Adding Systems to Be Installed From the Network With a DVD Image

After you create an install server and, if necessary, a boot server, you must set up each system that you want to install from the network. Use the procedure in this section for setting up install servers and clients. Also, see the following example procedures.

• If you are using DHCP to set installation parameters for a SPARC client, see Example 5-3.

• If your install server and client are on the same subnet, see Example 5-4.

• If your install server and your client are not on the same subnet and you are not using DHCP, see Example 5-5.

• If you are using DHCP to set installation parameters for x86 clients, see Example 5-6.

• If you want to use a specific serial port to display output during the installation of an x86 based system, see Example 5-7.

For more options to use with this command, see the add_install_client(1M) man page.

How to Add Systems to Be Installed From the Network With add_install_client (DVD)

After you create an install server, you must set up each x86 system that you want to install from the network.

Before You Begin

If you have a boot server, make sure you have shared the install server installation image and started the appropriate services. See “To Create a SPARC Install Server With SPARC or x86 DVD Media” Step 6.

Each system that you want to install needs to find the following items.

• An install server

• A boot server if one is required

• The sysidcfg file if you use a sysidcfg file to preconfigure system information

• A name server if you use a naming service to preconfigure system information

• The profile in the JumpStart directory on the profile server if you are using the JumpStart installation method

1. On the install server or boot server, become superuser or assume an equivalent role.

   ---

   Note - Roles contain authorizations and privileged commands. For more information about roles, see Configuring RBAC (Task Map) in System Administration Guide: Security Services.

   ---

2. If you use the NIS, NIS+, DNS, or LDAP naming service, verify that the following information about the system to be installed has been added to the naming service:

   • Host name

   • IP address

   • Ethernet address

   For more information on naming services, see System Administration Guide: Naming and Directory Services (DNS, NIS, and LDAP).

3. Add the client to the install server's /etc/ethers file.
   1. On the client, find the ethers address. The /etc/ethers map is taken from the local file.

      # ifconfig -a grep ether
      ether 8:0:20:b3:39:1d

   2. On the install server, add the address to the list in the /etc/ethers file.
4. Change to the Tools directory on the Oracle Solaris DVD image:

   # cd /install-dir-path/Solaris_10/Tools

   install-dir-path

   Specifies the path to the Tools directory

5. Set up the client system so it can be installed from the network.

   # ./add_install_client -d -s install-server:install-dir \
   -c JumpStart-server:JumpStart-dir  -p sysid-server:path \
   -t boot-image-path -b "boot-property=value" \
   -e Ethernet-address client-name platform-group

   -d

   Specifies that the client is to use DHCP to obtain the network install parameters. If you use only the -d option, the add_install_client command sets up the installation information for client systems of the same class, for example, all SPARC client machines. To set up the installation information for a specific client, use -d with the -e option.

   For x86 clients, use this option to boot the systems from the network by using PXE network boot. The output of this option lists the DHCP options you need to create on the DHCP server.

   For more information about class-specific installations by using DHCP, see Creating DHCP Options and Macros for Oracle Solaris Installation Parameters.

   -s install-server:install-dir

   Specifies the name and absolute path to the Oracle Solaris DVD image to the install server.

   -c JumpStart-server:JumpStart-dir

   Specifies a JumpStart directory for JumpStart installations. JumpStart-server is the host name of the server on which the JumpStart directory is located. JumpStart-dir is the absolute path to the JumpStart directory.

   -p sysid-server:path

   Specifies the path to the sysidcfg file for preconfiguring system information. sysid_server is either a valid host name or an IP address for the server that contains the file. path is the absolute path to the directory containing the sysidcfg file.

   -t boot-image-path

   Specifies the path to an alternate boot image if you want to use a boot image other than the one in the Tools directory on the current Oracle Solaris release net installation image, CD, or DVD.

   -b “boot-property=value”

   x86 based systems only: Enables you to set the value of a boot property variable that you want to use to boot the client from the network. The -b option must be used with the -e option.

   See the eeprom(1M) man page for descriptions of boot properties.

   -e Ethernet-address

   Specifies the Ethernet address of the client that you want to install. This option enables you to set up the installation information to use for a specific client, including a boot file for that client.

   The nbp. prefix is not used in boot file names. For example, if you specify -e 00:07:e9:04:4a:bf for an x86 based client, the command creates the boot file 010007E9044ABF.i86pc in the /tftpboot directory. However, the current Oracle Solaris release supports the use of legacy boot files with the nbp. prefix.

   For more information about client-specific installations by using DHCP, see Creating DHCP Options and Macros for Oracle Solaris Installation Parameters.

   client-name

   The name of the system to be installed from the network. This name is not the host name of the install server.

   platform-group

   The platform group of the system to be installed. For more information, see Platform Names and Groups in Oracle Solaris 10 1/13 Installation Guide: Planning for Installation and Upgrade.

Example 5-3 SPARC: Adding a SPARC Install Client on a SPARC Install Server When Using DHCP (DVD)

The following example illustrates how to add an install client when you are using DHCP to set installation parameters on the network. The install client is named basil, which is an Ultra 5 system. The file system /export/home/dvdsparc/Solaris_10/Tools contains the add_install_client command.

For more information about how to use DHCP to set installation parameters for network installations, see Preconfiguring System Configuration Information With the DHCP Service (Tasks).

mysparcinstallserver# cd /export/home/dvdsparc/Solaris_10/Tools
mysparcinstallserver# ./add_install_client -d basil sun4u

Example 5-4 Adding an Install Client That Is On the Same Subnet As Its Server (DVD)

The following example illustrates how to add an install client that is on the same subnet as the install server. The install client is named basil, which is an Ultra 5 system. The file system /export/home/dvdsparc/ contains the add_install_client command.

myinstallserver# cd /export/home/dvdsparc/Solaris_10/Tools
myinstallserver# ./add_install_client basil sun4u

Example 5-5 Adding an Install Client to a Boot Server (DVD)

The following example illustrates how to add an install client to a boot server. The install client is named rose, which is an Ultra 5 system. Run the command on the boot server. The -s option is used to specify an install server that is named rosemary, which contains Oracle Solaris Operating System for SPARC Platforms DVD image in /export/home/dvdsparc.

mybootserver# cd /export/home/dvdsparc/Solaris_10/Tools
mybootserver# ./add_install_client -s rosemary:/export/home/dvdsparc rose sun4u

Example 5-6 x86: Adding a Single x86 Install Client on an x86 Install Server When Using DHCP (DVD)

The following example illustrates how to add an x86 install client to an install server when you are using DHCP to set installation parameters on the network.

• The -d option specifies that clients are to use the DHCP protocol for configuration. If you plan to use PXE network boot, you must use the DHCP protocol.

• The -e option indicates that this installation will only occur on the client with the Ethernet address 00:07:e9:04:4a:bf.

• The -s option is used to specify that the clients are to be installed from the install server that is named rosemary.

This server contains Oracle Solaris Operating System for x86 Platforms DVD image in /export/home/dvdx86.

myx86installserver# cd /export/boot/dvdx86/Solaris_10/Tools
myx86installserver ./add_install_client -d -e 00:07:e9:04:4a:bf \ 
-s rosemary:/export/home/dvdx86 i86pc

The previous commands set up the client with the Ethernet address 00:07:e9:04:4a:bf as an installation client. The boot file 010007E9044ABF.i86pc is created on the installation server. In previous releases, this boot file was named nbp.010007E9044ABF.i86pc.

For more information about how to use DHCP to set installation parameters for network installations, see Preconfiguring System Configuration Information With the DHCP Service (Tasks).

Example 5-7 x86: Specifying a Serial Console to Use During a Network Installation (DVD)

The following example illustrates how to add an x86 install client to an install server and specify a serial console to use during the installation. This example sets up the install client in the following manner.

• The -d option indicates that the client is set up to use DHCP to set installation parameters.

• The -e option indicates that this installation will occur only on the client with the Ethernet address 00:07:e9:04:4a:bf.

• The -b option instructs the installation program to use the serial port ttya as an input and an output device.

Add the client:

myinstallserver# cd /export/boot/dvdx86/Solaris_10/Tools
myinstallserver# ./add_install_client -d -e "00:07:e9:04:4a:bf" \
-b "console=ttya" i86pc

For a complete description of the boot property variables and values you can use with the -b option, see the eeprom(1M) man page.

Next Steps

If you are using a DHCP server to install the x86 based client over the network, configure the DHCP server and create the options and macros that are listed in the output of the add_install_client -d command. For instructions about how to configure a DHCP server to support network installations, see Preconfiguring System Configuration Information With the DHCP Service (Tasks).

x86 based systems: If you are not using a DHCP server, you must boot the system from a local Oracle Solaris OS DVD or CD.

See Also

For additional information about the add_install_client command, see the install_scripts(1M) man page.