Sun Java Communications Suite 5 Installation Guide

Resolving Installation Problems

This section addresses the following problems you might encounter during installation.

Installation Fails Due to Leftover Files During Uninstallation

Uninstallation can leave behind product components or packages. In such a case, you must manually remove the product components or packages before you reinstall Communications Suite. You might discover this problem in the following ways:

ProcedureTo Clean up a Partial Installation

  1. Use the following command to determine whether any packages were partially installed.

    Solaris OS: pkginfo -p


    rpm -qa |grep —I ^sun | xargs rpm -V

    The command output lists any partially installed packages. Using the package names returned, refer to Chapter 5, List of Installable Packages, in Sun Java Enterprise System 5 Installation Reference for UNIX to discover what product component the packages belong to.

  2. Remove components or packages.

    • On Solaris 9 or 10, use the prodreg tool.

      The prodreg tool manages the package-based components on your host. You can view product components and their packages, with full information, including interdependencies. You can use the prodreg tool to safely uninstall product components and remove packages. Once you have removed a product component with the prodreg tool, you can reinstall.

    • On Linux, use the rpm -e command.

      To edit the product registry file, open the file /var/opt/sun/install/productregistry. This XML file describes each product component. Each product component description starts with a <compid\> tag and ends with a </compid\> tag. Delete the entire entry for the product component.

  3. Verify that the following directories do not contain Communications Suite product components or packages:




  4. Run the installer again.

Installation Fails Due to Removed Shared Components in Product Registry After Uninstallation

As of the Communications Suite 5 release, shared components are listed in the product registry file after installation.

The uninstaller removes product components from the system but does not remove shared components. After an uninstallation, the product registry still contains entries for the shared components. If you manually remove any shared components after an uninstallation, these components are not removed from the product registry. Thus, the next Communications Suite 5 installation fails because the installer assumes that the manually deleted shared components are present (because they still have entries in the product registry file).

Tip –

Avoid manually removing Communications Suite shared components from your system.

Suggested Fix. Either remove the corresponding entries from the product registry file or remove the product registry file itself. Removing entries from the product registry file can cause the file to become corrupted, so you might prefer to remove the whole product registry. Before doing this, verify that products other than Communications Suite components are not using the product registry file.

On Linux there is no equivalent of the graphical product registry that exists on Solaris OS. If you manually removed files on Linux, you must manually edit the product registry file to remove those entries.

Unexpected External Error Occurs

A power failure or system failure might have occurred, or you might have entered CTRL/C to stop the installer process.

Suggested Fix. If the failure occurred during the installation or configuration process, you are probably left with a partial installation. Run the uninstaller. If the uninstaller fails, follow the instructions under Uninstallation Fails, Leaving Behind Files

Graphical Installer Seems Unresponsive

The installer sometimes creates an image on the screen before the image is ready for input. You cannot repeatedly click Next in the installation wizard without waiting.

Suggested Fix. The button that represents the default choice includes a blue rectangle. This rectangle sometimes appears after the button itself appears. Wait until you see the blue rectangle before clicking a button.

Silent Installation Fails: “State File is Incompatible or Corrupted”

If you are using a state file that was created on the same platform on which you are using it, the problem might be due to an unknown file corruption error. There are two approaches to troubleshooting this issue.

Generate a New State File

Create a New Platform-Appropriate ID

If the platform on which you created the state file is not the same as the platform on which you are running the silent installation, create a new, platform-appropriate ID for the file. For instructions on how to do this, refer to Creating a Platform-Appropriate State File ID.

Silent Installation Fails

If you edited the state file, you might have introduced errors. Check the following and regenerate the state file as described in Creating a State File.

Suggested Fix. Resolve the problem and regenerate the state file.

Man Pages Do Not Display

The most likely reason for this is that your MANPATH environment variable is not set correctly for the components you installed.

Suggested Fix. Update /etc/MANPATH to point to the new man page directory. Refer to Verifying the MANPATH.