백업할 때 메타 장치에 있던 루트(/) 파일 시스템을 복원하려면 이 절차를 사용십시오. 루트 디스크가 손상되어 새 디스크로 교체하는 경우와 같은 상황에서 이 절차를 수행하십시오. 복원하는 노드를 부트하면 안됩니다. 복원 절차를 수행하기 전에 클러스터가 문제 없이 실행되는지 확인하십시오.
장애가 발생한 디스크와 동일한 형식을 사용하여 새 디스크를 분할해야 하기 때문에 이 절차를 시작하기 전에 파티션 구조를 확인 하고 필요한 파일 시스템을 다시 만드십시오.
복원하려는 노드를 제외한 노드 중에서 메타 세트에 액세스할 수 있는 클러스터 노드에 대하여 수퍼유저가 되십시오.
모든 메타 세트에서 복원되는 노드의 호스트 이름을 제거하십시오.
# metaset -s setname -f -d -h nodelist |
메타 세트 이름을 지정합니다.
강제 실행.
메타 세트에서 삭제합니다.
메타 세트에서 삭제할 노드의 이름을 지정합니다.
루트(/) 파일 시스템을 복원할 노드에서 장애가 발생한 디스크를 교체하십시오.
서버와 함께 제공되는 문서에서 디스크를 교체하는 절차를 참조하십시오.
복원되고 있는 노드를 부트하십시오.
Solaris CD-ROM을 사용할 경우에는 다음 명령을 실행하십시오.
ok boot cdrom -s |
JumpStart 서버를 사용하는 경우에는 다음 명령을 실행하십시오.
ok boot net -s |
format(1M) 명령을 사용하여 루트 디스크에 모든 파티션과 스왑 공간을 만드십시오.
장애가 발생한 디스크와 동일한 파티션 구조를 다시 만드십시오.
newfs(1M) 명령을 사용하여 루트(/)파일 시스템과 필요한 다른 파일 시스템을 만드십시오.
장애가 발생한 디스크와 동일한 파일 시스템을 다시 만드십시오.
/global/.devices/node@nodeid 파일 시스템을 만들어야 합니다.
임시 마운트 포인트에 루트(/) 파일 시스템을 마운트하십시오.
# mount device temp-mount-point |
다음 명령을 사용하여 루트(/) 파일 시스템을 복원하십시오.
# cd temp-mount-point # ufsrestore rvf dump-device # rm restoresymtable |
새 디스크에 새 부트 블록을 설치하십시오.
# /usr/sbin/installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk raw-disk-device |
/temp-mount-point/etc/system파일에서 MDD 루트 정보에 대한 다음 행을 제거하십시오.
* Begin MDD root info (do not edit) forceload: misc/md_trans forceload: misc/md_raid forceload: misc/md_mirror forceload: misc/md_hotspares forceload: misc/md_stripe forceload: drv/pcipsy forceload: drv/glm forceload: drv/sd rootdev:/pseudo/md@0:0,10,blk * End MDD root info (do not edit) |
/temp-mount-point/etc/vfstab 파일을 편집하여 메타 장치의 루트 항목을 메타 장치에 포함된 루트 디스크의 각 파일 시스템에 해당하는 일반 슬라이스로 변경하십시오.
Example: Change from- /dev/md/dsk/d10 /dev/md/rdsk/d10 / ufs 1 no - Change to- /dev/dsk/c0t0d0s0 /dev/rdsk/c0t0d0s0 /usr ufs 1 no - |
임시 파일 시스템 마운트를 해제하고 원시 디스크 장치를 확인하십시오.
# cd / # umount temp-mount-point # fsck raw-disk-device |
단일 사용자 모드로 노드를 다시 부트하십시오.
# reboot -- "-s" |
scdidadm 명령을 사용하여 디스크 ID를 교체하십시오.
# scdidadm -R rootdisk |
metadb(1M) 명령을 사용하여 상태 데이터베이스 복제를 다시 만드십시오.
# metadb -c copies -af raw-disk-device |
만들 복제 수를 지정합니다.
이름이 지정된 원시 디스크 장치에 초기 상태 데이터베이스 복제를 만듭니다.
클러스터 모드로 노드를 다시 부트하십시오.
복원된 노드가 아닌 다른 클러스터 노드에서 metaset(1M) 명령을 사용하여 복원된 노드를 모든 메타 세트에 추가하십시오.
phys-schost-2# metaset -s setname -a -h nodelist |
메타 세트를 만들어 추가합니다.
Solstice DiskSuite 문서의 설명에 따라 루트(/)에 대한 메타 장치/미러를 설정하십시오.
노드가 클러스터 모드로 다시 부트됩니다. 이제 클러스터를 사용할 준비가 되었습니다.
다음 예는 테이프 장치 /dev/rmt/0에서 노드 phys-schost-1로 복원되는 루트(/) 파일 시스템입니다. 노드 phys-schost-1을 제거하고 나중에 다시 디스크 세트 schost-1에 추가하기 위해 클러스터의 다른 노드 phys-schost-2에서 metaset 명령이 실행됩니다. 다른 명령은 모두 phys-schost-1에서 실행됩니다. 새 부트 블록은 /dev/rdsk/c0t0d0s0에 만들어지고 상태 데이터베이스 복제 세 개는 /dev/rdsk/c0t0d0s4 에 만들어집니다.
[Become superuser on a cluster node with access to the metaset,other than the node to be restored.] [Remove the node from the metaset:] phys-schost-2# metaset -s schost-1 -f -d -h phys-schost-1 [Replace the failed disk and boot the node:] ok boot cdrom -s [Use format and newfs to recreate partitions and file systems.] [Mount the root file system on a temporary mount point:] # mount /dev/dsk/c0t0d0s0 /a [Restore the root file system:] # cd /a # ufsrestore rvf /dev/rmt/0 # rm restoresymtable [Install a new boot block:] # /usr/sbin/installboot /usr/platform/`uname \ -i`/lib/fs/ufs/bootblk /dev/rdsk/c0t0d0s0 [Remove the lines in /temp-mount-point/etc/system file for MDD root information:] * Begin MDD root info (do not edit) forceload: misc/md_trans forceload: misc/md_raid forceload: misc/md_mirror forceload: misc/md_hotspares forceload: misc/md_stripe forceload: drv/pcipsy forceload: drv/glm forceload: drv/sd rootdev:/pseudo/md@0:0,10,blk * End MDD root info (do not edit) [Edit the /temp-mount-point/etc/vfstab file] Example: Change from- /dev/md/dsk/d10 /dev/md/rdsk/d10 / ufs 1 no - Change to- /dev/dsk/c0t0d0s0 /dev/rdsk/c0t0d0s0 /usr ufs 1 no - [Unmount the temporary file system and check the raw disk device:] # cd / # umount /a # fsck /dev/rdsk/c0t0d0s0 [Reboot in single-user mode:] # reboot -- "-s" [Replace the disk ID:] # scdidadm -R /dev/dsk/c0t0d0 [Recreate state database replicas:] # metadb -c 3 -af /dev/rdsk/c0t0d0s4 # reboot Type CTRL-d to boot into multiuser mode. [Add the node back to the metaset:] phys-schost-2# metaset -s schost-1 -a -h phys-schost-1 |