|Skip Navigation Links|
|Exit Print View|
|Oracle Solaris ZFS Administration Guide Oracle Solaris 10 8/11 Information Library|
The following sections provide detailed information about the following storage pool components:
The most basic element of a storage pool is physical storage. Physical storage can be any block device of at least 128 MB in size. Typically, this device is a hard drive that is visible to the system in the /dev/dsk directory.
A storage device can be a whole disk (c1t0d0) or an individual slice (c0t0d0s7). The recommended mode of operation is to use an entire disk, in which case the disk does not require special formatting. ZFS formats the disk using an EFI label to contain a single, large slice. When used in this way, the partition table that is displayed by the format command appears similar to the following:
Current partition table (original): Total disk sectors available: 286722878 + 16384 (reserved sectors) Part Tag Flag First Sector Size Last Sector 0 usr wm 34 136.72GB 286722911 1 unassigned wm 0 0 0 2 unassigned wm 0 0 0 3 unassigned wm 0 0 0 4 unassigned wm 0 0 0 5 unassigned wm 0 0 0 6 unassigned wm 0 0 0 8 reserved wm 286722912 8.00MB 286739295
To use a whole disk, the disk must be named by using the /dev/dsk/cNtNdN naming convention. Some third-party drivers use a different naming convention or place disks in a location other than the /dev/dsk directory. To use these disks, you must manually label the disk and provide a slice to ZFS.
ZFS applies an EFI label when you create a storage pool with whole disks. For more information about EFI labels, see EFI Disk Label in System Administration Guide: Devices and File Systems.
A disk that is intended for a ZFS root pool must be created with an SMI label, not an EFI label. You can relabel a disk with an SMI label by using the format -e command.
Disks can be specified by using either the full path, such as /dev/dsk/c1t0d0, or a shorthand name that consists of the device name within the /dev/dsk directory, such as c1t0d0. For example, the following are valid disk names:
Using whole physical disks is the easiest way to create ZFS storage pools. ZFS configurations become progressively more complex, from management, reliability, and performance perspectives, when you build pools from disk slices, LUNs in hardware RAID arrays, or volumes presented by software-based volume managers. The following considerations might help you determine how to configure ZFS with other hardware or software storage solutions:
If you construct a ZFS configuration on top of LUNs from hardware RAID arrays, you need to understand the relationship between ZFS redundancy features and the redundancy features offered by the array. Certain configurations might provide adequate redundancy and performance, but other configurations might not.
You can construct logical devices for ZFS using volumes presented by software-based volume managers, such as Solaris Volume Manager (SVM) or Veritas Volume Manager (VxVM). However, these configurations are not recommended. Although ZFS functions properly on such devices, less-than-optimal performance might be the result.
For additional information about storage pool recommendations, see Recommended Storage Pool Practices.
Disks are identified both by their path and by their device ID, if available. On systems where device ID information is available, this identification method allows devices to be reconfigured without updating ZFS. Because device ID generation and management can vary by system, export the pool first before moving devices, such as moving a disk from one controller to another controller. A system event, such as a firmware update or other hardware change, might change the device IDs in your ZFS storage pool, which can cause the devices to become unavailable.
Disks can be labeled with a traditional Solaris VTOC (SMI) label when you create a storage pool with a disk slice.
For a bootable ZFS root pool, the disks in the pool must contain slices and the disks must be labeled with an SMI label. The simplest configuration would be to put the entire disk capacity in slice 0 and use that slice for the root pool.
On a SPARC based system, a 72-GB disk has 68 GB of usable space located in slice 0 as shown in the following format output:
# format . . . Specify disk (enter its number): 4 selecting c1t1d0 partition> p Current partition table (original): Total disk cylinders available: 14087 + 2 (reserved cylinders) Part Tag Flag Cylinders Size Blocks 0 root wm 0 - 14086 68.35GB (14087/0/0) 143349312 1 unassigned wm 0 0 (0/0/0) 0 2 backup wm 0 - 14086 68.35GB (14087/0/0) 143349312 3 unassigned wm 0 0 (0/0/0) 0 4 unassigned wm 0 0 (0/0/0) 0 5 unassigned wm 0 0 (0/0/0) 0 6 unassigned wm 0 0 (0/0/0) 0 7 unassigned wm 0 0 (0/0/0) 0
On an x86 based system, a 72-GB disk has 68 GB of usable disk space located in slice 0, as shown in the following format output. A small amount of boot information is contained in slice 8. Slice 8 requires no administration and cannot be changed.
# format . . . selecting c1t0d0 partition> p Current partition table (original): Total disk cylinders available: 49779 + 2 (reserved cylinders) Part Tag Flag Cylinders Size Blocks 0 root wm 1 - 49778 68.36GB (49778/0/0) 143360640 1 unassigned wu 0 0 (0/0/0) 0 2 backup wm 0 - 49778 68.36GB (49779/0/0) 143363520 3 unassigned wu 0 0 (0/0/0) 0 4 unassigned wu 0 0 (0/0/0) 0 5 unassigned wu 0 0 (0/0/0) 0 6 unassigned wu 0 0 (0/0/0) 0 7 unassigned wu 0 0 (0/0/0) 0 8 boot wu 0 - 0 1.41MB (1/0/0) 2880 9 unassigned wu 0 0 (0/0/0) 0
An fdisk partition also exists on Solaris x86 systems. An fdisk partition is represented by a /dev/dsk/cN[tN]dNpN device name and acts as a container for the disk's available slices. Do not use a cN[tN]dNpN device for a ZFS storage pool component because this configuration is neither tested nor supported.
ZFS also allows you to use UFS files as virtual devices in your storage pool. This feature is aimed primarily at testing and enabling simple experimentation, not for production use. The reason is that any use of files relies on the underlying file system for consistency. If you create a ZFS pool backed by files on a UFS file system, then you are implicitly relying on UFS to guarantee correctness and synchronous semantics.
However, files can be quite useful when you are first trying out ZFS or experimenting with more complicated configurations when insufficient physical devices are present. All files must be specified as complete paths and must be at least 64 MB in size.