This chapter briefly describes configuration files used by the WCC Integration feature. It also provides detailed information about wcc-integration.ini
, which contains user configurable parameters.
This chapter contains the following sections:
WCC connector configuration files consist of several INI
files located in the /Shared/clustersynch/ucm/ini
directory of the WebCenter Sites installation. The only file that may need editing is the wcc-integration.ini
file, which is used to optimize conditions for the WCC connector and to troubleshoot, as described in Section 54.2, "User Configurable Parameters."
Note:
The following configuration files must not be edited. They are used internally for data storage:wcc-matchers.ini
: Contains the rule statements that were created via the rules wizard in the WebCenter Sites Connector Admin tab. Each rule is listed by name and identified as either enabled or disabled. Also included are a description of the rule and its statement logic. This file is paired with the wcc-mappers.ini
file.
wcc-mappers.ini
: Contains the rule details defined in the rules wizard. This file is paired with the wcc-matchers.ini
file.
wcc-token.ini
: Contains a token received from WebCenter Content indicating the last time the server synchronized with WebCenter Sites.
The wcc-integration.ini
configuration file contains several system parameters that are user configurable. These parameters are not configurable in the WebCenter Sites Admin interface.
The wcc-integration.ini
configuration file is located in the /Shared/clustersynch/ucm/ini
directory of the WebCenter Sites installation, and it uses the Java property file format, as shown in the following example:
#wcc-integration.ini wcc.batch.size=50 wcc.batch.autorepeat=true wcc.download.dir=C\:\\Oracle\\WebCenter\\Sites\\tomcat\\temp wcc.download.autoclean=true wcc.keyfield=name wcc.rule.case-sensitive=true
Parameters listed in the example above are user configurable and defined as follows:
wcc.batch.size=[
50
]
When a lot of content needs to be processed, processing is done in batches. This parameter specifies the maximum size of the batch.
When the wcc-integration.ini
configuration file is created, the default batch size is set to 50
. This value can be changed, but the parameter cannot be left blank and must contain a valid value.
wcc.batch.autorepeat=[
true
| false]
If the connector runs and receives a response that the total number of items exceeds the number defined in the wcc.batch.size
parameter, then the connector can be set to either automatically run again once the batch is processed (true
), or the connector can wait for the next manual or next timed run (false
).
When the wcc-integration.ini
configuration file is created, this parameter is set to a default value of true
. The value can be changed, but the parameter cannot be left blank and must contain a valid value. Valid values are true
or false
.
wcc.download.dir=[temporary_zip_file_location]
This parameter defines the temporary download location of the ZIP files that are transferred from WebCenter Content.
wcc.download.autoclean=[
true
| false]
This parameter defines whether to delete the ZIP file when processing is complete. This is a debugging parameter that will either force the temporary files to be cleaned up (true
), or leave files on disk for analysis (false
).
When the wcc-integration.ini
configuration file is created, this parameter is set to a default value of true
. The value can be changed, but the parameter cannot be left blank and must contain a valid value. Valid values are true
or false
.
wcc.keyfield=[name]
This parameter specifies the name of the asset type attribute that will receive the value of the dDocName
metadata field in WebCenter Content. By default, the value of wcc.keyfield is name
, because name is a default attribute available in every asset type. It is unlikely that this value would need to be edited.
This value may be changed once, on a new system, before rules are created, and before content synchronization begins. Once synchronization starts, this value should not be edited. Otherwise, assets may be duplicated. An example situation where the default value might be changed is when the name
field is already in use. For more information about dDocName
, see Section 50.4.1.1, "Content Identifier Attribute."
wcc.rule.case-sensitive=[
true
| false]
This parameter is used to compare string metadata values specified in connector rules with the actual metadata values of content items. If the parameter is set to true
, case-sensitivity is enabled.
When the wcc-integration.ini
configuration file is created, this parameter is set to a default value of true
. Valid values are true
or false
.