Sun Cluster 3.0-3.1 With SCSI JBOD Storage Device Manual for Solaris OS

Preface

The Sun Cluster 3.0-3.1 With SCSI JBOD Storage Device Manual for Solaris OS provides procedures specific to SCSI JBOD storage devices in a Sun^TM Cluster environment. Use this manual with any version of Sun Cluster 3.0 and 3.1 software on SPARC® based systems and with any supported versions of Sun Cluster 3.1 software on x86 based systems.

Note –

In this document, the term “x86” refers to the Intel 32-bit family of microprocessor chips and compatible microprocessor chips made by AMD.

Sun Cluster software runs on two platforms, SPARC® and x86. The information in this document pertains to both platforms unless otherwise specified in a special chapter, section, note, bulleted item, figure, table, or example.

SPARC only –

In this document, references to Oracle Real Application Clusters also apply to Oracle Parallel Server, unless otherwise stated.

Who Should Use This Book

This book is for Sun representatives who are performing the initial installation of a Sun Cluster configuration and for system administrators who are responsible for maintaining the system.

This document is intended for experienced system administrators with extensive knowledge of Sun software and hardware. Do not use this document as a planning or presales guide. You should have already determined your system requirements and purchased the appropriate equipment and software before reading this document.

How This Book Is Organized

This book contains the following chapters.

Chapter 1 discusses how to install SCSI JBOD storage devices.
Chapter 2 describes how to maintain SCSI JBOD storage devices in a running cluster.
Chapter 3 contains cabling diagrams for SCSI JBOD storage devices.

Revision History

The following table lists the information that has been revised or added since the initial release of this documentation. The table also lists the revision date for these changes.

Table P–1 Sun Cluster 3.0-3.1 With SCSI JBOD Storage Device Manual for Solaris OS


Revision Date	New Information
January 2006	Added information on single dual-port HBA configurations.
October 2005	Added Sun StorEdge 3320 as a supported array.
September 2005	Added information to support Sun StorEdge^TM 3310 and 3120 JBOD devices on x86 based systems.

Related Documentation

The following books provide conceptual information or procedures to administer hardware and applications. If you plan to use this documentation in a hardcopy format, ensure that you have these books available for your reference.

The following Sun Cluster books support the Sun Cluster 3.1, 2004, and 2005 releases. If you are maintaining a different version of Sun Cluster software, refer to the appropriate documentation. All Sun Cluster documentation is available at http://docs.sun.com.

Documentation that is not available at http://docs.sun.com is listed with the appropriate URL.

The related books are organized by the following products and subjects:

Table P–2 Sun StorEdge 3310 and 3320 SCSI Storage Array


Title	Part Number
OpenBoot 4.x Command Reference Manual Available at `http://docs.sun.com/db/doc/817–1177–10`	817–1177
Sun StorEdge 3000 Family Installation, Operation, and Service Manual, 3320 SCSI Array Available at `http://docs.sun.com/db/doc/819–1274–11`	819–1274
Sun StorEdge 3000 Family Installation, Operation, and Service Manual, 3310 SCSI Array	816–7290
Sun StorEdge 3000 Family FRU Installation Guide	816–7326
Sun StorEdge 3000 Family CLI 2.0 User’s Guide	817–4951
Sun StorEdge PCI Dual Ultra3 SCSI Host Adapter Release Notes	816-2157
Sun StorEdge 3310 SCSI Array Release Notes	816-7292
Sun StorEdge 3320 SCSI Array Release Notes Available at `http://docs.sun.com/db/doc/816-7660–10`	816-7660

Table P–3 Sun StorEdge 3120 Storage Array


Title	Part Number
Sun StorEdge 3000 Family FRU Installation Guide	816–7326
Sun StorEdge 3000 Family Installation, Operation, and Service Manual, Sun StorEdge 3120 SCSI Array	816–7956
Sun StorEdge 3120 SCSI Array Release Notes	816–7955
Sun StorEdge 3120 SCSI Array Quick Installation Guide Shipped with your storage array	816–7962
Sun StorEdge 3000 Family CLI 2.0 User’s Guide	817–4951

Table P–4 SPARC: Sun StorEdge D1000 Storage Array or Sun StorEdge Netra^TM st D1000 Storage Array


Title	Part Number
Netra st A1000/D1000 Installation and Maintenance Manual	805-7147
Netra st A1000/D1000 Product Notes	805-7148
OpenBoot 4.x Command Reference Manual Available at `http://docs.sun.com/db/doc/806-2906–10`	806-2906
Sun StorEdge A1000 and D1000 Installation, Operations, and Service Manual	805-2624

Table P–5 SPARC: Sun StorEdge Netra D130/S1 Storage Array


Title	Part Number
Netra st D130 Installation and Maintenance Manual	806-1489

Table P–6 SPARC: Sun StorEdge D2 Storage Array


Title	Part Number
Sun StorEdge D2 Array Installation, Operation, and Service Manual	816-2578

Table P–7 SPARC: Sun StorEdge Multipack Storage Array


Title	Part Number
OpenBoot 4.x Command Reference Manual Available at `http://docs.sun.com/db/doc/806-2906–10`	806-2906
SPARCstorage MultiPack 2 Service Manual	805–1667

Table P–8 Sun Cluster Documentation


Application	Title
Concepts	Sun Cluster Concepts Guide for Solaris OS
Overview	Sun Cluster Overview for Solaris OS
Hardware administration	Sun Cluster 3.0-3.1 Hardware Administration Manual for Solaris OS Individual hardware administration guides
Software installation	Sun Cluster Software Installation Guide for Solaris OS
Data service administration	Sun Cluster Data Services Planning and Administration Guide for Solaris OS Individual data service guides
Data service development	Sun Cluster Data Services Developer’s Guide for Solaris OS
System administration	Sun Cluster System Administration Guide for Solaris OS
Error messages	Sun Cluster Error Messages Guide for Solaris OS
Command and function reference	Sun Cluster Reference Manual for Solaris OS
Release Notes	Sun Cluster 3.1 8/05 Release Notes for Solaris OS Sun Cluster 3.0-3.1 Release Notes Supplement

Using UNIX Commands

This document contains information about commands that are used to install, configure, or upgrade a Sun Cluster configuration. This document might not contain complete information about basic UNIX® commands and procedures such as shutting down the system, booting the system, and configuring devices.

See one or more of the following sources for this information:

Online documentation for the Solaris^TM Operating System (Solaris OS)
Other software documentation that you received with your system
Solaris Operating System man pages

Getting Help

If you have problems installing or using Sun Cluster, contact your service provider and provide the following information.

Your name and email address (if available)
Your company name, address, and phone number
The model number and serial number of your systems
The release number of the operating environment (for example, Solaris 9)
The release number of Sun Cluster (for example, Sun Cluster 3.1 8/05)

Use the following commands to gather information about your system for your service provider.

Command	Function
`prtconf -v`	Displays the size of the system memory and reports information about peripheral devices
`psrinfo -v`	Displays information about processors
`showrev -p`	Reports which patches are installed
`prtdiag -v`	Displays system diagnostic information
`/usr/cluster/bin/scinstall -pv`	Displays Sun Cluster release and package version information

Also have available the contents of the /var/adm/messages file.

Documentation, Support, and Training

The Sun web site provides information about the following additional resources:

Typographic Conventions

The following table describes the typographic conventions that are used in this book.

Table P–9 Typographic Conventions


Typeface	Meaning	Example
`AaBbCc123`	The names of commands, files, and directories, and onscreen computer output	Edit your `.login` file. Use `ls -a` to list all files. `machine_name% you have mail.`
`AaBbCc123`	What you type, contrasted with onscreen computer output	`machine_name%` `su` `Password:`
`aabbcc123`	Placeholder: replace with a real name or value	The command to remove a file is `rm` `filename`.
AaBbCc123	Book titles, new terms, and terms to be emphasized	Read Chapter 6 in the User's Guide. A cache is a copy that is stored locally. Do not save the file. Note: Some emphasized items appear bold online.

Shell Prompts in Command Examples

The following table shows the default UNIX® system prompt and superuser prompt for the C shell, Bourne shell, and Korn shell.

Table P–10 Shell Prompts


Shell	Prompt
C shell	`machine_name%`
C shell for superuser	`machine_name#`
Bourne shell and Korn shell	`$`
Bourne shell and Korn shell for superuser	`#`

Product Training

Sun Microsystems offers training in many Sun technologies through a variety of instructor-led courses and self-paced courses. For information about the training courses that Sun offers and to enroll in a class, visit Sun Training at http://training.sun.com/.