Sun Blade 6000 Virtualized Multi-Fabric 10GbE M2 NEM 用户指南概述
Sun Blade 6000 Virtualized Multi-Fabric 10GbE M2 NEM 的特性
通过 Virtualized M2 NEM 10 千兆位以太网端口引导
在 Solaris SPARC 或 x86 平台上安装和配置 hxge 驱动程序
在 VMware ESX Server 平台上安装和配置驱动程序
hxge 设备驱动程序配置文件位于以下目录中
/kernel/drv/hxge.conf
以下是 /kernel/drv/hxge.conf 文件的内容。在此文件中列出并说明了所有参数。默认值在 hxge 驱动程序启动时装入。
# cat /kernel/drv/hxge.conf # # # driver.conf file for Sun 10Gb Ethernet Driver (hxge) # # #------- Jumbo frame support --------------------------------- # To enable jumbo support, # accept-jumbo = 1; # # To disable jumbo support, # accept-jumbo = 0; # # Default is 0. # # #------- Receive DMA Configuration ---------------------------- # # rxdma-intr-time # Interrupts after this number of NIU hardware ticks have # elapsed since the last packet was received. # A value of zero means no time blanking (Default = 8). # # rxdma-intr-pkts # Interrupt after this number of packets have arrived since # the last packet was serviced. A value of zero indicates # no packet blanking (Default = 0x20). # # Default Interrupt Blanking parameters. # # rxdma-intr-time = 0x8; # rxdma-intr-pkts = 0x20; # # #------- Classification and Load Distribution Configuration ------ # # class-opt-****-*** # These variables define how each IP class is configured. # Configuration options includes whether TCAM lookup # is enabled and whether to discard packets of this class # # supported classes: # class-opt-ipv4-tcp class-opt-ipv4-udp class-opt-ipv4-sctp # class-opt-ipv4-ah class-opt-ipv6-tcp class-opt-ipv6-udp # class-opt-ipv6-sctp class-opt-ipv6-ah # Configuration bits (The following bits will be decoded # by the driver as hex format). # # # 0x10000: TCAM lookup for this IP class # 0x20000: Discard packets of this IP class # # class-opt-ipv4-tcp = 0x10000; # class-opt-ipv4-udp = 0x10000; # class-opt-ipv4-sctp = 0x10000; # class-opt-ipv4-ah = 0x10000; # class-opt-ipv6-tcp = 0x10000; # class-opt-ipv6-udp = 0x10000; # class-opt-ipv6-sctp = 0x10000; # class-opt-ipv6-ah = 0x10000; # # #------- FMA Capabilities --------------------------------- # # Change FMA capabilities to non-default # # DDI_FM_NOT_CAPABLE 0x00000000 # DDI_FM_EREPORT_CAPABLE 0x00000001 # DDI_FM_ACCCHK_CAPABLE 0x00000002 # DDI_FM_DMACHK_CAPABLE 0x00000004 # DDI_FM_ERRCB_CAPABLE 0x00000008 # # fm-capable = 0xF; # # default is DDI_FM_EREPORT_CAPABLE | DDI_FM_ERRCB_CAPABLE = 0x5
在以下示例中,NEM 丢弃此刀片系统的 TCP 通信。换句话说,hxge 驱动程序不会接收任何 TCP 通信。
class-opt-ipv4-tcp = 0x20000;
在以下示例中,将禁用 FMA 功能。
fm-capable = 0x0;