Go to main content
Oracle® ZFS Storage ZS5-4 Getting Started Guide

Exit Print View

Updated: December 2016
 
 

Oracle® ZFS Storage ZS5-4 Getting Started Guide

Contents

image:The image shows the shipping items.
1 Oracle ZFS Storage ZS5-4 controller
2 Cable management arm
3 Slide rail kit
4 Four 6-meter Ethernet cables
5 Three 2.5-meter Ethernet cables
6 Eight 3-meter SAS cables (up to sixteen 3-meter or 6-meter cables per customer request)
7 Two power cords

Front Panel Components

image:The table describes the callouts.
1 LEDs (left to right)
  • Locator

  • Service action required

  • Power/OK

2 Power button
3 Alert indicators (left to right)
  • Service Processor (SP) OK/Fault

  • Fan/ CPU/ Memory service action required

  • Power Supply (PS) service action required

  • Over-temperature warning

4 Permanent HDD filler panels
5 System disk 1
6 System disk 0
7 DVD filler panel
8 DB-15 VGA port
9 Two USB 2.0 ports
10 RFID tag

Back Panel Components

image:This image shows the rear panel components.
1 Power Supply Unit (PSU) 0
2 PSU 1
3 DB-15 VGA port
4 SER MGT port
5 Service Processor (SP) NET MGT port
6 First PCle (slot 11)
7 Fifth PCIe (slot 10)
8 Third 4x4 SAS HBA or seventh PCIe (slot 9)
9 Second PCIe (slot 8)
10 4X4 SAS HBA (slot 7)
11 Two USB 2.0 ports
12 Network (NET) 10 Gb Ethernet ports, NET 0 - NET 3
13 4X4 SAS HBA (slot 6)
14 Third PCIe (slot 5)
15 Cluster interface card (slot 4)
16 Fourth 4X4 SAS HBA or sixth PCIe (slot 3)
17 Internal SAS-3 HBA (slot 2)
18 Fourth PCIe (slot 1)
19 System status LEDs (left to right)
  • Power/OK (green)

  • Attention (amber)

  • Locate (white)

20 PSU 1 AC inlet
21 PSU 0 AC inlet

Install the Hardware

For detailed information, see the Oracle ZFS Storage Appliance Installation Guide available from http://docs.oracle.com/en/storage.

image:The graphic shows how to install the hardware.

Connect System Cables

For detailed information, see the Oracle ZFS Storage Appliance Installation Guide available from http://docs.oracle.com/en/storage. If you have clustered controllers, connect the cables to both controllers. Do not connect power cables to the controllers or disk shelves until instructed to do so in "Power On and Configure the System."

image:The graphic shows how to connect system cables.

Connect Clustered Controllers

If you have clustered controllers, connect the two controllers together. For detailed information, see the Oracle ZFS Storage Appliance Cabling Guide available from http://docs.oracle.com/en/storage.

image:The image shows how to connect clustered                                         controllers.

Connect Disk Shelves

The following illustration shows clustered ZS5-4 controllers, each with two HBAs connected to four Oracle Storage Drive Enclosure DE3-24 disk shelves in two chains. For additional configuration options, see the Oracle ZFS Storage Appliance Cabling Guide available from http://docs.oracle.com/en/storage. Do not connect power cables to the disk shelves or controllers until instructed to do so in "Power On and Configure the System."

image:The image shows how to connect disk shelves to                                         controllers.

Power On and Configure the System

Required information: A) Network host name and port of your serial connection, or B) Network management port DHCP-assigned address. Connect disk shelf power cables, power on disk shelves, connect controller power cables, power on controllers, and configure the system as described in the Oracle ZFS Storage Appliance Installation Guide available from http://docs.oracle.com/en/storage.

image:The graphic shows how to power on system and configure                                         primary network interface.

Perform Initial Configuration

For detailed information, see the Oracle ZFS Storage Appliance Installation Guide available from http://docs.oracle.com/en/storage, including properly configuring the management interfaces and updating the controller software.

image:The graphic shows how to perform initial                                         configuration.