Switch Overview - Sun Network 10GbE Switch 72p

Skip Navigation Links
Exit Print View
	Sun Network 10GbE Switch 72p User’s Guide

Oracle Technology Network

Document Information

Using This Documentation

Related Documentation

CLI Command Modes

Support and Accessibility

Understanding the Switch

Switch Overview

Front Panel Components

Rear Panel Components

Confirming Switch Specifications

Physical Specifications

Electrical Specifications

Environmental Specifications

Acoustic Noise Emissions

Installing the Switch

Preparing to Install the Switch

Verify Shipping Kit Contents

Antistatic Precautions

Install the Switch in the Rack

Connecting Management Cables

Management Cable Requirements

Connect the NET MGT Cable

Connect the SER MGT Cable

Powering On the Switch

Power Cord Specifications

Power On the Switch

Connecting Ethernet Cables

Splitter Cables

Ethernet Cable Cautions

Connect Ethernet Cables

Finish the Switch Installation

Administering the Switch

Connecting to the Service Processor

Oracle ILOM Overview

Oracle ILOM Features Not Supported

Verify the DHCP-Assigned IP Address and Host Name

Configure Network Management From CLI (SER MGT)

Log Into Oracle ILOM Web (NET MGT)

Log Into Oracle ILOM CLI (NET MGT)

Log Into Oracle ILOM CLI (SER MGT)

SER MGT Port Configuration Parameters

Configure Network Management From Web

Configure Network Management From CLI (NET MGT)

Log Out of ILOM

Configuring SEFOS User Privileges

Create a SEFOS User

Change a SEFOS User Privilege Level

Update the Firmware

Connecting to SEFOS

Connect to SEFOS

Disconnect From SEFOS

Servicing the Switch

Troubleshooting the Switch

Identifying LEDs

Sensors Overview

Check Switch Status (LEDs)

Check Switch Status (Oracle ILOM)

Component Sensor Targets

Motherboard Sensor Targets

Understanding Service Procedures

Tools Needed for Service

Replaceable Components

Servicing Power Supplies

Power Off a Power Supply

Remove a Power Supply

Install a Power Supply

Power On a Power Supply

Servicing Ethernet Cables

Remove an Ethernet Cable

Install an Ethernet Cable

Servicing the Battery

Remove the Battery

Install the Battery

Switch Overview

Feature	Specifications
Management	MPC8547E processor (service processor) 1 GB DDR2 SDRAM SORDIMM, 512 MB NOR flash memory, and 2 GB NAND Flash memory Oracle ILOM firmware
Management interfaces	10/100BASE-T Ethernet I²C
Ports/connectors	Two NET MGT ports and one SER MGT port (RJ-45). Use NET MGT 0, Port A only. (See NET MGT Port) Eight SFP+ ports that support the SFP+ SR, LR, and LR-M modules 16 QSFP connectors on the switch with four 10GbE ports each supporting a total of 64 10 Gbps interfaces
Server interface (per server)	One XAUI interface to a switch port
Indicators/controls	SFP+ 10GbE Link Status/Activity (bifunctional) QSFP 10GbE Link Status/Activity (bifunctional) Front panel Locate, System Fault/Alarm, System OK LEDs Rear panel power supply and fan module status LEDs
Health	Voltage monitoring Temperature monitoring Fault detection and reporting
Power supplies	The switch has two redundant power supplies. The switch requires only one functional power supply to operate without errors. Note - The System OK LED goes into the off state if one of the power supplies is unplugged or offline. 3.3 VAUX from switch midplane 12 V from switch midplane
Cooling	The switch has five fans and requires three fully operational fans to avoid possible thermal errors. Airflow can be established with two different configurations, depending on where you choose to locate the front I/O connectors. To place the I/O connectors in the cold aisle (airflow from front to the rear), use Fan Module 350-1335. To place the I/O connectors in the hot aisle (airflow from rear to the front), use Fan Module 350-1312.

Related Information

Copyright © 2011, 2012 , Oracle and/or its affiliates. All rights reserved. Legal Notices

Previous

Next