JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle Solaris Administration: IP Services     Oracle Solaris 11 Information Library
search filter icon
search icon

Document Information


Part I TCP/IP Administration

1.  Planning the Network Deployment

2.  Considerations When Using IPv6 Addresses

3.  Configuring an IPv4 Network

4.  Enabling IPv6 on the Network

5.  Administering a TCP/IP Network

6.  Configuring IP Tunnels

7.  Troubleshooting Network Problems

8.  IPv4 Reference

9.  IPv6 Reference


10.  About DHCP (Overview)

11.  Administering the ISC DHCP Service

12.  Configuring and Administering the DHCP Client

13.  DHCP Commands and Files (Reference)

Part III IP Security

14.  IP Security Architecture (Overview)

15.  Configuring IPsec (Tasks)

16.  IP Security Architecture (Reference)

17.  Internet Key Exchange (Overview)

18.  Configuring IKE (Tasks)

19.  Internet Key Exchange (Reference)

20.  IP Filter in Oracle Solaris (Overview)

21.  IP Filter (Tasks)

Part IV Networking Performance

22.  Integrated Load Balancer Overview

23.  Configuration of Integrated Load Balancer (Tasks)

24.  Virtual Router Redundancy Protocol (Overview)

25.  VRRP Configuration (Tasks)

26.  Implementing Congestion Control

Part V IP Quality of Service (IPQoS)

27.  Introducing IPQoS (Overview)

28.  Planning for an IPQoS-Enabled Network (Tasks)

29.  Creating the IPQoS Configuration File (Tasks)

30.  Starting and Maintaining IPQoS (Tasks)

Administering IPQoS (Task Map)

Applying an IPQoS Configuration

How to Apply a New Configuration to the IPQoS Kernel Modules

How to Ensure That the IPQoS Configuration Is Applied After Each Reboot

Enabling syslog Logging for IPQoS Messages

How to Enable Logging of IPQoS Messages During Booting

Troubleshooting with IPQoS Error Messages

31.  Using Flow Accounting and Statistics Gathering (Tasks)

32.  IPQoS in Detail (Reference)



Enabling syslog Logging for IPQoS Messages

To record IPQoS boot-time messages, you need to modify the /etc/syslog.conf file as shown in the next procedure.

How to Enable Logging of IPQoS Messages During Booting

  1. Open the /etc/syslog.conf file.
  2. Add the following text as the final entry in the file. /var/adm/messages

    Use tabs rather than spaces between the columns.

    The entry logs all boot-time messages that are generated by IPQoS into the /var/adm/messages file.

  3. Reboot the system to apply the messages.

Example 30-1 IPQoS Output From /var/adm/messages

When you view /var/adm/messages after system reboot, your output might contain IPQoS logging messages that are similar to the following.

May 14 10:44:33 ipqos-14 ipqosconf: [ID 815575]
 New configuration applied.
May 14 10:44:46 ipqos-14 ipqosconf: [ID 469457] 
Current configuration saved to init file.
May 14 10:44:55 ipqos-14 ipqosconf: [ID 435810]
Configuration flushed.

You might also see IPQoS error messages that are similar to the following in your IPQoS system's /var/adm/messages file.

May 14 10:56:47 ipqos-14 ipqosconf: [ID 123217 user.error]
 Missing/Invalid config file fmt_version.
May 14 10:58:19 ipqos-14 ipqosconf: [ID 671991 user.error] 
No ipgpc action defined.

For a description of these error messages, see Table 30-1.