JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle Solaris ZFS Administration Guide     Oracle Solaris 10 8/11 Information Library
search filter icon
search icon

Document Information

Preface

1.  Oracle Solaris ZFS File System (Introduction)

2.  Getting Started With Oracle Solaris ZFS

3.  Oracle Solaris ZFS and Traditional File System Differences

4.  Managing Oracle Solaris ZFS Storage Pools

5.  Installing and Booting an Oracle Solaris ZFS Root File System

6.  Managing Oracle Solaris ZFS File Systems

7.  Working With Oracle Solaris ZFS Snapshots and Clones

8.  Using ACLs and Attributes to Protect Oracle Solaris ZFS Files

9.  Oracle Solaris ZFS Delegated Administration

10.  Oracle Solaris ZFS Advanced Topics

ZFS Volumes

Using a ZFS Volume as a Swap or Dump Device

Using a ZFS Volume as a Solaris iSCSI Target

Using ZFS on a Solaris System With Zones Installed

Adding ZFS File Systems to a Non-Global Zone

Delegating Datasets to a Non-Global Zone

Adding ZFS Volumes to a Non-Global Zone

Using ZFS Storage Pools Within a Zone

Managing ZFS Properties Within a Zone

Understanding the zoned Property

Using ZFS Alternate Root Pools

Creating ZFS Alternate Root Pools

Importing Alternate Root Pools

ZFS Rights Profiles

11.  Oracle Solaris ZFS Troubleshooting and Pool Recovery

12.  Recommended Oracle Solaris ZFS Practices

A.  Oracle Solaris ZFS Version Descriptions

Index

ZFS Volumes

A ZFS volume is a dataset that represents a block device. ZFS volumes are identified as devices in the /dev/zvol/{dsk,rdsk}/pool directory.

In the following example, a 5-GB ZFS volume, tank/vol, is created:

# zfs create -V 5gb tank/vol

When you create a volume, a reservation is automatically set to the initial size of the volume so that unexpected behavior doesn't occur. For example, if the size of the volume shrinks, data corruption might occur. You must be careful when changing the size of the volume.

In addition, if you create a snapshot of a volume that changes in size, you might introduce inconsistencies if you attempt to roll back the snapshot or create a clone from the snapshot.

For information about file system properties that can be applied to volumes, see Table 6-1.

If you are using a Solaris system with zones installed, you cannot create or clone a ZFS volume in a non-global zone. Any attempt to do so will fail. For information about using ZFS volumes in a global zone, see Adding ZFS Volumes to a Non-Global Zone.

Using a ZFS Volume as a Swap or Dump Device

During installation of a ZFS root file system or a migration from a UFS root file system, a swap device is created on a ZFS volume in the ZFS root pool. For example:

# swap -l
swapfile                  dev    swaplo   blocks     free
/dev/zvol/dsk/rpool/swap 253,3        16  8257520  8257520

During installation of a ZFS root file system or a migration from a UFS root file system, a dump device is created on a ZFS volume in the ZFS root pool. The dump device requires no administration after it is set up. For example:

# dumpadm
      Dump content: kernel pages
       Dump device: /dev/zvol/dsk/rpool/dump (dedicated)
Savecore directory: /var/crash/t2000
  Savecore enabled: yes

If you need to change your swap area or dump device after the system is installed or upgraded, use the swap and dumpadm commands as in previous Solaris releases. If you need to create an additional swap volume, create a ZFS volume of a specific size and then enable swap on that device. For example:

# zfs create -V 2G rpool/swap2
# swap -a /dev/zvol/dsk/rpool/swap2
# swap -l
swapfile                   dev  swaplo blocks   free
/dev/zvol/dsk/rpool/swap  256,1      16 2097136 2097136
/dev/zvol/dsk/rpool/swap2 256,5      16 4194288 4194288

Do not swap to a file on a ZFS file system. A ZFS swap file configuration is not supported.

For information about adjusting the size of the swap and dump volumes, see Adjusting the Sizes of Your ZFS Swap Device and Dump Device.

Using a ZFS Volume as a Solaris iSCSI Target

You can easily create a ZFS volume as an iSCSI target by setting the shareiscsi property on the volume. For example:

# zfs create -V 2g tank/volumes/v2
# zfs set shareiscsi=on tank/volumes/v2
# iscsitadm list target
Target: tank/volumes/v2
    iSCSI Name: iqn.1986-03.com.sun:02:984fe301-c412-ccc1-cc80-cf9a72aa062a
    Connections: 0

After the iSCSI target is created, set up the iSCSI initiator. For more information about Solaris iSCSI targets and initiators, see Chapter 14, Configuring Oracle Solaris iSCSI Targets and Initiators (Tasks), in System Administration Guide: Devices and File Systems.


Note - Solaris iSCSI targets can also be created and managed with the iscsitadm command. If you set the shareiscsi property on a ZFS volume, do not use the iscsitadm command to also create the same target device. Otherwise, you create duplicate target information for the same device.


A ZFS volume as an iSCSI target is managed just like any other ZFS dataset. However, the rename, export, and import operations work a little differently for iSCSI targets.

All iSCSI target configuration information is stored within the dataset. Like an NFS shared file system, an iSCSI target that is imported on a different system is shared appropriately.