Eftersom LSI Logic BIOS och Solaris fdisk-programmet kan vara inkompatibla bör du använda DOS-versionen av FDISK (eller motsvarande verktyg) för att skapa en post i FDISK-tabellen för partitionen innan du installerar Solaris-programmet. Skapa en DOS-partition som åtminstone är 1 cylinder stor, och startar på cylinder 0. Om DOS-partitionen inte skapas startar inte systemet om efter Solaris-installationen.
Ett tilläggskort med 53C815-, 53C820-, 53C825- eller 53C825A-styrenhet kan bara användas i en PCI-kortplats för huvudbusstyrning. På systemkort med endast två PCI-kortplatser kan oftast båda PCI-kortplatserna användas som huvudbussar. På systemkort med tre eller fler PCI-kortplatser, och på systemkort med flera inbäddade PCI-styrenheter, kanske inte alla PCI-kortplatser kan användas som huvudbussar.
En del PCI-systemkort med LSI Logic SDMS BIOS och en inbäddad 53C810- eller 53C810A-styrenhet fungerar inte korrekt med tilläggskorten 53C820, 53C825 och 53C825A som även de har LSI Logic SDMS BIOS. Om du uppgraderar systemkortets BIOS, tilläggskortet eller båda kan du undvika dessa konflikter.
På en del äldre PCI-system som har 53C810-kretsen på systemkortet är inte interrupt pin på kretsen ansluten. Du kan inte använda ett sådant system tillsammans med Solaris.
Anslut inte smala målenheter till den smala anslutningen på de kort som har stöd för smala skivminnen. Dessa konfigurationer stöds inte.
Om kortet stöder LSI Logics SCSI-konfigurationsverktyg, som du kan starta genom att trycka på Control+C, måste värdet för Host SCSI ID (ett alternativ på menyn Adapter Setup) vara 7.
Om det uppstår problem med äldre målenheter lägger du till följande post i filen /kernel/drv/ncrs.conf:
targetN-scsi-options = 0x0;
där N är ID:t för det felaktiga målet.
Om du använder en Conner 10805 smal SCSI-enhet kan du få varningar som påminner om följande:
WARNING: /pci@0,0/pci1000,f@d(ncrs0): invalid reselection(0,0) WARNING: /pci@0,0/pci1000,f@d/sd@0,0(sd0): SCSI transport failed: 'reset: retrying command'
Du kan få bort dessa varningar genom att inktivera tagged queuing i filen ncrs.conf. Mer information finns i direkthjälpen för ncrs( 7D).
På en del Pentium-systemkort (Intel NX-kretsar) som använder en P90-processor eller långsammare processor, låser sig ncrs och följande meddelande visas i systemfönstret:
WARNING: /pci@0,0/pci1000,3@6(ncrs0) Unexpected DMA state:active dstat=c0<DMA-FIFO-empty, master-data-parity-error>
Detta går inte att åtgärda, systemet installerar inte ncrs-drivrutinen.
ncrs-drivrutinen stöder minst version 4 av 53C875-kretsen. Tidigare utgåvor var preliminära versioner av kretsen och det kan fortfarande finnas en del i omlopp.
Om du använder en SDT7000/SDT9000-bandenhet kan följande meddelande i sällsynta fall visas i systemfönstret:
Unexpected DMA state: ACTIVE. dstat=81<DMA-FIFO-empty,illegal-instruction>
Under dessa omständigheter återhämtar systemet sig och du kan fortsätta att använda bandenheten. Du kan fortfarande använda kommandot tar för att lägga till eller extrahera filer på bandet.