Install Windows Server 2003 Operating System

C H A P T E R 2

This chapter provides information about installing the Windows Server 2003 Operating System (OS).

Note - If you are planning to create a RAID set on your disk, the recommended procedure is to create a hardware RAID before you install the OS. For more information, see the Sun Disk Management Overview, For x64 Sun Fire and Sun Blade Series Servers (820-6350)

This chapter includes the following topics:

Task Map for the Windows Server 2003 Installation

Boot-Time Device Drivers

Prepare Mass-Storage Drivers for Delivery

Install Windows Server 2003 Using Local or Remote Media

Install Windows Server 2003 via PXE Network Environment

Task Map for the Windows Server 2003 Installation

Use TABLE 2-1 To preview the installation process defined as a series of tasks. The table identifies the tasks required and provides pointers to the instructions for performing that task.

TABLE 2-1 T ask Map for the Windows Server 2003 Installation
Step	Task	Description	Relevant Topic(s)
1	Review installation prerequisites	Verify that all applicable requirements are met for installing an operating system to a server.	TABLE 1-2 OS Installation Prerequisites
2	Choose an installation method	Evaluate and select an installation method that meets the needs of your infrastructure.	Installation Methods
3	Ensure that the BIOS factory defaults are set	Verify that the factory default settings in the BIOS are set prior to performing the operating system installation.	Verifying BIOS Settings for New Installations
4	Gather the Windows installation media	The Windows OS is shipped with the CD and DVD media and documentation that you will need to install the Windows OS.	You can download or order the media for Windows 2003 at `http://www.microsoft.com`
5	Download server-specific drivers or obtain drivers from Tools and Driver CD	Depending on your system, some device drivers are required to be installed at boot time. You can obtain these drivers from the Sun download site or from the Tools and Drivers CD/DVD.	Download the Server-Specific Drivers
6	Prepare mass-storage drivers	Produce the mass-storage drivers floppy required for the Windows 2003 installation.	Prepare Mass-Storage Drivers for Delivery
7	Perform the Windows OS installation	Follow the instructions in this chapter to install the Windows 2003 operating system.	Install Windows Server 2003 Using Local or Remote Media Install Windows Server 2003 via PXE Network Environment
8	Install driver(s) and post supplemental software, post installation, if necessary.	If the Windows operating system does not include the necessary device drivers to support your system, you may need to install additional device drivers. If your system includes RAID controllers, you may need to install supplemental software to support these controllers.	Post Installation
9	Enable Wake On LAN feature, if appropriate	If required, you can enable the Wake On LAN feature for this server.	Post Installation

Note - The complete Microsoft Windows operating system installation process is not documented in this section. This section describes the steps for booting the Windows Server 2003 media, installing drivers (if necessary) at boot, and partitioning the drive. For additional information, consult the Microsoft Windows 2003 product documentation at http://www.microsoft.com/windowsserver2003/proddoc/default.mspx

Boot-Time Device Drivers

TABLE 2-2 identifies the device drivers that you may need to install at boot time while performing the Windows Server 2003 installation.

TABLE 2-2 Windows 2003 Server-specific Drivers Installed at Boot Time
Device Driver	Description
Intel SATA Driver	The Intel SATA device driver must be available at boot time if installing to a local SATA hard disk drive (HDD).
LSI SAS/SATA RAID Driver	The LSI SAS/SATA device driver must be available at boot time if installing to a local SAS or SATA hard disk drive (HDD).
Sun StorageTek SAS/SATA RAID Driver	The Sun StorageTek SAS/SATA device driver must be available at boot time if installing to a local SAS or SATA hard disk drive (HDD).
QLogic SAN Driver	The QLogic Fibre Channel (FC) device driver must be installed at installation boot time if your installation target is a QLogic FC Storage Area Network (SAN) device.
Emulex SAN Driver	The Emulex FC device driver must be installed at installation boot time if your installation target is a Emulex FC SAN device.

The boot-time device drivers listed in TABLE 2-2 are included on the Tools and Drivers CD/DVD that ships with the server. However, if you do not have the Tools and Drivers CD/DVD, you can download these same drivers from the Sun download site. For instructions on downloading the server-specific drivers package, which includes the boot-time device drivers, see Downloading Server-Specific Drivers.

Prepare Mass-Storage Drivers for Delivery

This section contains instructions on preparing the necessary mass-storage drivers media for a local or remote Windows Server 2003 installation.

You can choose to prepare the mass-storage drivers on a floppy disk or floppy image, see TABLE 2-3.

TABLE 2-3 Mass-Storage Driver Media Options
Media Option	Section to Read
Floppy Disk Local or Remote	Create Floppy Disk For Device Drivers
Floppy Image	Prepare Floppy Image For Device Drivers

Create Floppy Disk For Device Drivers

Perform the following procedure in this section if you have chosen to create a floppy disk to store the required Windows 2003 device drivers.

Before You Begin

Prior to performing the following procedure to create a floppy disk, ensure that the following requirements have been met:

The system being used to create the floppy disk is connected to a USB floppy drive

Floppy disk media is available

FloppyPack_x_x_x.zip file is available

You can obtain the FloppyPack_x_x_x.zip file on the Tools and Drivers CD/DVD or you can download it from the Sun download site. For instructions about how to download it from Sun, see Downloading Server-Specific Drivers.

Note - The _x_x_x number identifies the version of the package (for example, FloppyPack_1_1_4.zip).

Create Floppy Disk For Device Driver Installation

Sun provides a Sun Mass-Storage Driver Disk Creation wizard to help you create a floppy disk. Follow these steps to create a floppy disk using the Sun Mass-Storage Driver Disk Creation wizard.

1. Start the Sun Mass-Storage Driver Disk Creation wizard from one of the following media sources:

Tools and Driver CD

Perform the following steps to start the wizard:

a. Insert the Tools and Drivers CD/DVD into a Windows system with a CD/DVD drive.

The CD will start automatically.

b. At the main menu, select Make a Windows Server 2003 Mass-Storage Driver Disk, and then proceed to Step 2.

The Welcome page for the Mass-Storage Driver Disk Creation wizard appears.

FloppyPack_x_x_x.zip file (obtained from Sun download site)

Perform the following steps to copy and extract the files and start the wizard.

a. On a system running Microsoft Windows software with a floppy drive, copy the FloppyPack_x_x_x.zip file to a temporary directory.

b. Start Windows Explorer.

c. Navigate to the folder where you placed the downloaded file.

d. Select FloppyPack_x_x_x.zip.

e. On the File menu, click Extract All to extract the files into a new (empty) folder.

Note - If your version of Windows Explorer does not natively support compressed folders, use a third-party utility to extract the contents of the zip file. Make sure to maintain the directory structure of the folders after extracting them.

f. Start Windows Explorer and navigate to the folder containing the extracted files.

g. In Windows Explorer, open the directory containing the extracted files and double-click the mkfloppy.exe wizard, and then proceed to Step 2.

The Welcome page for the Mass-Storage Driver Disk Creation wizard appears.

2. In the Mass-Storage Driver Disk Creation wizard Welcome page, do the following:

a. Click Next and follow the instructions in the wizard to create the mass-storage driver floppy disk for your server.

b. Insert a blank floppy disk into drive A: when prompted.

The Format 3 1/2 Floppy dialog appears.

Graphic showing the Mass-Storage Driver Creator wizard.

3. In the Format 3 1/2 Floppy dialog, click the Start button to begin formatting.

Graphic showing the Format 3 1/2 Floppy dialog.

4. When the floppy disk formatting completes, click the Close button.

The Format 3 1/2 Floppy page closes and you are returned to the Mass-Storage Driver Disk Creation wizard.

5. Click Next and follow the instructions in the wizard to complete the creation of the mass-storage driver floppy disk.

6. Proceed to Install Windows Server 2003 Using Local or Remote Media.

Prepare Floppy Image For Device Drivers

Perform the following procedure in this section if you have chosen to use the floppy image media to install the required Windows 2003 device drivers.

Before You Begin

Prior to performing the following procedure to prepare the floppy image for device driver installation, ensure that the following requirements have been met:

Obtain FloppyPack_x_x_x.zip driver package from the Tools and Drivers CD/DVD or from the Sun download site as described in Downloading Server-Specific Drivers

The system hosting the Sun ILOM Remote Console must have local or network access to the FloppyPack_x_x_x.zip driver package.

Prepare Floppy Image For Device Driver Installation

1. Obtain the floppy image file containing the device drivers from one of the following media sources:

Tools and Drivers CD/DVD

Perform these steps to access the floppy package:

a. Insert the CD into the Sun ILOM Remote Console system.

b. Navigate to the following directory:

windows\w2k3\packages\FloppyPack\image

c. Proceed to Step 2.

FloppyPack.zip file (from the Sun download site)

a. Copy the FloppyPack_x_x_x.zip file to a temporary directory.

b. Start Windows Explorer.

c. Navigate to the temporary folder where you placed the downloaded file.

d. Select FloppyPack_x_x_x.zip.

e. On the File menu, click Extract All to a new empty folder.

f. Navigate to the image folder where the extracted files reside then proceed to Step 2.

2. Copy the appropriate floppy image file to a local or network shared location where the Sun ILOM Remote Console system can access it during the Windows installation (for example, intelsmilsi.img).

For instructions for enabling image file media redirection in the Sun ILOM Remote Console, see the Sun Integrated Lights Out Manager 2.0 User’s Guide.

3. Proceed to Install Windows Server 2003 Using Local or Remote Media.

Install Windows Server 2003 Using Local or Remote Media

The following procedure describes how to boot the Windows Server 2003 operating system from local or remote media. It assumes you are booting the Windows installation media from one of the following sources:

Windows CD or DVD (internal or external CD/DVD)

Windows 2003 ISO image (network repository)

Note - If you are booting the installation media from a PXE environment, refer to Install Windows Server 2003 via PXE Network Environment for instructions.

Before You Begin

Prior to performing the installation, the following requirements must be met:

All applicable installation prerequisites for installing an operating system should have been met. For further information about these prerequisites, see TABLE 1-2 OS Installation Prerequisites.

An installation method (for example: console, boot media, and installation target) should have been chosen and established prior to performing the installation. For more information about these setup requirements, see Installation Methods.

After completing this procedure, you will need to perform the post installation tasks as described in Post Installation.

Install Windows Server 2003 Using Local or Remote Media

1. Ensure that the installation media is available to boot.

Note - For the Sun Fire X4275 server, which has neither a CD/DVD-ROM drive nor a USB connector on the front panel, use the Sun ILOM Remote Console to redirect the boot media from a remote storage device. For instructions, see instructions for Remote Boot Media in TABLE 1-4 Boot Media Options for Performing the OS Installation.

For example:

For distribution CD/DVD--Insert the Windows 2003 Distribution media (CD labeled #1 or the single DVD) into the local or remote USB CD/DVD-ROM drive.

For ISO image--Ensure that the ISO images are available and that the ILOM Remote Console application is aware of the first ISO image location.

For additional information about how to set up the installation media, see TABLE 1-4 Boot Media Options for Performing the OS Installation.

2. Reset the power on the server.

For example:

From the ILOM web interface, select the Remote Control --> Remote Power Control tab, then select the Power Cycle option from the Host action drop-down list box.

From the local server, press the Power button (approximately 1 second) on the front panel of the server to power off the server, then press the Power button again to power on the server.

For further details for powering on or off your server, see the Sun Fire X4170, X4275, and X4275 Servers Service Manual.

From the ILOM CLI, type: reset /SYS

The BIOS screen appears.

BIOS Boot screen.

3. When the Press F8 for BBS POPUP prompt appears on the BIOS POST screen, press F8.

The BBS POPUP menu allows you to select a boot device.

4. Once the BIOS POST process is complete, the Boot Device menu appears.

Note - The screen that appears in your installation may be different depending on the type of disk controller installed in your server.

Graphic showing the boot device select screen.

5. In the Boot Device menu, select a boot device based on the Windows media installation method you elected to use and press Enter.

For example:

If you elected to use the Windows local delivery method, select CD/DVDW.

If you elected to use the ILOM Remote Console method, select Virtual CDROM.

6. When prompted with Press any key to boot from CD, quickly press any key.

The Windows Setup process begins.

7. When you see the following prompt at the bottom of the Windows Setup dialog, quickly press F6:

Press F6 if you need to install a third party SCSI or RAID driver.

Note - The above prompt lasts for approximately five seconds and is easy to miss. If you do not press F6 while the prompt is displayed, the dialog allowing you to specify additional drivers is not displayed and the installation will fail. If this happens, restart the server on which you are performing the installation and go back to Step 3.

After pressing F6, the setup process continues and the following dialog appears. This dialog gives you the option of specifying additional mass-storage devices.

Screen shot of Specify Additional Device screen

8. Make sure that the mass-storage drivers are accessible according to the mass-storage driver installation method that you have selected.

For example:

For Floppy Disk Local--Mass-storage drivers floppy disk in floppy drive A on the server.

For Floppy Disk Remote--Mass-storage drivers floppy disk in the Sun ILOM Remote Console system floppy drive.

For Floppy Image--Use the floppy image file accessible from the Sun ILOM Remote Console system (for example, intelsmilsi.img).

9. Press S to specify additional devices.

A dialog appears listing the available drivers.

Screenshot of Select SCSI Adapter screen.

Note - The above dialog will vary depending on the type of mass-storage controller driver(s) you are installing.

10. In the Select Adapter dialog, select the appropriate mass-storage controller driver version (Windows 32-bit or 64-bit) that you are installing, then press Enter.

For example:

For servers with an LSI-based integrated RAID controller, select:
LSI Logic Fusion-MPT SAS Driver (32-bit or 64-bit)

For servers with an Adaptec-based integrated RAID controller, select:
Adaptec SAS/SATA-II RAID Driver (32-bit or 64-bit)

For servers with an Intel-based integrated disk controller, select:
Intel(R) ICH10R SATA AHCI Controller (32-bit or 64-bit)

A dialog similar to the following appears stating that the setup will load support for the specified mass-storage device.

Graphic showing the mass storage device support screen.

11. Press Enter to continue.

The Windows setup process continues and a Setup Notification dialog appears.

Graphic showing the setup notification screen.

12. At the Setup Notification dialog, press Enter to continue.

The Welcome to Setup dialog appears.

Graphic showing the setup welcome screen.

13. At the Welcome to Setup dialog, press Enter to continue.

The Windows Licensing Agreement dialog appears.

14. To accept the license agreement, press F8.

A dialog appears that shows the existing partitions on the server and the unpartitioned space.

Note - Any previous installations on the server’s boot disk will cause the partitioning dialog to appear.

Graphic showing the existing partitions screen.

15. To delete the existing partition, press D.

A confirmation dialog appears to verify that you really want to delete the partition.

16. Press Enter to continue.

Another confirmation dialog with a caution notice appears and describes the partition that you are about to delete.

17. Press L to delete the partition.

The partition is deleted and the a dialog appears that shows the unpartitioned space on the server’s disk.

18. To create a partition in the unpartitioned space, press C.

A dialog appears that allows you to specify the size of the new partition.

Graphic showing the partition size specification screen.

19. Either accept the default size of the partition to be created or use the Back Space key to delete the size specified and enter a new size and press Enter.

A recommended size of 40,000 megabytes is usually sufficient for a Windows installation. This will leave adequate space on the disk for installations of other media.

A partition confirmation windows appears.

20. Press Enter to accept the partition.

A partition formatting dialog appears.

Graphic showing the partition format selection screen.

21. Use the up and down arrow keys to select the <Quick> menu option and press Enter to format the partition.

The setup process formats the partition and copies the files to the Windows installation folders. This process might take several minutes

22. Follow the on-screen instructions to complete the initial setup of Windows Server 2003 until you are prompted with the following message:

Remove disks or other media. Press any key to restart.

When this message appears you will need to complete one of the following steps, depending on which driver delivery method you have chosen, to complete the installation:

Floppy Disk Local--Remove the floppy disk from the floppy drive on the server.

Floppy Disk Remote--Remove the floppy disk from the Sun ILOM Remote Console system.

Floppy Image--Deselect Floppy Image from the Sun ILOM Remote Console Devices menu.

Then, press any key to restart the system and complete the Windows Server 2003 Installation.

23. Proceed to Post Installation.

Install Windows Server 2003 via PXE Network Environment

This section explains the initial information you will need to install the Windows Server 2003 operating system software over an established PXE-based network via a customer-provided Windows 2003 Remote Installation Services (RIS) image.

Note - As an alternative, you can install the Windows 2003 operating system over an established PXE-based network via a customer-provided Windows Deployment Services (WDS) image.

After completing this procedure, you will need to perform the post installation tasks as described in Post Installation.

Before You Begin

The following requirements must be met prior to performing the Windows Server 2003 installation from a RIS image.

To use PXE to boot the installation media over the network:

Configure the network (NFS, FTP, HTTP) server to export the installation tree.

Configure the files on the TFTP server that are necessary for PXE booting.

Configure the Sun server MAC network port address to boot from the PXE configuration.

Configure DHCP

To use a RIS image to perform the installation:

Create the RIS installation image.

Follow the RIS installation instructions in the Windows Server 2003 documentation.

Add the required system device drivers to the RIS installation image.

For instruction, see Appendix A Incorporate Sun Fire Server Drivers Into WIM or RIS Images.

RIS Administrator password.

Install Windows Server 2003 via PXE

1. Ensure that the PXE network environment is properly set up and the Windows Server 2003 installation media is available for PXE boot.

Note - Information concerning how to properly set up and deploy a RIS network environment is outside the scope of this installation guide. For these details, see Microsoft’s documentation for deploying and using Remote Installation Services.

2. Reset the power on the server.

For example:

From the ILOM web interface, select the Remote Control --> Remote Power Control tab, then select the Power Cycle option from the Host action drop-down list box.

From the local server, press the Power button (approximately 1 second) on the front panel of the server to power off the server, then press the Power button again to power on the server.

For further details for powering on or off your server, see the Sun Fire X4170, X4275, and X4275 Servers Service Manual.

From the ILOM CLI, type: reset /SYS

The BIOS screen appears.

BIOS Boot screen.

Note - The next events occur very quickly, so focused attention is needed for the following steps. Watch carefully for these messages as they appear on the screen for a brief time. You might want to enlarge the size of your screen to eliminate scroll bars.

3. Press F8 to specify a temporary boot device.

The Please Select Boot Device menu appears.

4. In the Please Select Boot Device menu, select the appropriate PXE installation boot device and press Enter.

The PXE installation boot device is the physical network port configured to communicate with your network installation server.

Note - The boot device options shown on the following Select Boot Device dialog may be different from the options listed on your screen.

PXE boot device screen.

The Boot Agent dialog appears.

Graphic showing the Boot Agent dialog.

5. In the Boot Agent dialog, press F12 for a network service boot.

The Welcome to Client Installation wizard appears.

Graphic showing the Client Installation Wizard Welcome screen.

6. In the Welcome to Client Installation wizard, press Enter to continue.

The next dialog prompts you for a user name, password, and domain name.

Graphic showing the Client Installation Wizard user name and password dialog.

7. In the user name and password dialog, specify your user name and password, then press Enter.

Use the Tab key to move between fields.

The Windows Server 2003 version dialog appears.

Graphic showing the Client Installation Wizard 32-bing/64-bin option screen.

8. In the Windows Server 2003 version dialog, select the version (32-bit or 64-bit) you are installing, then press Enter.

The Windows Server 2003 operating system choice dialog appears.

9. In the OS choice dialog, select the OS option you are installing, then press Enter.

Note - The OS choice dialog identifies the names of the OS images that are available for you to install from your RIS server. The OS choice dialog from your RIS server will list different options from the ones shown in the example dialog below.

A Caution dialog appears.

Graphic showing the Client Installation Wizard Caution screen.