|
|
|
|
minus sign (-) |
Anything. The any keyword always succeeds. |
|
processor-typeValid values for processor-type are as follows:
|
A system's processor type. The uname -p
command reports the system's processor type. |
|
disk-name size-rangedisk-name – A disk
name in the form cxtydz, such as c0t3d0 or c0d0 or the
special word rootdisk. If rootdisk is used, the disk to be matched
is determined in the following order:
SPARC: The disk that contains the preinstalled boot image, which is a new SPARC based system with factory JumpStart installed
The c0t3d0s0 disk, if the disk exists
The first available disk that is searched in kernel probe order
size-range – The size of the disk, which must
be specified as a range of Mbytes (x-x).
Note - When calculating size-range, remember that a
MB equals 1,048,576 bytes. A disk might be advertised as a 535
MB disk, but the disk might contain only 510 million bytes of disk
space. The JumpStart program views the 535 MB disk as a 510 MB
disk because 535,000,000 / 1,048,576 = 510. A 535 MB disk does not
match a size-range equal to 530–550.
|
The name and size of a system's disk
in MB. For example: disksize c0t3d0 250-300 In the example, the JumpStart program attempts to match
a system disk that is named c0t3d0. The disk can hold between 250
and 300 MB of information. For example: disksize rootdisk 750-1000 In the example, the JumpStart program attempts
to match a disk in the following order:
A system disk that contains a preinstalled boot image
The c0t3d0s0 disk, if the disk exists
The first available disk that can hold between 750 MB and 1 GB of information
|
|
domain-name |
A system's domain
name, which controls how a naming service determines information. If you have a
system already installed, the domainname command reports the system's domain name. |
|
IP-address |
A system's IP address. |
|
host-name |
A system's host name. If you
have a system that is already installed, the uname -n command reports the system's
host name. |
|
slice versionslice – A disk slice
name in the form cwtxdysz, such as c0t3d0s5, or the special words any
or rootdisk. If any is used, the JumpStart program attempts to match all
of the system's disks in kernel probe order. If rootdisk is used,
the disk to be matched is determined in the following order:
SPARC: The disk that contains the preinstalled boot image, which is a new SPARC based system with factory JumpStart installed
The c0t3d0s0 disk, if the disk exists
The first available disk that is searched in kernel probe order
version – A
version name or the special words any or upgrade. If any is used, any
Oracle Solaris release is matched. If upgrade is used, any Oracle Solaris release
that is supported and can be upgraded is matched. If the JumpStart program finds
an Oracle Solaris release but is unable to determine the version, the version
that is returned is SystemV. |
A disk that has a root ( /) file
system that corresponds to a particular version of Oracle Solaris software. For example: installed c0t3d0s1 Solaris 10 In
the example, the JumpStart program attempts to match a system that has an
Oracle Solaris root (/) file system on c0t3d0s1. |
|
|
A system's platform group. If you have a system
that is already installed, the arch -k command or the uname -m command reports the
system's platform group. |
|
physical-memThe value must be a range
of MB, x-x, or a single MB value. |
A system's physical memory size
in MB. Example: memsize 64-128 The example tries to match a system with a physical
memory size between 64 and 128 MB. If you have a system that is
already installed, the output of the prtconf command, line 2, reports the
system's physical memory size. |
|
platform-name |
A system's platform name. See
the Oracle Solaris Sun Hardware Platform Guide at http://www.oracle.com/technetwork/indexes/documentation/index.html for a list of valid platform names. To find
the platform name of an installed system, use the uname -i command or
the output of the prtconf command, line 5.
Note - If platform-name contains spaces, you must replace
spaces with underscores (_). For example: SUNW, Sun_4_50
|
|
network-num |
A system's
network number, which the JumpStart program determines by performing a logical AND between
the system's IP address and the subnet mask. Example: network 192.168.2.0 The example tries
to match a system with a 192.168.2.8 IP address, if the subnet mask
is 255.255.255.0. |
|
Solaris_x |
A version of Oracle Solaris software
that is already installed on a system. For example: osname Solaris 10 In the example, the
JumpStart program attempts to match a system with the Oracle Solaris 10 8/11
OS already installed. |
|
probe-keyword |
A valid probe keyword or a valid custom probe
keyword. For example: probe disks The example returns the size of a system's disks in
MB and in kernel probe order, for example, c0t3d0s1, c0t4d0s0, on a SPARC based
system. The JumpStart program sets the SI_DISKLIST, SI_DISKSIZES, SI_NUMDISKS, and SI_TOTALDISK environment variables.
Note - The
probe keyword is unique in that the keyword does not attempt to match
an attribute and run a profile. The probe keyword returns a value. Consequently,
you cannot specify begin scripts, profiles, and finish scripts with the probe rule
keyword.
Probe keywords are described in Chapter 5, Creating Custom Rule and Probe Keywords (Tasks). |
|
size-rangeThe value must
be specified as a range of MB (x-x).
Note - When calculating size-range, remember that one
MB equals 1,048,576 bytes. A disk might be advertised as a 535
MB disk, but the disk might have only 510 million bytes of disk
space. The JumpStart program views the 535 MB disk as a 510 MB
disk because 535,000,000 / 1,048,576 = 510. A 535 MB disk does not
match a size-range equal to 530–550.
|
The total disk space on a system in
MB. The total disk space includes all the operational disks that are attached
to a system. For example: totaldisk 300-500 In the example, the JumpStart program tries to
match a system with a total disk space between 300 and 500 MB. |