The Start_failed resource state indicates that a Start or Prenet_start method failed or timed out on a resource, but its resource group came online anyway. The resource group comes online even though the resource has been placed in a faulted state and might not be providing service. This state can occur if the resource's Failover_mode property is set to None or to another value that prevents the failover of the resource group.
Unlike the Stop_failed resource state, the Start_failed resource state does not prevent you or the Sun Cluster software from performing actions on the resource group. You need only to execute a command that restarts the resource.
Use any one of the following procedures to clear this condition.
Perform this procedure from any cluster node.
Ensure that the following conditions are met:
You have the following information:
The name of the resource group that you are switching over
The name of the node or zone on which to switch over the resource group
The nodes or zones where the resource group is to be brought online or to remain online are in the cluster .
On a cluster member, become superuser or assume a role that provides solaris.cluster.modify RBAC authorization.
Switch the resource group to the new node or zone.
# clresourcegroup switch [-n node-zone-list] resource-group |
Specifies a comma-separated, ordered list of nodes or zones that can master this resource group. This resource group is switched offline on all of the other nodes. The format of each entry in the list is node:zone. In this format, node specifies the node name and zone specifies the name of a non-global Solaris zone. To specify the global zone, or to specify a node without non-global zones, specify only node.
This list is optional. If you omit this list, the resource group is switched on all nodes in the resource group's node list.
Specifies the name of the resource group to switch.
If any resource group that you are switching declares a strong affinity for other resource groups, the attempt to switch might fail or be delegated. For more information, see Distributing Online Resource Groups Among Cluster Nodes.
Verify that the resource group has been switched to the new node or zone and that the Start_failed resource state is cleared.
# clresourcegroup status |
The output from this command indicates the state of the resource and the resource group that has been switched over.
This example shows how to clear a Start_failed resource state that has occurred on the rscon resource in the resource-group-1 resource group. The command clears this condition by switching the resource group to the global zone phys-schost-2 .
To verify that the resource is in the Start_failed resource state on phys-schost-1, the following command is run:
# clresource status === Cluster Resources === Resource Name Node Name Status Message -------------- ---------- ------- ------- rscon phys-schost-1 Faulted Faulted phys-schost-2 Offline Offline hastor phys-schost-1 Online Online phys-schost-2 Offline Offline |
To perform the switch, the following command is run:
# clresourcegroup switch -n phys-schost-2 resource-group-1 |
To verify that the resource group is switched to be online on phys-schost-2 and that the Start_failed resource status is cleared, the following command is run:
# clresource status === Cluster Resources === Resource Name Node Name Status Message -------------- ---------- ------- ------- rscon phys-schost-1 Offline Offline phys-schost-2 Online Online hastor phys-schost-1 Online Online phys-schost-2 Offline Offline |
The clresourcegroup(1CL) man page.
Perform this procedure from any cluster node.
Ensure that the following conditions are met:
You have the following information:
The name of the resource group that you are restarting
The name of the node on which to restart the resource group
The nodes or zones where the resource group is to be brought online or to remain online are cluster nodes.
On a cluster member, become superuser or assume a role that provides solaris.cluster.modify RBAC authorization.
Restart the resource group.
# clresourcegroup restart -n node resource-group |
Specifies the name of the node on which the resource group is to be restarted. This resource group is switched offline on all of the other nodes.
Specifies the name of the resource group to restart.
Verify that the resource group has been restarted on the new node and that the Start_failed resource state is cleared.
# clresourcegroup status |
The output from this command indicates the state of the resource and the resource group that has been restarted.
This example shows how to clear a Start_failed resource state that has occurred on the rscon resource in the resource-group-1 resource group. The command clears this condition by restarting the resource group on the global zone phys-schost-1 .
To verify that the resource is in the Start_failed resource state on phys-schost-1, the following command is run:
# clresource status === Cluster Resources === Resource Name Node Name Status Message -------------- ---------- ------- ------- rscon phys-schost-1 Faulted Faulted phys-schost-2 Offline Offline hastor phys-schost-1 Online Online phys-schost-2 Offline Offline |
To restart the resource, the following command is run:
# clresourcegroup restart -n phys-schost-1 –g resource-group-1 |
To verify that the resource group is restarted on phys-schost-1 and that the Start_failed resource status is cleared, the following command is run:
# clresource status === Cluster Resources === Resource Name Node Name Status Message -------------- ---------- ------- ------- rscon phys-schost-1 Offline Offline rscon phys-schost-2 Online Online hastor phys-schost-1 Online Online hastor phys-schost-2 Offline Offline |
The clresourcegroup(1CL) man page.
Perform this procedure from any cluster node.
Ensure that you have the name of the resource that you are disabling and enabling.
On a cluster member, become superuser or assume a role that provides solaris.cluster.modify RBAC authorization.
Disable and then enable the resource.
# clresource disable resource # clresource enable resource |
Specifies the name of the resource.
Verify that the resource has been disabled and enabled and that the Start_failed resource state is cleared.
# clresource status |
The output from this command indicates the state of the resource that has been disabled and re-enabled.
This example shows how to clear a Start_failed resource state that has occurred on the rscon resource by disabling and enabling the resource.
To verify that the resource is in the Start_failed resource state, the following command is run:
# clresource status === Cluster Resources === Resource Name Node Name Status Message -------------- ---------- ------- ------- rscon phys-schost-1 Faulted Faulted phys-schost-2 Offline Offline hastor phys-schost-1 Online Online phys-schost-2 Offline Offline |
To disable and re-enable the resource, the following commands are run:
# clresource disable rscon # clresource enable rscon |
To verify that the resource is re-enabled and that the Start_failed resource status is cleared, the following command is run:
# clresource status === Cluster Resources === Resource Name Node Name Status Message -------------- ---------- ------- ------- rscon phys-schost-1 Online Online phys-schost-2 Offline Offline hastor phys-schost-1 Online Online phys-schost-2 Offline Offline |
The clresource(1CL) man page.