|Oracle® Real User Experience Insight Installation Guide
12c Release 2 (184.108.40.206) for Linux x86-64
Part Number E37265-05
|PDF · Mobi · ePub|
The information in this appendix is based on the Oracle Database 11g for Linux x86-64 Quick Installation Guide. It is recommended that you download and review it. It is available from the Oracle Database Documentation Library at the following location:
Download Oracle Database 11g Release 2 (220.127.116.11.0) Standard Edition, Standard Edition One, and Enterprise Edition from the Oracle database home page at the following location:
Assuming you have a working Yum repository, you can install the required operating system dependencies for the database software with the following command:
yum install gcc gcc-c++ compat-libstdc++-33 glibc-devel libstdc++-devel \ elfutils-libelf-devel glibc-devel libaio-devel sysstat perl-URI \ bitstream-vera-fonts xorg-x11-xinit unixODBC unixODBC-devel xorg-x11-xinit
/usr/sbin/groupadd dba /usr/sbin/groupadd oinstall
oracle user, and specify
oinstall as the primary group and
dba as the secondary group, with the following command:
/usr/sbin/useradd -g oinstall -G dba oracle
oracle user password with the following command:
/etc/sysctl.conf file to satisfy the Oracle installer's requirements by adding the following lines:
kernel.sem = 250 32000 100 128 net.ipv4.ip_local_port_range = 9000 65500 net.core.rmem_default = 4194304 net.core.rmem_max = 4194304 net.core.wmem_default = 262144 net.core.wmem_max = 1048576 fs.aio-max-nr = 1048576 fs.file-max = 681574
Make these changes effective immediately with the following command:
To improve the performance of the software, you must increase the shell limits for the
oracle user. Add the following lines to the
oracle soft nproc 2047 oracle hard nproc 16384 oracle soft nofile 1024 oracle hard nofile 65536
If not already present, add the following lines to the
session required /lib64/security/pam_limits.so session required pam_limits.so
Depending on the
oracle user's default shell, you need to make changes to it. For the Bourne, Bash, or Korn shell, add the following lines to the bottom of the
if [ $USER = "oracle" ]; then if [ $SHELL = "/bin/ksh" ]; then ulimit -p 16384 ulimit -n 65536 else ulimit -u 16384 -n 65536 fi fi
For information about other shells, you should refer to the Oracle Database 11g Release 1 for Linux x86-64 Quick Installation Guide available at the following location:
Throughout this guide it is assumed that the directory
/u01/app is the root of the Oracle installation. This is specified in the
ORACLE_BASE environment variable.
Enter the following command to display information about all mounted file systems:
This command displays information about all the file systems mounted on the system, including:
The physical device name.
The total amount, used amount, and available amount of disk space.
The mount point directory for that file system.
Create the necessary subdirectories in the mount point directory that you identified and set the appropriate owner, group, and permissions for them using commands similar to the following:
mkdir -p /u01/app chown -R oracle:oinstall /u01 chmod -R 775 /u01/app
Logon to the system as the
Add or edit the
umask setting in the
~/.bash_profile file to the following:
Make the setting active for the current shell by issuing the following command:
ORACLE_BASE environment variable to define the location of the root of the Oracle directory tree:
Unzip the Oracle database installation zip file. This creates the directory
database. Then, run the graphical installer (note this will not run under user
root). Ensure that your X Window environment is properly set up. In addition, when logging on remotely with SSH, ensure X forwarding is enabled. Use the following commands:
cd <location of the zip file> unzip linux_11gR2_database.zip ./database/runInstaller
Use the installation wizard, and specify the values shown in Figure A-1. When ready, click Next.
Specify the values shown in Figure A-2. When ready, click Next.
Important:Any warnings or errors reported during database installation (especially any missing prerequisites) must be resolved before proceeding. See Installing the RUEI Prerequisites and Appendix G, "Troubleshooting" for information about required components.
If all dependencies are met, you can click Next.
When installation is almost complete, you are prompted to run two scripts,
root. This is shown in Figure A-3.
Run the two scripts indicated in Figure A-3. They should be run in a terminal window as
root. You will receive output similar to the following:
/u01/app/oraInventory/orainstRoot.sh Changing permissions of /u01/app/oraInventory. Adding read,write permissions for group. Removing read,write,execute permissions for world. Changing groupname of /u01/app/oraInventory to oinstall. The execution of the script is complete.
The second script generates the following output:
/u01/app/oracle/product/11.2.0/dbhome_1 /root.sh Running Oracle 11g root.sh script... The following environment variables are set as: ORACLE_OWNER= oracle ORACLE_HOME= /u01/app/oracle/product/11.2.0/dbhome_1 Enter the full pathname of the local bin directory: [/usr/local/bin]: Copying dbhome to /usr/local/bin ... Copying oraenv to /usr/local/bin ... Copying coraenv to /usr/local/bin ... Creating /etc/oratab file... Entries will be added to the /etc/oratab file as needed by Database Configuration Assistant when a database is created Finished running generic part of root.sh script. Now product-specific root actions will be performed. Finished product-specific root actions.
On completion of each script, return the dialog shown in Figure A-3, and click OK. In the main installer screen, verify that the message "The installation of Oracle database 11g was successful" appears. Click Exit, and confirm by clicking Yes.
Logon as the
/etc/init.d/oracledb script file to start and stop the Oracle database. An example of this initialization script is available in the RUEI installation zip file (
/root/RUEI/extra/oracledb) explained in Chapter 2, "Installing the RUEI Software". Note that you will need to modify the settings for the
ORACLE_HOME environment variables shown above if you selected a different installation directory for the Oracle database.
Make the script file executable and use it to start the Oracle database with the following commands:
chmod +x /etc/init.d/oracledb /sbin/chkconfig --add oracledb /sbin/service oracledb start
The Oracle database is now installed, and the database listener should be up and running.