7 Parameters for Web Server Plug-Ins

The following sections describe the parameters that you use to configure the Apache and Microsoft IIS Web server plug-ins:

• "Entering Parameters in Web Server Plug-In Configuration Files"

• "General Parameters for Web Service Plug-Ins"

• "SSL Parameters for Web Server Plug-Ins"

Entering Parameters in Web Server Plug-In Configuration Files

You enter the parameters for each Web server plug-in in special configuration files. Each Web server has a different name for this configuration file and different rules for formatting the file. For details, see the following sections on each plug-in:

• Chapter 3, "Installing and Configuring the Apache HTTP Server Plug-In"

• Chapter 4, "Installing and Configuring the Microsoft IIS Plug-In"

General Parameters for Web Service Plug-Ins

The general parameters for Web Service plug-ins are shown in Table 7-1. Parameters are case sensitive.

Table 7-1 General Parameters for Web Service Plug-Ins

Parameter Name	Default	Description	Applicable to
WebLogicHost (Required when proxying to a single WebLogic Server.)	none	WebLogic Server host (or virtual host name as defined in WebLogic Server) to which HTTP requests should be forwarded. If you are using a WebLogic cluster, use the WebLogicCluster parameter instead of WebLogicHost.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
WebLogicPort (Required when proxying to a single WebLogic Server.)	none	Port at which the WebLogic Server host is listening for connection requests from the plug-in (or from other servers). (If you are using SSL between the plug-in and WebLogic Server, set this parameter to the SSL listen port (see Configuring SSL) and set the SecureProxy parameter to ON). If you are using a WebLogic Cluster, use the WebLogicCluster parameter instead of WebLogicPort.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
WebLogicCluster (Required when proxying to a cluster of WebLogic Servers.)	none	List of WebLogic Servers that can be used for load balancing. The server or cluster list is a list of host:port entries. If a mixed set of clusters and single servers is specified, the dynamic list returned for this parameter will return only the clustered servers. The method of specifying the parameter, and the required format vary by plug-in. See the examples in: Chapter 4, "Installing and Configuring the Microsoft IIS Plug-In" Chapter 3, "Installing and Configuring the Apache HTTP Server Plug-In" If you are using SSL between the plug-in and WebLogic Server, set the port number to the SSL listen port (see Configuring SSL) and set the SecureProxy parameter to ON. The plug-in does a simple round-robin between all available servers. The server list specified in this property is a starting point for the dynamic server list that the server and plug-in maintain. WebLogic Server and the plug-in work together to update the server list automatically with new, failed, and recovered cluster members. You can disable the use of the dynamic cluster list by setting the DynamicServerList parameter to OFF. The plug-in directs HTTP requests containing a cookie, URL-encoded session, or a session stored in the POST data to the server in the cluster that originally created the cookie.	ISAPI, Apache and NSAPI plug-in,and HttpClusterServlet
PathTrim	null	As per the RFC specification, generic syntax for URL is: [PROTOCOL]://[HOSTNAME]:{PORT}/{PATH}/{FILENAME};{PATH_PARAMS}/{QUERY_STRING}... PathTrim specifies the string trimmed by the plug-in from the {PATH}/{FILENAME} portion of the original URL, before the request is forwarded to WebLogic Server. For example, if the URL http://myWeb.server.com/weblogic/foo is passed to the plug-in for parsing and if PathTrim has been set to strip off /weblogic before handing the URL to WebLogic Server, the URL forwarded to WebLogic Server is: http://myWeb.server.com:7001/foo Note that if you are newly converting an existing third-party server to proxy requests to WebLogic Server using the plug-in, you will need to change application paths to /foo to include weblogic/foo. You can use PathTrim and PathPrepend in combination to change this path.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
PathPrepend	null	As per the RFC specification, generic syntax for URL is: [PROTOCOL]://[HOSTNAME]:{PORT}/{PATH}/{FILENAME};{PATH_PARAMS}/{QUERY_STRING}... PathPrepend specifies the path that the plug-in prepends to the {PATH} portion of the original URL, after PathTrim is trimmed and before the request is forwarded to WebLogic Server. Note that if you need to append File Name, use DefaultFileName plug-in parameter instead of PathPrepend.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
ConnectTimeoutSecs	10	Maximum time in seconds that the plug-in should attempt to connect to the WebLogic Server host. Make the value greater than ConnectRetrySecs. If ConnectTimeoutSecs expires without a successful connection, even after the appropriate retries (see ConnectRetrySecs), an HTTP 503/Service Unavailable response is sent to the client. You can customize the error response by using the ErrorPage parameter.	NSAPI, ISAPI, and Apache plug-in, and HttpClusterServlet
ConnectRetrySecs	2	Interval in seconds that the plug-in should sleep between attempts to connect to the WebLogic Server host (or all of the servers in a cluster). Make this number less than the ConnectTimeoutSecs. The number of times the plug-in tries to connect before returning an HTTP 503/Service Unavailable response to the client is calculated by dividing ConnectTimeoutSecs by ConnectRetrySecs. To specify no retries, set ConnectRetrySecs equal to ConnectTimeoutSecs. However, the plug-in attempts to connect at least twice. You can customize the error response by using the ErrorPage parameter.	NSAPI, ISAPI, and Apache plug-in, and HttpClusterServlet
Debug	OFF	Sets the type of logging performed for debugging operations. The debugging information is written to the /tmp/wlproxy.log file on UNIX systems and c:\TEMP\wlproxy.log on Windows NT/2000 systems. Override this location and filename by setting the WLLogFile parameter to a different directory and file. (See the WLTempDir parameter for an additional way to change this location.) Ensure that the tmp or TEMP directory has write permission assigned to the user who is logged in to the server. Set any of the following logging options (HFC,HTW,HFW, and HTC options may be set in combination by entering them separated by commas, for example “HFC,HTW”): ON The plug-in logs informational and error messages. OFF No debugging information is logged. HFC The plug-in logs headers from the client, informational, and error messages. HTW The plug-in logs headers sent to WebLogic Server, and informational and error messages. HFW The plug-in logs headers sent from WebLogic Server, and informational and error messages. HTC The plug-in logs headers sent to the client, informational messages, and error messages. ERR Prints only the Error messages in the plug-in. ALL The plug-in logs headers sent to and from the client, headers sent to and from WebLogic Server, information messages, and error messages.	NSAPI, ISAPI, and Apache plug-in, HttpClusterServlet, and HttpProxyServlet
WLLogFile	See the Debug parameter	Specifies path and file name for the log file that is generated when the Debug parameter is set to ON. You must create this directory before setting this parameter.	NSAPI, ISAPI, and Apache plug-in, HttpClusterServlet, and HttpProxyServlet
WLDNSRefreshInterval	0 (Lookup once, during startup)	Only applies to NSAPI and Apache. If defined in the proxy configuration, specifies number of seconds interval at which WebLogic Server refreshes DNS name to IP mapping for a server. This can be used in the event that a WebLogic Server instance is migrated to a different IP address, but the DNS name for that server's IP remains the same. In this case, at the specified refresh interval the DNS<->IP mapping will be updated.	NSAPI and Apache plug-in
WLTempDir	See the Debug parameter	Specifies the directory where a wlproxy.log will be created. If the location fails, the Plug-In resorts to creating the log file under C:/temp in Windows and /tmp in all Unix platforms. Also specifies the location of the _wl_proxy directory for POST data files. When both WLTempDir and WLLogFile are set, WLLogFile will override as to the location of wlproxy.log. WLTempDir will still determine the location of _wl_proxy directory.	NSAPI, ISAPI, and Apache plug-in
DebugConfigInfo	OFF	Enables the special query parameter “__WebLogicBridgeConfig”. Use it to get details about configuration parameters from the plug-in. For example, if you enable “__WebLogicBridgeConfig” by setting DebugConfigInfo and then send a request that includes the query string ?__WebLogicBridgeConfig, then the plug-in gathers the configuration information and run-time statistics and returns the information to the browser. The plug-in does not connect to WebLogic Server in this case. This parameter is strictly for debugging and the format of the output message can change with releases. For security purposes, keep this parameter turned OFF in production systems.	NSAPI, ISAPI, and Apache plug-in, HttpClusterServlet, and HttpProxyServlet
StatPath (Not available for the Microsoft Internet Information Server Plug-In)	false	If set to true, the plug-in checks the existence and permissions of the translated path (“Proxy-Path-Translated”) of the request before forwarding the request to WebLogic Server. If the file does not exist, an HTTP 404 File Not Found response is returned to the client. If the file exists but is not world-readable, an HTTP 403/Forbidden response is returned to the client. In either case, the default mechanism for the Web server to handle these responses fulfills the body of the response. This option is useful if both the WebLogic Server Web Application and the Web Server have the same document root. You can customize the error response by using the ErrorPage parameter.	NSAPI and Apache plug-in
ErrorPage	none	You can create your own error page that is displayed when your Web server is unable to forward requests to WebLogic Server.	ISAPI, Apache, and NSAPI plug-in
WLSocketTimeoutSecs	2 (must be greater than 0)	Set the timeout for the socket while connecting, in seconds.
WLIOTimeoutSecs (new name for HungServerRecoverSecs)	300	Defines the amount of time the plug-in waits for a response to a request from WebLogic Server. The plug-in waits for WLIOTimeoutSecs for the server to respond and then declares that server dead, and fails over to the next server. The value should be set to a very large value. If the value is less than the time the servlets take to process, then you may see unexpected results. Minimum value: 10 Maximum value: Unlimited	NSAPI, ISAPI, and Apache plug-in
Idempotent	ON	When set to ON and if the servers do not respond within WLIOTimeoutSecs (new name for HungServerRecoverSecs), the plug-ins fail over. If set to “OFF” the plug-ins do not fail over. If you are using the Apache HTTP Server you can set this parameter differently for different URLs or MIME types.	ISAPI, Apache and NSAPI plug-in, and HttpClusterServlet
WLCookieName CookieName parameter is deprecated	JSESSIONID	If you change the name of the WebLogic Server session cookie in the WebLogic Server Web application, you need to change the WLCookieName parameter in the plug-in to the same value. The name of the WebLogic session cookie is set in the WebLogic-specific deployment descriptor, in the <session-descriptor> element.	NSAPI, ISAPI, and Apache plug-in, HttpClusterServlet, and HttpProxyServlet
DefaultFileName	none	If the URI is “/” then the plug-in performs the following steps: Trims the path specified with the PathTrim parameter. Appends the value of DefaultFileName. Prepends the value specified with PathPrepend. This procedure prevents redirects from WebLogic Server. Set the DefaultFileName to the default welcome page of the Web Application in WebLogic Server to which requests are being proxied. For example, If the DefaultFileName is set to welcome.html, an HTTP request like “http://somehost/weblogic” becomes “http://somehost/weblogic/welcome.html”. For this parameter to function, the same file must be specified as a welcome file in all the Web Applications to which requests are directed. For more information, see Configuring Welcome Pages. Note for Apache users: If you are using Stronghold or Raven versions, define this parameter inside of a Location block, and not in an IfModule block.	NSAPI, ISAPI, and Apache plug-in, HttpClusterServlet, and HttpProxyServlet
MaxPostSize	-1	Maximum allowable size of POST data, in bytes. If the content-length exceeds MaxPostSize, the plug-in returns an error message. If set to -1, the size of POST data is not checked. This is useful for preventing denial-of-service attacks that attempt to overload the server with POST data.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
MatchExpression (Apache HTTP Server only)	none	When proxying by MIME type, set the filename pattern inside of an IfModule block using the MatchExpression parameter. Example when proxying by MIME type: <IfModule weblogic_module> MatchExpression *.jsp WebLogicHost=myHost|paramName=value </IfModule> Example when proxying by path: <IfModule weblogic_module> MatchExpression /weblogic WebLogicHost=myHost|paramName=value </IfModule> It is possible to define a new parameter for MatchExpression using the following syntax: MatchExpression *.jsp PathPrepend=/test PathTrim=/foo	Apache plug-in
FileCaching	ON	When set to ON, and the size of the POST data in a request is greater than 2048 bytes, the POST data is first read into a temporary file on disk and then forwarded to the WebLogic Server in chunks of 8192 bytes. This preserves the POST data during failover, allowing all necessary data to be repeated to the secondary if the primary goes down. Note that when FileCaching is ON, any client that tracks the progress of the POST will see that the transfer has completed even though the data is still being transferred between the WebServer and WebLogic. So, if you want the progress bar displayed by a browser during the upload to reflect when the data is actually available on the WebLogic Server, you might not want to have FileCaching ON. When set to OFF and the size of the POST data in a request is greater than 2048 bytes, the reading of the POST data is postponed until a WebLogic Server cluster member is identified to serve the request. Then the Plugin reads and immediately sends the POST data to the WebLogic Server in chunks of 8192 bytes. Note that turning FileCaching OFF limits failover. If the WebLogic Server primary server goes down while processing the request, the POST data already sent to the primary cannot be repeated to the secondary. Finally, regardless of how FileCaching is set, if the size of the POST data is 2048 bytes or less the plugin will read the data into memory and use it if needed during failover to repeat to the secondary.	ISAPI, Apache and NSAPI plug-in, and HttpClusterServlet
FilterPriorityLevel	2	The values for this parameter are 0 (low), 1 (medium), and 2 (high). The default value is 2. This priority should be put in iisforward.ini file. This property is used to set the priority level for the iisforward.dll filter in IIS. Priority level is used by IIS to decide which filter will be invoked first, in case multiple filters match the incoming request.	ISAPI plug-in
WLExcludePathOrMimeType	none	This parameter allows you make exclude certain requests from proxying. This parameter can be defined locally at the Location tag level as well as globally. When the property is defined locally, it does not override the global property but defines a union of the two parameters.	NSAPI, ISAPI, and Apache plug-in
WlForwardPath	null	If WlForwardPath is set to "/" all requests are proxied. To forward any requests starting with a particular string, set WlForwardPath to the string. For example, setting WlForwardPath to /weblogic forwards all requests starting with /weblogic to Weblogic Server. This parameter is required if you are proxying by path. You can set multiple strings by separating the strings with commas. For example: WlForwardPath=/weblogic,/bea.	ISAPI plug-in
KeepAliveSecs	20	The length of time after which an inactive connection between the plug-in and WebLogic Server is closed. You must set KeepAliveEnabled to true (ON when using the Apache plug-in) for this parameter to be effective. The value of this parameter must be less than or equal to the value of the Duration field set in the Administration Console on the Server/HTTP tab, or the value set on the server Mbean with the KeepAliveSecs attribute.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
KeepAliveEnabled	true (Microsoft IIS plug-in) ON (Apache plug-in)	Enables pooling of connections between the plug-in and WebLogic Server. Valid values for the Microsoft IIS plug-ins are true and false. Valid values for the Apache plug-in are ON and OFF.	ISAPI, Apache and NSAPI plug-in, HttpClusterServlet, and HttpProxyServlet
QueryFromRequest (Apache HTTP Server only)	OFF	When set to ON, specifies that the Apache plug-in use (request_rec *)r->the request to pass the query string to WebLogic Server. (For more information, see your Apache documentation.) This behavior is desirable in the following situations: When a Netscape version 4.x browser makes requests that contain spaces in the query string If you are using Raven Apache 1.5.2 on HP When set to OFF, the Apache plug-in uses (request_rec *)r->args to pass the query string to WebLogic Server.	Apache plug-in
MaxSkipTime	10	If a WebLogic Server listed in either the WebLogicCluster parameter or a dynamic cluster list returned from WebLogic Server fails, the failed server is marked as “bad” and the plug-in attempts to connect to the next server in the list. MaxSkips sets the amount of time after which the plug-in will retry the server marked as “bad.” The plug-in attempts to connect to a new server in the list each time a unique request is received (that is, a request without a cookie).	ISAPI, Apache and NSAPI plug-in, and HttpClusterServlet
DynamicServerList	ON	When set to OFF, the plug-in ignores the dynamic cluster list used for load balancing requests proxied from the plug-in and only uses the static list specified with the WebLogicCluster parameter. Normally this parameter should remain set to ON. There are some implications for setting this parameter to OFF: If one or more servers in the static list fails, the plug-in could waste time trying to connect to a dead server, resulting in decreased performance. If you add a new server to the cluster, the plug-in cannot proxy requests to the new server unless you redefine this parameter. WebLogic Server automatically adds new servers to the dynamic server list when they become part of the cluster.	NSAPI, ISAPI, and Apache plug-in, and HttpClusterServlet
WLProxySSL	OFF	Set this parameter to ON to maintain SSL communication between the plug-in and WebLogic Server when the following conditions exist: An HTTP client request specifies the HTTPS protocol The request is passed through one or more proxy servers (including the WebLogic Server proxy plug-ins) The connection between the plug-in and WebLogic Server uses the HTTP protocol When WLProxySSL is set to ON, the location header returned to the client from WebLogic Server specifies the HTTPS protocol.	NSAPI, ISAPI, and Apache plug-in, HttpClusterServlet, and HttpProxyServlet
WLLocalIP	none	Defines the IP address to bind to when the plug-in connects to a WebLogic Server instance running on a multihomed machine. If WLLocalIP is not set, a random IP address on the multi-homed machine is used.	NSAPI, ISAPI, and Apache plug-in
WLSendHdrSeparately	ON	When this parameter is set to ON, header and body of the response are sent in separate packets. Note: If you need to send the header and body of the response in two calls, for example, in cases where you have other ISAPI filters or programmatic clients that expect headers before the body, set this parameter to ON.	ISAPI plug-in

Location of POST Data Files

When the FileCaching parameter is set to ON, and the size of the POST data in a request is greater than 2048 bytes, the POST data is first read into a temporary file on disk and then forwarded to the WebLogic Server in chunks of 8192 bytes. This preserves the POST data during failover.

The temporary POST file is located under /tmp/_wl_proxy for UNIX. For Windows it is located as follows (if WLTempDir is not specified):

1. Environment variable TMP

2. Environment variable TEMP

3. C:\Temp

/tmp/_wl_proxy is a fixed directory and is owned by the HTTP Server user. When there are multiple HTTP Servers installed by different users, some HTTP Servers might not be able to write to this directory. This condition results in an error similar to the following:

@
@
@ <HTML>
@ <HEAD>
@ <TITLE>Weblogic Bridge Message
@ </TITLE>
@ </HEAD>
@  <BODY>
@ <H2>Failure of server APACHE bridge:</H2><P>
@ <hr>Cannot open TEMP post file '/tmp/_wl_proxy/_post_25444_36' for POST of
@ 4564 bytes

To correct this condition, use the WLTempDir parameter to specify a different location for the _wl_proxy directory for POST data files.

SSL Parameters for Web Server Plug-Ins

Note: SCG Certificates are not supported for use with WebLogic Server Proxy Plug-Ins. Non-SCG certificates work appropriately and allow SSL communication between WebLogic Server and the plug-in. KeyStore-related initialization parameters are not supported for use with WebLogic Server Proxy Plug-Ins

The SSL parameters for Web Server plug-ins are shown in Table 7-2. Parameters are case sensitive.

Table 7-2 SSL Parameters for Web Server Plug-Ins

Parameter	Default	Description	Applicable to
EnforceBasicConstraint	Strong	This parameter closes a security hole which existed with SSL certificate validation where certificate chains with invalid V3 CA certificates would not be properly rejected. This allowed certificate chains with invalid intermediate CA certificates, rooted with a valid CA certificate to be trusted. X509 V3 CA certificates are required to contain the BasicConstraints extension, marked as being a CA, and marked as a critical extension. This checking protects against non-CA certificates masquerading as intermediate CA certificates. The levels of enforcement are as follows: OFF This level entirely disables enforcement and is not recommended. Most current commercial CA certificates should work under the default STRONG setting. EnforceBasicConstraints=off EnforceBasicConstraints=false STRONG Default. The BasicConstraints for V3 CA certificates are checked and the certificates are verified to be CA certificates. EnforceBasicConstraints=strong EnforceBasicConstraints=true STRICT This level does the same checking as the STRONG level, but in addition it also strictly enforces IETF RFC 2459 which specifies the BasicConstraints for CA certificates also must be marked as "critical". This is not the default setting because a number of current commercially available CA certificates don't conform to RFC 2459 and don't mark the BasicConstraints as critical. Set this if you want to strict conformance to RFC 2459. EnforceBasicConstraints=strict	NSAPI, ISAPI, and Apache plug-in
SecureProxy	OFF	Set this parameter to ON to enable the use of the SSL protocol for all communication between the plug-in and WebLogic Server. Remember to configure a port on the corresponding WebLogic Server for the SSL protocol before defining this parameter. This parameter may be set at two levels: in the configuration for the main server and—if you have defined any virtual hosts—in the configuration for the virtual host. The configuration for the virtual host inherits the SSL configuration from the configuration of the main server if the setting is not overridden in the configuration for the virtual host.	ISAPI, NSAPI, and Apache plug-ins, HttpClusterServlet, and HttpProxyServlet
TrustedCAFile	none	Name of the file that contains the digital certificates for the trusted certificate authorities for the plug-in. This parameter is required if the SecureProxy parameter is set to ON.	ISAPI, NSAPI, and Apache plug-ins
RequireSSLHostMatch	true	Determines whether the host name to which the plug-in is connecting must match the Subject Distinguished Name field in the digital certificate of the WebLogic Server to which the proxy plug-in is connecting. When specifying SecureProxy=ON and RequireSSLHostMatch=true in the plug-in, then the value specified in the ListenAddress property should exactly match the hostname value specified in the certificate. When using the ExternalDNSName property for WebLogic Server and setting SecureProxy=ON and RequireSSLHostMatch=true in the plug-in, then the value specified in the ExternalDNSName property should exactly match the hostname value specified in the certificate.	ISAPI, NSAPI, and Apache plug-ins
SSLHostMatchOID	22	The ASN.1 Object ID (OID) that identifies which field in the Subject Distinguished Name of the peer digital certificate is to be used to perform the host match comparison. The default for this parameter corresponds to the CommonName field of the Subject Distinguished Name. Common OID values are: Sur Name—23 Common Name—22 Email—13 Organizational Unit—30 Organization—29 Locality—26	ISAPI, NSAPI, and Apache plug-ins
KeyStore	none	For generic proxy servlets, the key store location in a Web application when using two-way SSL to create a user-defined identity certificate and key.	Applies only to the HttpClusterServlet and to the HttpProxyServlet.
KeyStoreType	none	The key store type when using two-way SSL with a generic proxy servlet. If it is not defined, the default type will be used instead.	Applies only to the HttpClusterServlet and to the HttpProxyServlet.
PrivateKeyAlias	none	The private key alias when using two-way SSL with a generic proxy servlet.	Applies only to the HttpClusterServlet and to the HttpProxyServlet.
KeyStorePasswordProperties	none	A property file in a Web application that defines encrypted passwords to access the key store and private key alias when using two-way SSL with a generic proxy servlet. The file contents looks like this: KeyStorePassword={3DES}i4+50LCKenQO8BBvlsXTrg\=\= PrivateKeyPassword={3DES}a4TcG4mtVVBRKtZwH3p7yA\=\= You must use the weblogic.security.Encrypt command-line utility to encrypt the password. For more information on the Encrypt utility, as well as the CertGen, and der2pem utilities, see Using the Oracle WebLogic Server Java Utilities in the Oracle Fusion Middleware Command Reference for Oracle WebLogic Server.	Applies only to the HttpClusterServlet and to the HttpProxyServlet.