WTCLocalTuxDomMBean

Overview

This interface provides access to the WTC local Tuxedo Domain configuration attributes. The methods defined herein are applicable for WTC configuration at the WLS domain level.

Fully Qualified Interface Name

If you use the getMBeanInfo operation in MBeanTypeServiceMBean, supply the following value as this MBean's fully qualified interface name:
weblogic.management.configuration.WTCLocalTuxDomMBean

Since 7.0.0.0

Factory Methods

• Factory methods in WTCServerMBean

Additional Access Points

In addition to accessing this MBean by invoking a factory method, you can also access this MBean from the following MBean attributes:

Attributes

This section describes the following attributes:

AccessPoint

The unique name used to identify this local Tuxedo access point. This name should be unique for all local and remote Tuxedo access points defined within a WTC Service. This allows you to define unique configurations having the same Access Point ID.

AccessPointId

The connection principal name used to identify this local Tuxedo access point when attempting to establish a session connection with remote Tuxedo access points.

Note: The AccessPointId must match the corresponding DOMAINID in the *DM_REMOTE_DOMAINS section of your Tuxedo DMCONFIG file.

BlockTime

The maximum number of seconds this local Tuxedo access point allows for a blocking call.

Range of Values: Between 0 and a positive 32 bit integer.

CmpLimit

The compression threshold this local Tuxedo access point uses when sending data to a remote Tuxedo access point. Application buffers larger than this size are compressed.

Range of Values: Between 0 and a positive 32-bit integer.

ConnectionPolicy

The conditions under which this local Tuxedo access point establishes a session connection with a remote Tuxedo access point.

The connection policies are:

• ON_DEMAND

  : A connection is attempted only when requested by either a client request to a remote service or an administrative connect command.

• ON_STARTUP

  : A domain gateway attempts to establish a connection with its remote Tuxedo access points at gateway server initialization time. Remote services (services advertised in JNDI by the domain gateway for this local access point) are advertised only if a connection is successfully established to that remote Tuxedo access point. If there is no active connection to a remote Tuxedo access point, then the remote services are suspended. By default, this connection policy retries failed connections every 60 seconds. Use the MaxRetry and RetryInterval values to specify application specific values.

• INCOMING_ONLY

  : A domain gateway does not attempt an initial connection to remote Tuxedo access points at startup and remote services are initially suspended. The domain gateway is available for incoming connections from remote Tuxedo access points and remote services are advertised when the domain gateway for this local Tuxedo access point receives an incoming connection. Connection retry processing is not allowed.

ConnPrincipalName

The principal name used to verify the identity of this domain when establishing a connection to another domain.

Note: This parameter only applies to domains of type TDOMAIN that are running BEA Tuxedo 7.1 or later software. If not specified, the connection principal name defaults to the AccessPointID for this domain.ConnPrincipalName.

Note: ConnPrincipalName is not supported in this release.

Interoperate

Specifies whether this local Tuxedo access point interoperates with remote Tuxedo access points that are based upon Tuxedo release 6.5. If this value is set to Yes, the local Tuxedo access point interoperates with a Tuxedo 6.5 domain.

MaxEncryptBits

The maximum encryption key length (in bits) this local Tuxedo access point uses when establishing a session connection. A value of 0 indicates no encryption is used.

Value Restrictions:

• The MaxEncryptBits value must be greater than or equal to the MinEncrypBits value.

• A MaxEncryptBits of 40 can be used only with domains running Tuxedo 7.1 or higher.

MaxRetries

The maximum number of times that this local Tuxedo access point tries to establish a session connection to remote Tuxedo access points. Use this value only when Connection Policy is set to ON_STARTUP.

Range of Values: Between 0 and a positive 64 bit integer.

Note: Use the minimum value to disable the retry mechanism. Use the maximum value to try until a connection is established.

MinEncryptBits

The minimum encryption key length (in bits) this local Tuxedo access point uses when establishing a session connection. A value of 0 indicates no encryption is used.

Value Restrictions:

• The MinEncrypBits value must be less than or equal to the MaxEncrypBits value.

• A MinEncrypBits value of 40 can be used only with domains running Tuxedo 7.1 or higher.

Name

The user-specified name of this MBean instance.

This name is included as one of the key properties in the MBean's javax.management.ObjectName:
Name=user-specified-name

Notes

Optional information that you can include to describe this configuration.

WebLogic Sever saves this note in the domain's configuration file (config.xml) as XML PCDATA. All left angle brackets (<) are converted to the XML entity <. Carriage returns/line feeds are preserved.

Note:

If you create or edit a note from the Administration Console, the Administration Console does not preserve carriage returns/line feeds.

NWAddr

The network address and port number of this local Tuxedo access point. Specify the TCP/IP address in the format: //hostname:port_number or //#.#.#.#:port_number.

Note: If the hostname is used, the access point finds an address for hostname using the local name resolution facilities (usually DNS). If dotted decimal format is used, each # should be a number from 0 to 255. This dotted decimal number represents the IP address of the local machine. The port_number is the TCP port number at which the access point listens for incoming requests.

Parent

Return the immediate parent for this MBean

RetryInterval

The number of seconds that this local Tuxedo access point waits between automatic connection attempts to remote Tuxedo access points. Use this value only when Connection Policy is set to ON_STARTUP.

Range of Values: Between 0 and a positive 32-bit integer.

Security

The type of application security enforced.

The types of security are:

• NONE

  : No security is used.

• APP_PW

  : Password security is enforced when a connection is established from a remote domain. The application password is defined in the WTCResourcesMBean.

• DM_PW

  : Domain password security is enforced when a connection is established from a remote domain. The domain password is defined in the WTCPasswordsMBean.

Type

Returns the type of the MBean.

Operations

This section describes the following operations:

freezeCurrentValue

If the specified attribute has not been set explicitly, and if the attribute has a default value, this operation forces the MBean to persist the default value.

Unless you use this operation, the default value is not saved and is subject to change if you update to a newer release of WebLogic Server. Invoking this operation isolates this MBean from the effects of such changes.

Note:

To insure that you are freezing the default value, invoke the restoreDefaultValue operation before you invoke this.

This operation has no effect if you invoke it on an attribute that does not provide a default value or on an attribute for which some other value has been set.

Deprecated. 9.0.0.0

Exceptions

• javax.management.AttributeNotFoundException
• javax.management.MBeanException

isSet

Returns true if the specified attribute has been set explicitly in this MBean instance.

restoreDefaultValue

If the specified attribute has a default value, this operation removes any value that has been set explicitly and causes the attribute to use the default value.

Default values are subject to change if you update to a newer release of WebLogic Server. To prevent the value from changing if you update to a newer release, invoke the freezeCurrentValue operation.

This operation has no effect if you invoke it on an attribute that does not provide a default value or on an attribute that is already using the default.

Deprecated. 9.0.0.0

Exceptions

• javax.management.AttributeNotFoundException

unSet

Restore the given property to its default value.