C H A P T E R 3 |
Monitoring and Administration Commands for All Arrays |
This chapter describes the sscs commands and their options for monitoring and administrating all Sun arrays, including Sun Storage J4200, J4400, and J4500 arrays, Sun StorEdgeTM 6130 array, Sun StorageTekTM 6140 and 6540 arrays, Sun Storage 6580 and 6780 arrays, Sun StorageTek 2500 Series arrays, and FlexLineTM 240, 280, and 380 Systems. For the configuration and other commands that apply only to arrays with raid controllers, see Chapter 4.
Sets up email or SNMP trap notification.
add [ -e <email-address,...>] [ -c <array_type> ] [ -r pager | email ] [ -m down | critical | major | minor ] [ -f ] [ -s ] [ -d ] [ -g ] notification local_email
Add an SNMP trap notification:
add -i <IP-address,...> [ -o <port_id>] [-t 1 | 2 | 3 | 4 | 5 ] [-l warning | error | down ] [-m| <down | critical | major | minor>] [-c <community-string> ] [-g ] notification trap
add -n <event-id> -s info | none notification email-filter
Turn on the SNMP trap notifier:
add notification trap
Sets up email and SNMP trap notification. You can add one or more email addresses for notifications.
-e,--email <email-address,...>
Specifies that all notifications are sent to the given email addresses.
-i,--ip <IP-address,...>
Specifies the IP address of the host that will receive the SNMP trap data.
-l,--traplevel warning | error | down
Specifies the trap level associated with this notification.
-o,--port <port-id>
Specifies the port ID used to transfer notifications.
-c,--components <array_type>
Specifies the array model number. For example, j4200 or j4400.
-r,--format pager | email
Specifies the format of the message: email or pager. If no value is specified, the command defaults to email.
-m,--alarm-level down | critical | major | minor
Specifies the minimum priority level of alerts to be sent out. By default, all alerts will be sent out.
-f,--filter true | false
Enables or disables email filters. The default is false.
-s,--skip-aggregated true | false
Skips components of aggregated events if set to true.
-d,--advisor true | false
Adds Service Advisor information to the email if set to true. The default is false.
-g,--config-change true | false
Sends configuration event emails as well as alert e-mails. The default is false.
-n,--event-number <event_id>
Specifies the event code to filter.
-s,--severity info | none
Specifies the severity of events to report.
-t,--trapnumber 1 | 2 | 3 | 4 | 5
Specifies the trap number associated with this notification.
notification local_email | email-filter | trap
Specifies that all notifications of the specified type are sent to the given addresses.
local-email - Specifies that you want to receive the notification at your local email address.
email-filter - Specifies that you want to filter the notification.
trap - Specifies that you want to receive notification using the SNMP trap notification.
sscs add -t 2 -i 10.10.10.1 notification trap
Discovers an array or all arrays on the same subnet as the management host and registers them.
add -d registeredarray add -i [ -q ] registeredarray
Discovers an array by specifying its IP address or all arrays on the same subnet as the management host and registers them. Also queries registered arrays for the remote proxy password.
-i,--ipaddress
Specifies the IP address of the device.
-d,--discover
Automatically discovers all arrays on the same subnet as the management host and registers them. If discover is specified, all other options are ignored and arrays are automatically discovered.
-q,--query-for-password
Queries for the current password for remote proxy for the registered array.
sscs add -i 10.10.10.1 registeredarray
Adds a user name to the user access list and defines the user privileges.
add -u <user-name> userrole storage | guest
Adds a user name to the user access list and defines the user role as having storage or guest privileges.
-u,--username <user-name>
Specifies a user name. The <user-name> must already be defined on the computer in the operating system.
userrole storage | guest
Specifies the new user’s role.
storage - Provides full storage configuration and monitoring access.
guest - Allows user to view but not change storage configurations.
Provides detailed information on a specified alarm or summary information on all alarms.
list [ -s <1..3> ] [ -f <device-type> ] [ -a <service-advisor-ID> ] [ -S ] alarm [ <alarm_ID> ]
Provides detailed information on a specified alarms. When alarm IDs are not specified, it provides summary information on all alarms.
-a,--advisor service-advisor-ID
-s,--severity <1..3>
Specifies a severity level at which to filter alarms so that only the alarms of that severity level are listed.
-f,--faultdevtype <device-type>
Specifies the type of device to list.
-S, --Summary
Specifies that the system return a summary of alarm information.
alarm [ <alarm_ID> ]
Specifies the alarm or alarms to display. If no alarm is specified, summary information on all alarms is displayed.
sscs list -f j4200 alarm sscs list -s 2 alarm sscs list -s 1 -a alarm
(when no advisor option is specified)
Alarm ID: ID Severity: severity Type: type Topic: topic Event Code: event-code Date: date Device: device-id Descrip.: Description
(when the advisor option is specified) Alarm ID: ID Severity: severity Type: type Topic: topic SERVICE ADVISOR EventCode: event-code EventType: event-type Severity: severity-level Sample Description: event-Description Information: event-information Probable Cause: probable-cause Recommended Action: recommended-action Date: date Device: device-ID Descrip.: Description
Lists detailed information about specified arrays or all array names.
list array [ <array-name,...> ]
Lists detailed information about one or more arrays. If you do not specify an array name, then all array names are listed.
Summary of arrays when no <array-name> value is specified:
Detail of array when the <array-name> value is specified (shows array with raid controller):
Firmware Version: firmware-version
Hot-Spare Pool Disks: number-of-hot-spare-drives (FC, SATA, and SAS)
Default Cache Block Size: 4K | 16K
Default Cache Start %: <0..100>
Default Cache Stop %: <0..100>
Disk Scrubbing: Disabled | Enabled
Failover Alert Delay: 1..300 minutes
Health: OK | Lost Contact |...
Lists the current date and time for the array in hours, minutes, and seconds. (Not supported by j450 and B6000 JBODs.)
list -a <array-name> date
Lists the current date and time for the array in hours, minutes, and seconds. The time zone of the management system is assumed to be the time zone of the array.
-a,--array <array-name>
Specifies the array for which you want to see the date.
sscs list -a array00 date
Date: weekday month day HH:MM:SS YYYY
Provides detailed information on a specified device or summary information on all devices.
list [ -n <device-name> ] [ -i <IP-address>] device [ device-ID [,device-ID...]] list devices
List the details of a device or the devices being monitored.
-n,--name <device-name>
Specifies the device name for which you want to see the details. If no device is specified, summary information for all devices is displayed.
-i,--ip <IP-address>
Specifies the IP address of the connected host when using remote proxy.
Specifies one or more device IDs.
sscs list -n 2540_array1 device Device Name : 2540_array1 Type : 2540 IP Address : 10.nn.nn.n Monitored On : sp-72 Key : SUN.14617-00.0617053335 Active : Y WWN : 200400a0b82458a0 Alternate IP : 10.nn.nn.n Alt IP Number : 10.nn.nn.n Management Level : D Said : 600A0B80002458810000000045A7B14E Time Added : 2008-10-03 11:44:11 Port WWNs : 200400a0b82458a1,200400a0b82458a2,200500a0b82458a1,200500a0b82458a2 sscs list -i 10.1.1.1 device sscs list device
DeviceName: device-ID Type: type IP Address: IP-address Monitored On: interface Key: device-key Active: Is the device active? Y | N WWN: World Wide Name MgmtLevel: management-level Said: Storage-Automated-Diagnostic-Environment-Identifier Time Added: time added
Provides summary information on all devices.
list devices
List a summary of the devices being monitored.
list devices Monitored On Device Type IP Address WWN Active ASR --------- ------------ ---- ------------- ---------------- ------ --- sp-72 2540_array1 2540 10.nn.nn.n 200400a0bnnnnnnn Y N sp-72 6140_array2 6140 10.nn.nn.n 200400a0bnnnnnnn Y N sp-72 6140_array3 6140 10.nn.nn.n 200400a0bnnnnnnn Y N
Monitored On: interface Device Array/system being monitored Type Array/system model IP Address IP-address WWN World Wide Name Active Is the device active? Y | N ASR Is Auto Service Request on? Y | N
List the disk information on an array.
list -a <array-name> disk [ <disk-name,...> ]
-a,--array <array-name>
Specifies the name of the array where the disk resides.
disk <disk-name,...>
This option provides detailed information on the specified disks. When disks are not specified, this option provides detailed information on all the disks in the tray.
sscs list -a array00 -t 1 disk
Tray: tray-ID Disk: disk-name Capacity: disk-capacity Type: SAS | SATA Speed (RPM): speed-in-revolutions-per-minute Status: Optimal | In-use | Available | Failed State: Enabled | Disabled Role: Data Firmware: firmware-version-number Serial number: serial-number WWN: WWN-number
Lists the Fault Management Service (FMS) event log information.
list [ -s <1..3> ] [ -d <device_id> ] [ -t <type> ] [ -a ] [ -f <keyword> ] [ -l <limit> ] event [ <event_Id> ]
Lists the FMS event log information. You can filter by device type and severity level.
-s,--severity <1..3>
Specifies a severity level at which to filter events so that only the events of that severity level are listed.
-d,--device <device_id>
List only events for the given device.
-t,--type <type>
List only events of the given event type.
-a,--aggregated
Specifies that all events are listed and aggregated so that related events are grouped together.
-f, --filter <keyword>
Filter output on the event Description by using the given keyword parameter.
-l,--last <limit>
Limit the number of events printed by the given number.
event <event_id>
sscs list -s 3 event
Severity : Minor Date : Fri Mar 10 10:39:57 MST 2006 Device : diag-lsi1 (J4200) Component : Sim.0 Type : Problem Event Code : Aggregated : No Description : New problem REC_NON_FRU_BATTERY_NEAR_EXPIRATION t0ctrl2:39 discovered on diag-lsi1 "t0ctrl2".
Lists the firmware versions of the field-replaceable units (FRU) in this device.
list [ -a <array-name> ] [ -t <type> ] [-x <component_type1 [,component_type1...]>] firmware
Lists the firmware versions of the field-replaceable units in this device. You can define the FRUs to include or exclude.
-a,--array <array-name>
Shows the firmware revision level of the field-replaceable units for the specified array only.
-t <component_type>
Shows the firmware revision level for the specified component type.
-x, --exclude <component_type>
Excludes the specified component type from the list of firmware revision levels.
List the component firmware revisions for all arrays.
sscs list firmware
List the component firmware revisions for a specified array.
sscs list -a jbod1 firmware
Lists the field-replaceable units (FRUs) in this device.
list -d <device-name> [ -t <type-name> ] [ -s ] fru [ string,... ]
Lists the field-replaceable units in this array. You can filter by component type.
-d, --device <device-name>
-t,--type <type-name>
Specifies the type of field-replaceable units installed in this device to list. Use the -s option to see which FRU types would be valid for the chosen device. For example, for the JBOD arrays valid types are:
disk | fans | power supplies | sim | all
-s,--summary
Lists a summary of this field-replaceable unit.
fru [string,...]
Lists the field-replaceable unit or units in this device.
sscs list -d jbod1 fru
Output includes the component name, FRU type, alarm state, status, revision, and unique ID.
sscs list -d nenc-447 -t all -s fru
Type Description Alarm Installed Slot Count -------- ----------- -------- --------- ---------- battery battery Major 2 2 ctrl ctrl Critical 2 2 disk disk - 10 32 icc icc - 1 1 iom iom - 4 4 midplane midplane - 3 3 pcu pcu Critical 6 6 sfp sfp Critical 8 24
Lists job IDs and status associated with the specified array and optionally specified job ID.
list -a array-name jobs [job-id [,job-id...]]
Lists job IDs and status associated with the specified array and optionally specified job ID.
-a,--array <array-name>
Specifies the name of the array.
job-id
sscs list -a jbod1 jobs
Job ID: Install:task27 Status: Done
Job ID: Install:task36 Status: Done
Job ID: Install:task32 Status: Done
Job ID: Install:task35 Status: Done
Job ID: Install:task25 Status: Done
Job ID: Install:task24 Status: Done
Job ID: Install:task45 Status: Done
Job ID: Install:task30 Status: Done
Job ID: Install:task33 Status: Done
Job ID: Install:task34 Status: Done
sscs list -a jbod1 jobs Install:task27
Lists the user-initiated actions performed for all registered arrays.
list [ -s { [ mmdd ] HHMM | mmddHHMM [ cc ] yy } [ .SS ] ] [ -f { [ mmdd ] HHMM | mmddHHMM [ cc ] yy } [.SS ] ] [ -t <number-of-messages> ] log
Lists the user-initiated actions performed for all registered arrays. You can filter the listings by date and time or most recent entries. If you do not specify any options, all log messages are displayed.
-s,--start { [ mmdd ] HHMM | mmddHHMM [ cc ] yy } [ .SS ]
Lists all log messages starting at the date specified by the date options. Use with the -f,--finish subcommand to specify a date range.
-f,--finish { [ mmdd ] HHMM | mmddHHMM [ cc ] yy } [ .SS ]
Lists all log messages ending at the date specified by the date options. Use with the -s,--start subcommand to specify a date range.
mmdd
Specifies the month and day. For example, 0331 for March 31.
HHMM
Specifies the hour and minute. The hour is based on a 24-hour clock. For example, 1:30 p.m. is 1330.
cc
Specifies the century part of the year.
yy
.SS
Specifies the seconds of the hour.
-t,--tail <number>
Lists the most recent log messages as specified by number.
sscs list -t 100 log
Timestamp:message
list mgmt-sw
Lists the management software application that you are logged into.
sscs list mgmt-sw
Application Name: “Sun StorageTek(TM) Common Array Manager” User: storage Current Logins: 2 Server: 10.8.88.173 Server OS: SunOS Server OS Version: 5.10 Product Version: 4.2.0.0 Build Date: 2005/12/03 Install Info: 4.2.0.0 Build 61 Critical Alarms: 13 Down Alarms: 0 Major Alarms: 24 Minor Alarms: 0
list notification
Lists the remote notification provider and its status.
sscs list notification
Entry Email/Events Type Device Priority Events enter-no email-address notification-type device-type priority events Provider Active Heartbeat (hrs) IP provider active-flag frequency IP Address Trap # IP Name/Address Port Min Alert Level trap-no IP Address Port Trap level
Lists registered array information.
list -a [ <array-name,...> ] registeredarray
Lists registered array information or the names of all arrays.
-a,--array <array-name,....>
Specifies the registered array or arrays to list. If no arrays are specified, a list of all array names is provided (optional).
sscs list -a array01 registeredarray
(summary if no <array-name> values are specified)
Array Name: array-name ... Array Name: array-name
(detail if <array-name> values are specified)
Array Name: array-name IP Address: IP-address ... IP Address: IP-address
list site
Lists pertinent information on the site.
sscs list site *Company Name : Sun Microsystems *Site Name : Interop Lab Address : Address 2 : Mail Stop : *City : Broomfield State : *Country : USA *Contact First Name : Fred *Contact Last Name : Jones Telephone Number : Extension : *Contact Email : Fred.Jones@sun.com
Lists detailed information about one or more arrays.
list storage-system [ <array_name,...> ]
Lists detailed information about one or more arrays. If you do not specify an array name, then all array names are listed.
sscs list storage-system
(Summary of arrays when no <array-name> value is specified)
Array: array-name ... Array: array-name
Detail of array when the <array-name> value is specified)
./sscs list storage-system Flx380-1 Name: Flx380-1 ID: Flx380-1 Type: 6140 Version: 06.19.25.26 Vendor: SUN Microsystems Model: Sun StorEdge 6140 System Capacity: 367039329280 Available Capacity: 110674668544
Lists the user name and role defining the user’s array privileges.
list userrole [ storage | guest ]
Lists the user name and role defining the array privileges.
userrole storage | guest
List the users with the specified role. The storage role allows write access so that the user can configure the array. The guest role can only monitor the array.
sscs list userrole storage
User Name: user-name User Role: user-role ... User Name: user-name User Role: user-role
Log in to the sscs command-line interface (CLI).
login -h <host-name> [ -s CAM | Legacy ] [ -t ] [ -f ] -u <user-name>
Log in to the sscs command-line interface (CLI) on the management system specified by the -h <host-name>. This command starts a CLI session on the management host.
There are two forms of the CLI:
The only difference is that the local CLI requires a user has to run the command as administrator from a shell on the management host and because of this limitation the login and logout commands aren’t supported.
Both CLIs can manage any array that has been registered and added to the Common Array Manager inventory in the same way that the browser interface can manage any array in the inventory. The array type and array management path (in-band, out-of-band, proxy agents) has no limitations with local or remote CLI usage. Both CLIs manage the same arrays with the same command set.
The following explains how to log in to and out of a the management host using the CLI. The options for accessing the CLI are presented in the next section.
There are different CLI directories for the remote and local CLIs.
1. Telnet or ssh to the CAM workstation.
ssh root@cam_workstation1
2. Change to the CLI directory (varies by operating system).
a. Access the remote CLI directory:
3. Log into the remote CLI by typing the following command:
% sscs login -h <host-name> -u <user-name>
Note - The Local CLI on a data host does not require the login command. You will need the terminal window login to the host. |
b. Access the local CLI directory:
NOTE: sscs has an inactivity timer. The session terminates if you do not enter any sscs commands for 30 minutes. You must log in again before you can enter a command after the timeout.
-h,--hostname <host-name>
Required. Specifies the management host name.
-s,--system-type CAM | Legacy
Optional. This option specifies whether you are logging into any of the current arrays supported by the Common Array Manager or the now legacy 6920 array. In some cases, using the -s CAM option may log you in faster as it skips a step of listening for a response from the legacy array.
You no longer have to specify the array-type to login.
-t,--http
Enables you to use the HTTP protocol to connect to the CAM server, instead of HTTPS. An HTTP connector is configured in Tomcat, the servlet container in Java, for the Java Web Console at port 6789. If SSL is not functioning between the client and the server, this might be required.
-f,--force
Exists for backward compatibility with legacy management applications that only allow one login per user. This option forces a login to the management host. If another user with the same user name is already logged on, the duplicate user is then logged off.
-u,--username <user-name>
Specifies the user name that to log in.
./sscs login -h localhost -u root
logout
Logs out of the remote sscs command-line interface session.
Modify the fault management agent parameters.
modify [ -a ] [ -d ] [ -r ] [ -i <integer> ] agent [ <agent_id> ]
Modify the fault management agent parameters. Fault Management Service (FMS) periodically scans devices for new messages and updated health status. This command allows changing the scan interval as well as enabling or disabling the scan. If no options are given the current agent settings are printed out.
Internal agent properties can be set by using name=value for the strings on the agent.
The most common property to be set is debug=0,1,2,3 to turn on agent debugging.
All other properties are for service only.
-a,--activate
Specifies that the system activate the monitoring agent.
-d,--deactivate
Specifies that the system deactivate or turn off the monitoring agent.
-r,--run
Specifies that the system schedule the agent to run either immediately or as soon as the currently scheduled run has finished.
-i,--interval <integer>
Specifies the interval, in minutes, before the agent scan runs.
agent [ <agent_id> ]
Specifies the agent that you want to modify. The name of the agent monitoring the device can be retrieved using the list device command
sscs modify -i 5 agent
modify [ -N <new-array-name> ] array <array-ID>
Modifies the name assigned to the array.
Note - Refer to the modify array command in Chapter 4 for the extensive configuration options that apply to arrays with raid controller. |
-N,--new-array-name <array-name>
Specifies the new name of the array.
array <array-ID>
Specifies the name of the array to be modified.
sscs modify -n array2 array jbod1
Modifies the firmware versions of the specified field-replaceable units (FRUs) of the specified array.
modify -a <array-name> [ -f ] -o [ -t sim | disk ] [ -x sim | disk ] [ -p <path>] [ -c <field-name>] [ -w ] firmware
Modifies the firmware versions of the specified field-replaceable units of the specified array.
-a,--array <array-name>
Modifies the firmware revision level of the specified field-replaceable units for the specified array only.
-c,--component <field-name>
Modifies the firmware for the selected components. To get the valid values, execute the sscs list -a <array-name> firmware command. Use either the Name or Model field values.
-f,--force
Modifies the firmware revision level of the all field-replaceable units even if the firmware revision level is already at the baseline level.
-o,--offline
Performs an offline upgrade of the specified component(s).
-p,--path <path>
Specifies the path of the firmware image file. Loads firmware from a file directly onto the array. Caution should be exercised when using this command because unsupported firmware can be loaded onto a field-replaceable unit. If -p option is provided, the -c option is required.
-t,--type <fru-type>
Modifies the firmware revision level of the field-replaceable units of the specified type only.
-w,--no-warn
Modifies the firmware without displaying the standard warning.
-x,--exclude sim | disk
Excludes the specified component from being upgraded.
modify - a MyArray -f firmware
modify -X <storage-system-name> mgmt-sw
Stores the specified storage system name for the session. This command is useful for repeated operations with an array. After this command is executed, the -a option for subsequent sscs commands is not necessary.
-X,--storage-system <storage-system-name>
Specifies the name of the storage system.
modify -X MyArray mgmt-sw
Change the locally stored password for a registered array.
modify -a <array-name> -q registeredarray
Modifies the locally stored password for a registered array or queries for the current password.
-a,--array <array-name>
Specifies the name of the array to be modified.
-q,--query-for-password
Queries for the current password for the registered array.
sscs modify -a array00 -q registeredarray New Password: myregisteredarray Re-enter New Password: myregisteredarray
Modifies the site properties for this instance of CAM.
modify [ -r < site_info >,... ] site [ < site_info = value >,... ]
Modifies the site properties for this instance of CAM. The site properties contain information about the site and provides information needed for the notification providers.
-r,--remove < site_info >
Removes the specified site information.
site < site_info = value >
Modifies existing site settings or adds new site information. Possible values for site_info are: customer, contract, name, address, address2, mailStop, city, state, country, contact, phone, email. Possible values for value consist of an alphanumeric string. If the string includes spaces, enclose the values in quotes.
sscs modify site name=”Development Lab” sscs modify -r name site
Modifies the array information.
modify [ -N <storage-system-name> ] [ -d <Description-text> ] [ -u <user-name> ] [ -q ] [ -U <user-name> ] [ -Q ] storage-system <storage-system-name>
Modifies array information such as array name, description, and user name.
-d,--Description
Provides a textual description of the array.
-N,--new-name
-q,--query-for-password
-u,--user-name
Changes a username on the array.
storage-system <storage-system-name>
Specifies the array where the changes will take effect.
sscs modify -q storage-system MyArray Enter the array password: Confirm password:
Change the user role or the IP address from which the user can log in.
sscs modify -u <user-name> -p <password> -i ANY | <IP-address,...> userrole [ storage | guest ]
Modifies a user role or the IP address from which the user can log in. The storage role can perform configuration changes while the guest role can just monitor an array.
-u,--username <user-name>
Specifies the user name that has an assigned role (storage or guest).
-p,--password-required true | false
Specifies whether to require user login with a password.
-i,--ip-address ANY | <IP-address,...>
Specifies the IP addresses from which the user can log in. You can let the user log in from anywhere or restrict access to specified IP addresses.
userrole storage | guest
Specifies the role assigned to the user.
sscs modify -u bsmith -p true -i ANY userrole guest
register -i <ip-address> [ -p <port-id> ] [ -u <user-name> ] [ -q ] [ -U <user-name> ] [ -Q ] storage-system register -d storage-system
Registers a storage system with the host.
-d,--discover
Specifies that the host will discover a registered array.
-i,--ipaddress <ip-address>
Specifies the IP address of the storage system that you want to register.
-p,--port <port-id>
Specifies the port ID of the storage system that you want to register.
-u,--user storage | root | guest
Specifies the user name that has an assigned role.
-q,--query-for-password
Specifies whether to query for a password for this registered storage system.
-U,--device-specific-user <user-name>
Specifies a specific name for this device.
-Q,--query-for-device-specific-password
Specifies whether to query for a specific password for this registered device.
Registers CAM software and all monitored arrays with Auto Service Request.
register [ -u <sun_online_account_username> ] [ -H <proxy-host-name> ] [ -P <proxy-port_number> ] [ -U <proxy_username> ] [ -e all | telemetry ] [ -d <all | telemetry> ] sun-connect
Registers CAM software and all monitored arrays with Auto Service Request. Auto Service Request monitors the array system health and performance and automatically notifies the Sun Technical Support Center when critical events occur. Critical alarms generate an Auto Service Request case. The notifications enable Sun Service to respond faster and more accurately to critical on-site issues. All newly discovered arrays will also be registered with the saved registration options.
-d,--disable all | telemetry
Disables all telemetry mechanisms.
-e,--enable all | telemetry
Enables all telemetry mechanisms.
-H,--proxyHost <proxy-host-name>
Specifies the proxy host name.
-P,--proxyPort <proxy-port_number>
Specifies the proxy port number.
-U, --proxyUser <username>
A proxy host authenticated user name.
-u,--user <sun_online_account_username>
Specifies a valid Sun online account user name. To get one go to: https://portal.sun.com/portal/dt/
sun-connect
Specifies that you are registering the CAM software and all monitored arrays with Auto Service Request.
sscs register -H Proxy1 -P 8080 -u MySunAcctId -e telemetry sun-connect
remove [ -f <device-type> ] [ -s 0 | 1 | 2 | 3 ] [ -A ] alarm [ <alarm-ID,...> ]
-f,--faultdevtype <device-type>
Removes alarms by the device type using a device key filter.
-s,--severity string
Specifies the severity level for which you want to remove alarms.
alarm <alarm-ID,...>
Specifies the alarm ID or alarm IDs you want to remove.
sscs remove -f 6140 alarm sscs remove -s 2 alarm sscs remove -A alarm
Removes a local or remote notification.
remove [-e <string[,string...]>] notification local_email | email-filter | trap remove [-i <IP-address>] [-o <string>] [-t 1 | 2 | 3 | 4 | 5 ] notification local_email | email-filter | trap remove -d <string[,string...]> notification local_email | email-filter | trap remove [-c <category-id>] [-e <event-id>] [-a ] notification <emailAddress[,emailAddress...]>
Removes a local or remote notification.
-a, --all
Specifies that all notifications should be removed.
-c, --category <category-id>
Removes the specified category ID notification.
-d, --id <string,string...>
Removes the specified device ID notification.
-e,--email <string[,string...]>
Stops notifications to the specified recipient.
-e, --event <event-id>
Stops email notifications with the specified event ID.
-i, --ip <IP-address>
Stops sending SNMP trap data to the IP address of the specified host.
-t,--trapnumber 1 | 2 | 3 | 4 | 5
Stop notifications for the specified trap number.
-o,--port <port-id>
Specifies the port ID used to transfer notifications.
local-email
Removes the notification from your local email address.
email-filter
Removes the email filter from the notification.
trap
Removes the SNMP trap notification.
sscs remove -e john.doe@address.com notification local_email sscs remove notification nscc_email sscs remove -t 2 notification trap
Removes one or more arrays from the list of registered arrays.
remove -a <array-name,...> registeredarray
Removes one or more arrays from the list of registered arrays.
-a,--array <array-name,...>
Specifies the registered arrays to remove.
sscs remove -a array00 registeredarray
Removes a user role assigned to a user name.
remove -u <user-name,...> userrole storage | guest
Removes the privileges (storage or guest role) assigned to a user name.
-u,--username <user-name,...>
userrole storage | guest
Specifies the user’s role to remove.
sscs remove -u jf39992 userrole guest
Perform service-related commands.
service -a <array-name> [ contact | locate [ -o ] | print [ -t <arrayprofile | log | drive_id> ] enable | disable | set name=<new-name> | syncTime ]
Use this command to perform inband communication tests, locate an array by turning its LED on or off, print the contents of the array profile or log file, change the name of the array, and synchronize the time of a JBOD array with the attached data host.
-a,--array <array-name>
Specifies the array to perform a service.
-t,--target arrayprofile | log
Specifies the target file to print.
-o,--off
contact
Tests connectivity to the array (inband communication test).
disable
Disables the specified target drive.
enable
Enables the specified target drive.
locate
Locates the array by turning LED on.
name=<new-name>
Changes the name of the array to the specified name.
Prints all physical information available for the specified array.
syncTime
Synchronize the time of the JBOD array with the attached host.
Turn off all LED locate indicators on the specified arrays.
sscs service -d "JBOD(2029QTF0802QCK00E)" -t off locate
Set the JBOD name to J4200_box1
sscs service -d "JBOD(2029QTF0802QCK00E)" name=J4200_box1 set
Disable drive00 on the array named J4400_box3.
sscs service -a j4400_box3 -t drive00 disable
unregister storage-system <storage-system-name,...>
Unregisters an array from the list of registered storage systems.
storage-system <storage-system-name,...>
Specifies the storage system or storage systems that you want to unregister from the list of registered storage-systems.
sscs unregister storage-system array19
Stop notifications of system health and performance to Sun using the Auto Service Request (ASR) feature.
unregister sun-connection
Stops sending system health and performance information on monitored arrays back to Sun. Newly discovered arrays will not be activated with ASR.
sscs unregister sun-connect
Shows the versions of software that you are running on the management host and the SSCS client.
-V, --version
Shows the versions of software that you are running on this array and the client.
sscs -V Sun StorageTek(TM) Common Array Manager v6.1.1.0 sscs client v1.1.4
Copyright © 2008 Sun Microsystems, Inc. All Rights Reserved.