JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
System Administration Guide: IP Services     Oracle Solaris 10 8/11 Information Library
search filter icon
search icon

Document Information


Part I Introducing System Administration: IP Services

1.  Oracle Solaris TCP/IP Protocol Suite (Overview)

Part II TCP/IP Administration

2.  Planning Your TCP/IP Network (Tasks)

3.  Introducing IPv6 (Overview)

4.  Planning an IPv6 Network (Tasks)

5.  Configuring TCP/IP Network Services and IPv4 Addressing (Tasks)

6.  Administering Network Interfaces (Tasks)

7.  Configuring an IPv6 Network (Tasks)

8.  Administering a TCP/IP Network (Tasks)

9.  Troubleshooting Network Problems (Tasks)

10.  TCP/IP and IPv4 in Depth (Reference)

11.  IPv6 in Depth (Reference)


12.  About DHCP (Overview)

13.  Planning for DHCP Service (Tasks)

14.  Configuring the DHCP Service (Tasks)

15.  Administering DHCP (Tasks)

16.  Configuring and Administering the DHCP Client

17.  Troubleshooting DHCP (Reference)

18.  DHCP Commands and Files (Reference)

Part IV IP Security

19.  IP Security Architecture (Overview)

20.  Configuring IPsec (Tasks)

21.  IP Security Architecture (Reference)

IPsec Service Management Facility

ipsecconf Command

ipsecinit.conf File

Sample ipsecinit.conf File

Security Considerations for ipsecinit.conf and ipsecconf

ipsecalgs Command

Security Associations Database for IPsec

Utilities for Key Generation in IPsec

Security Considerations for ipseckey

IPsec Extensions to Other Utilities

ifconfig Command and IPsec

auth_algs Security Option

encr_auth_algs Security Option

encr_algs Security Option

snoop Command and IPsec

22.  Internet Key Exchange (Overview)

23.  Configuring IKE (Tasks)

24.  Internet Key Exchange (Reference)

25.  IP Filter in Oracle Solaris (Overview)

26.  IP Filter (Tasks)

Part V Mobile IP

27.  Mobile IP (Overview)

28.  Administering Mobile IP (Tasks)

29.  Mobile IP Files and Commands (Reference)


30.  Introducing IPMP (Overview)

31.  Administering IPMP (Tasks)

Part VII IP Quality of Service (IPQoS)

32.  Introducing IPQoS (Overview)

33.  Planning for an IPQoS-Enabled Network (Tasks)

34.  Creating the IPQoS Configuration File (Tasks)

35.  Starting and Maintaining IPQoS (Tasks)

36.  Using Flow Accounting and Statistics Gathering (Tasks)

37.  IPQoS in Detail (Reference)



ipsecconf Command

You use the ipsecconf command to configure the IPsec policy for a host. When you run the command to configure the policy, the system creates the IPsec policy entries in the kernel. The system uses these entries to check the policy on all inbound and outbound IP datagrams. Forwarded datagrams are not subjected to policy checks that are added by using this command. The ipsecconf command also configures the security policy database (SPD).

You must become superuser or assume an equivalent role to invoke the ipsecconf command. The command accepts entries that protect traffic in both directions. The command also accepts entries that protect traffic in only one direction.

Policy entries with a format of local address and remote address can protect traffic in both directions with a single policy entry. For example, entries that contain the patterns laddr host1 and raddr host2 protect traffic in both directions, if no direction is specified for the named host. Thus, you need only one policy entry for each host.

Policy entries with a format of source address to destination address protect traffic in only one direction. For example, a policy entry of the pattern saddr host1 daddr host2 protects inbound traffic or outbound traffic, not both directions. Thus, to protect traffic in both directions, you need to pass the ipsecconf command another entry, as in saddr host2 daddr host1.

To ensure that the IPsec policy is active when the machine boots, you can create an IPsec policy file, /etc/inet/ipsecinit.conf. This file is read when the network services are started. For instructions on how to create an IPsec policy file, see Protecting Traffic With IPsec (Task Map).

Starting in the Solaris 10 4/09 release, with the -c option, the ipsecconf command checks the syntax of the IPsec policy file that you provide as an argument.

Policy entries that are added by the ipsecconf command are not persistent over a system reboot. To ensure that the IPsec policy is active when the system boots, add the policy entries to the /etc/inet/ipsecinit.conf file. In the current release, refresh or enable the policy service. In a release prior to the Solaris 10 4/09 release, reboot or use the ipsecconf command. For examples, see Protecting Traffic With IPsec (Task Map).