JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Sun Server X2-8 Product Documentation
search filter icon
search icon

Document Information

Using This Documentation

Sun Server X2-8 Name Change

Product Downloads

Get Software and Firmware Downloads

Documentation and Feedback

About This Documentation

Change History

Hardware Installation and Product Notes

Product Notes

Overview of the Sun Server X2-8 Product Notes

Supported Software and Firmware

Hardware Issues

Oracle Solaris Operating System Issues

Linux Issues

Oracle VM Issues

Windows Operating System Issues

ESX Issues

Oracle ILOM Issues

BIOS Issues

Oracle Hardware Installation Assistant

Documentation Errata

Requesting Physical Media

Hardware Installation

Installation Overview

Front and Back Features and Components

Unpacking the Server and Identifying the Rack Mounting Hardware

Installing the Server In the Rack Using the Standard Rack Mounting Kit

Installing the Server in the Rack Using the Universal Rack Mounting Kit

Removing the Server from the Rack

Cabling and Power

Getting Service for Your Server

Determining Your Server Management Strategy

Configuring the Preinstalled Solaris Operating System

Configuring the Preinstalled Oracle Linux Operating System

Configuring the Preinstalled Oracle VM Software

Communicating With Oracle ILOM and the System Console

I/O and Interrupt Resource Allocation

Sun Server X2-8 Specifications

Requesting Physical Media

Operating System Installation

Oracle Solaris Operating System

Introduction to Oracle Solaris OS Installation

Preparing for OS Installation

Creating a Virtual Disk

Installing Solaris OS

Linux

Linux Installation Task Map

Oracle Hardware Installation Assistant (OHIA)

Task Overview

Obtaining OHIA

Preparing for OS Installation

How to Erase Your Boot Hard Disk

Creating a Virtual Disk

How to Create a Virtual Disk

About Using the x2APIC Option

Selecting a Media Delivery Method

Local Installation by Accessing the Console Using the Serial or Video Port

How to Configure the Serial Port

Remote Installation by Accessing the Console Using Oracle ILOM

How to Access the Server Console Using Oracle ILOM Web Interface

How to Access the Server Console Using the Oracle ILOM CLI Interface

Installing Oracle Linux

Installing Oracle Linux From Distribution Media

How to Download Oracle Linux Media

How to Install Oracle Linux From Distribution Media

Updating Oracle Linux

How to Update the Oracle Linux Operating System

Installing Red Hat Enterprise Linux

Installing RHEL From Distribution Media

How to Download RHEL Media Kits

How to Install RHEL From Distribution Media

Updating RHEL

How to Update the RHEL Operating System

How to Update the RHEL Drivers

Installing SUSE Linux Enterprise Server

Installing SLES From Distribution Media

How to Download SLES Media Kits

How to Install SLES From Distribution Media

Updating SLES

How to Update the SLES Operating System

How to Update the SLES Drivers

Configuring a Linux Server to Support PXE Installation

Overview of PXE

How to Install and Configure a DHCP Server for PXE

How to Install Portmap on Your PXE Server

How to Configure the TFTP Service on Your PXE Server

How to Configure PXELINUX on Your PXE Server

How to Configure the NFS Service on Your PXE Server

Disabling the Firewall

How to Disable the Firewall for SUSE Linux

How to Disable the Firewall for Oracle Linux or Red Hat Enterprise Linux

How to Create a PXE Installation Image for Oracle Linux

How to Create a PXE Installation Image for RHEL

How to Create a PXE Installation Image for SLES

How to Create a PXE Installation Image for Oracle VM

How to Install Linux From a PXE Server

Identifying Logical and Physical Network Interface Names for Linux OS Configuration

How to Identify Installed Network Ports

How to Identify Logical and Physical Network Interface Names While Installing Oracle Linux or RHEL

How to Identify Logical and Physical Network Interface Names While Installing SLES

Windows

Windows Server OS Installation Planning

Preparing For Windows OS Installation

Oracle Hardware Installation Assistant (OHIA)

Downloading Server Software

Configuring a Remote Console

Creating a Virtual Disk

Installing Windows Server

Updating Critical Drivers and Installing Supplemental Software

Incorporating Windows Server 2008 Device Drivers Into WIM Images for WDS

Identifying Network Interfaces in Windows

Oracle VM

Introduction to Oracle VM Installation

Preparing for OS Installation

Installing Oracle VM

ESX

Installing VMware ESX 4.1

Installing VMware ESXi 4.1 and ESXi 5 Installable

Booting From OS Distribution Media

Administration, Diagnostics, and Service

ILOM Supplement

Determining Your Server Management Strategy

Oracle ILOM Documentation

Updating Firmware

Server-Specific Oracle ILOM Features

Identifying and Clearing Faults

Recovering a Lost Oracle ILOM Password

Monitoring Hardware and Environmental Sensors

Diagnostics Guide

Overview of the Diagnostics Guide

Introduction to System Diagnostics

Troubleshooting the Server

Troubleshooting DIMM Problems

BIOS POST

Using Oracle ILOM to Monitor the Host

Creating a Data Collector Snapshot

Using SunVTS Diagnostics Software

Performing Pc-Check Diagnostic Tests

U-Boot Diagnostic Start-Up Tests

Service Manual

Sun Server X2-8 Service Manual Overview

Server and Component Overview

Power and Reset

Removing and Installing Components

Sun Server X2-8 Service Procedures and Information

Sun Server X2-8 Specifications

Requesting Physical Media

Index

How to Create a PXE Installation Image for Oracle VM

At the release of this document, Oracle VM 2.2.1 is the minimum supported version of Oracle VM. These instructions are for creating a PXE installation image of Oracle VM server.

Before You Begin

The PXE installation procedure requires the following items:

  1. Set up the directory structure that will hold the Oracle VM Server software.
    # mkdir -p /home/pxeboot/ovm_svr_2.2/
  2. Enter the following commands to copy the contents of each OVM distribution CD to the appropriate PXE subdirectory:

    Note - Eject and insert CDs only when the CD/DVD drive is unmounted.


    # mount dev/cdrom /mnt/cdrom
    # cp -r /mnt/cdrom/* /home/pxeboot/ovm_svr_2.2/
    # umount /mnt/cdrom

    If you are installing from a DVD, you have to do this only once. When the copy is done, proceed to the next step.

  3. Copy the vmlinuz and initrd.img files to the appropriate PXE target subdirectory:

    # cp /home/pxeboot/ovm_svr_2.2/images/pxeboot/vmlinuz /home/pxeboot/ovm_svr_2.2

    # cp /home/pxeboot/ovm_svr_2.2/images/pxeboot/initrd.img /home/pxeboot/ovm_svr_2.2

  4. Using a text editor, create a kickstart file (ks.cfg) in the following location on your PXE server:

    /home/pxeboot/ovm_svr_2.2/ks.cfg

  5. Add the necessary kickstart commands.

    If you know the required commands, type them in. Or, you can copy and insert the following content:

    lang en_US
    #langsupport en_US
    keyboard us
    #mouse genericusb
    timezone --utc America/Los_Angeles
    rootpw xxxx
    reboot
    bootloader --location=mbr
    install
    nfs --server n.n.n.n --dir /home/pxeboot/ovm_svr_2.2
    clearpart --all
    part /boot --fstype ext3 --size 512 --ondisk sda
    part  swap --size 4096 --ondisk sda
    part / --fstype ext3 --size 1 --grow --ondisk sda
    network --bootproto dhcp
    # password : abc123
    ovsagent --iscrypted Y2fEjdGT1W6nsLqtJbGUVeUp9e4=
    #ovsmgmntif eth0
    auth  --useshadow  --enablemd5
    firewall --disabled
    #Do not configure the X Window System
    skipx
    text
    
    %packages
    @Everything
    
    %pre
    
    %post --nochroot
    
    %post

    where n.n.n.n is the IP address of your PXE server. Ensure that the location indicated after --dir is pointing to the top level of your image.

  6. Save the kickstart file.
  7. Using a text editor, create the PXE configuration file (to be named default). This file defines the menu shown to the target system during network boot.

    The following example shows two labels for an Oracle VM menu:


    Note - Type the text block from append through ks.cfg as one continuous string with no returns.


    label ovm_svr_2.2 sda eth select
    kernel ovm_svr_2.2/images/pxeboot/vmlinuz
    append initrd=ovm_svr_2.2/images/pxeboot/initrd.img load_ramdisk=1 network 
    ks=nfs:n.n.n.n:/home/pxeboot/ovm_svr_2.2/ks.cfg mem=32g
    
    label ovm_svr_2.2 sda eth select serial console
    kernel ovm_svr_2.2/images/pxeboot/vmlinuz
    append initrd=ovm_svr_2.2/images/pxeboot/initrd.img load_ramdisk=1 network 
    ks=nfs:n.n.n.n:/home/pxeboot/ovm_svr_2.2/ks.cfg mem=32g 
    console=ttyS0,115200

    where n.n.n.n is the IP address of your PXE server.

  8. Save the file as default in the following location on the PXE server:

    /home/pxeboot/pxelinux.cfg/default