按照此过程将一个未封装的根 (/) 文件系统恢复到一个节点。不应引导正在恢复的节点。在执行此恢复过程前确保群集无故障运行。
由于必须使用失败的磁盘的格式来给新的磁盘进行分区,所以在进行此过程前必须识别 分区方案,并相应地重新创建文件系统。
更换要在其上恢复根文件的节点上失败的磁盘。
请参考服务器附带的文档中的磁盘更换过程。
引导要恢复的节点。
如果使用 Solaris CD-ROM,请运行以下命令:
ok boot cdrom -s |
如果使用一个 JumpStart 服务器,则运行以下命令:
ok boot net -s |
使用 format(1M) 命令在根磁盘上创建所有的分区和交换。
重建失败的磁盘上的原分区方案。
使用 newfs(1M) 命令,相应地创建根 (/) 文件系统和其他文件系统。
重建失败的磁盘上的原文件系统。
确保创建 /global/.devices/node@nodeid 文件系统。
在一个临时安装点上安装根 (/) 文件系统。
# mount device temp-mount-point |
从备份中恢复根 (/) 文件系统。
# cd temp-mount-point # ufsrestore rvf dump-device # rm restoresymtable |
创建一个空的 install-db 文件。
这会使节点在下次重新引导时进入 VxVM i安装模式。
# touch /temp-mount-point/etc/vx/reconfig.d/state.d/install-db |
从 /temp-mount-point/etc/system 文 件移除或注释掉下列项。
* rootdev:/pseudo/vxio@0:0 * set vxio:vol_rootdev_is_volume=1 |
编辑 /temp-mount-point/etc/vfstab 文 件并用根磁盘的标准磁盘设备替换所有的 VxVM 安装 点,如 /dev/dsk/c0t0d0s0。
Example: Change from- /dev/vx/dsk/rootdg/rootvol /dev/md/rdsk/rootdg/rootvol / ufs 1 no - Change to- /dev/dsk/c0t0d0s0 /dev/rdsk/c0t0d0s0 / ufs 1 no - |
卸载临时文件系统并检查该文件系统。
# cd / # umount temp-mount-point # fsck raw-disk-device |
在新的磁盘上安装引导块。
# /usr/sbin/installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk raw-disk-device |
以单用户模式重新引导节点。
# reboot -- "-s" |
使用 scdidadm(1M) 更新磁盘 ID。
# scdidadm -R /dev/rdsk/c0t0d0 |
运行 vxinstall。
# vxinstall |
选择封装磁盘并重新引导。
如果与其他系统间存在次编号冲突,则卸载全局设备并为磁盘组重编次编号。
卸载群集节点上的全局设备文件系统。
# umount /global/.devices/node@nodeid |
为群集节点上的 rootdg 磁盘组重编次编号。
# vxdg reminor rootdg 100 |
# shutdown -g0 -i 6 -y |
以下示例展示从磁带设备 /dev/rmt/0 恢复到 节点 phys-schost-1 的封装的根 (/) 文件系统。
[Replace the failed disk and boot the node:] ok boot cdrom -s [Use format and newfs to create partitions and file systems] [Mount the root file system on a temporary mount point:] # mount /dev/dsk/c0t0d0s0 /a [Restore the root file system:] # cd /a # ufsrestore rvf /dev/rmt/0 # rm restoresymtable [Create an empty install-db file:] # touch /a/etc/vx/reconfig.d/state.d/install-db [Edit /etc/system on the temporary file system and remove or comment out the following entries:] # rootdev:/pseudo/vxio@0:0 # set vxio:vol_rootdev_is_volume=1 [Edit /etc/vfstab on the temporary file system:] Example: Change from- /dev/vx/dsk/rootdg/rootvol /dev/md/rdsk/rootdg/rootvol / ufs 1 no- Change to- /dev/dsk/c0t0d0s0 /dev/rdsk/c0t0d0s0 / ufs 1 no - [Unmount the temporary file system, then check the file system:] # cd / # umount /a # fsck /dev/rdsk/c0t0d0s0 [Install a new boot block:] # /usr/sbin/installboot /usr/platform/`uname \ -i`/lib/fs/ufs/bootblk /dev/rdsk/c0t0d0s0 [Reboot in single-user mode:] # reboot -- "-s" [Update the disk ID:] # scdidadm -R /dev/rdsk/c0t0d0 [Run vxinstall:] # vxinstall Choose to encapsulate the root disk. [If there is a conflict in minor number, reminor the rootdg disk group:] # umount /global/.devices/node@nodeid # vxdg reminor rootdg 100 # shutdown -g0 -i 6 -y |