP-address up |
For example, you would use the following command to configure the interface ce1 with a new IP address 10.0.0.2 into a VLAN with the VID 123:
# ifconfig ce123001 plumb 10.0.0.2 up |
You can assign IPv4 and IPv6 addresses to VLANs just as you do to other interfaces.
(Optional) To make the VLAN settings persist across reboots, create a hostname.interface-PPA file for each interface that is configured as part of a VLAN.
# cat hostname.interface-PPA IPv4-address |
On the switch, set VLAN tagging and VLAN ports to correspond with the VLANs that you have set up on the system.
This example shows how to configure devices bge1 and bge2 into a VLAN with the VID 123.
# dladm show-link ce0 type: legacy mtu: 1500 device: ce0 ce1 type: legacy mtu: 1500 device: ce1 bge0 type: non-vlan mtu: 1500 device: bge0 bge1 type: non-vlan mtu: 1500 device: bge1 bge2 type: non-vlan mtu: 1500 device: bge2 # ifconfig bge123001 plumb 10.0.0.1 up # ifconfig bge123002 plumb 10.0.0.2 up # cat hostname.bge123001 10.0.0.1 # cat hostname.bge123002 10.0.0.2 # ifconfig -a lo0: flags=2001000849 <UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge123001: flags=201000803<UP,BROADCAST,MULTICAST,IPv4,CoS> mtu 1500 index 2 inet 10.0.0.1 netmask ff000000 broadcast 10.255.255.255 ether 0:3:ba:7:84:5e bge123002:flags=201000803 <UP,BROADCAST,MULTICAST,IPv4,CoS> mtu 1500 index 3 inet 10.0.0.2 netmask ff000000 broadcast 10.255.255.255 ether 0:3:ba:7:84:5e ce0: flags=1000843 <UP,BROADCAST,RUNNING,MULTICAST,IPv4>mtu 1500 index 4 inet 192.168.84.253 netmask ffffff00 broadcast 192.168.84.255 ether 0:3:ba:7:84:5e # dladm show-link ce0 type: legacy mtu: 1500 device: ce0 ce1 type: legacy mtu: 1500 device: ce1 bge0 type: non-vlan mtu: 1500 device: bge0 bge1 type: non-vlan mtu: 1500 device: bge1 bge2 type: non-vlan mtu: 1500 device: bge2 bge123001 type: vlan 123 mtu: 1500 device: bge1 bge123002 type: vlan 123 mtu: 1500 device: bge2 |