Perform this procedure for each non-global zone that you create in the cluster.
For complete information about installing a zone, refer to System Administration Guide: Solaris Containers-Resource Management and Solaris Zones.
You can configure a Solaris 10 non-global zone, simply referred to as a zone, on a cluster node while the node is booted in either cluster mode or in noncluster mode.
If you create a zone while the node is booted in noncluster mode, the cluster software discovers the zone when the node joins the cluster.
If you create or remove a zone while the node is in cluster mode, the cluster software dynamically changes its list of zones that can master resource groups.
Perform the following tasks:
Plan your non-global zone configuration. Observe the requirements and restrictions in Guidelines for Non-Global Zones in a Cluster.
Have available the following information:
The total number of non-global zones that you will create.
The public adapter and public IP address that each zone will use.
The zone path for each zone. This path must be a local file system, not a cluster file system or a highly available local file system.
One or more devices that should appear in each zone.
(Optional) The name that you will assign each zone.
If you will assign the zone a private IP address, ensure that the cluster IP address range can support the additional private IP addresses that you will configure. Use the cluster show-netprops command to display the current private-network configuration.
If the current IP address range is not sufficient to support the additional private IP addresses that you will configure, follow the procedures in How to Change the Private Network Configuration When Adding Nodes or Private Networks to reconfigure the private IP address range.
For additional information, see Zone Components in System Administration Guide: Solaris Containers-Resource Management and Solaris Zones.
Become superuser on the node on which you are creating the non-global zone.
You must be in the global zone.
If services are not yet online for a node, wait until the state becomes online before you proceed to the next step.
phys-schost# svcs multi-user-server STATE STIME FMRI online 17:52:55 svc:/milestone/multi-user-server:default
Configure, install, and boot the new zone.
Follow procedures in the following documentation:
Verify that the zone is in the ready state.
phys-schost# zoneadm list -v ID NAME STATUS PATH 0 global running / 1 my-zone ready /zone-path
(Optional) Assign a private IP address and a private hostname to the zone.
The following command chooses and assigns an available IP address from the cluster's private IP address range. The command also assigns the specified private hostname, or host alias, to the zone and maps it to the assigned private IP address.
phys-schost# clnode set -p zprivatehostname=hostalias node:zone
Specifies a property.
Specifies the zone private hostname, or host alias.
The name of the node.
The name of the non-global zone.
Perform the initial internal zone configuration.
Follow the procedures in Performing the Initial Internal Zone Configuration in System Administration Guide: Solaris Containers-Resource Management and Solaris Zones. Choose either of the following methods:
Log in to the zone
Use an /etc/sysidcfg file
You must make these changes to enable the zone to resolve searches for cluster-specific hostnames and IP addresses.
Log in to the zone.
phys-schost# zogin -c zonename
Open the /etc/nsswitch.conf file for editing.
phys-schost# vi /etc/nsswitch.conf
Add the cluster switch to the beginning of the lookups for the hosts and netmasks entries.
The modified entries would appear similar to the following:
… hosts: cluster files nis [NOTFOUND=return] … netmasks: cluster files nis [NOTFOUND=return] …
To install an application in a non-global zone, use the same procedure as for a standalone system. See your application's installation documentation for procedures to install the software in a non-global zone. Also see Adding and Removing Packages and Patches on a Solaris System With Zones Installed (Task Map) in System Administration Guide: Solaris Containers-Resource Management and Solaris Zones.
To install and configure a data service in a non-global zone, see the Sun Cluster manual for the individual data service.