Node Attributes

Nodes are defined by many attributes, most of which are not accessible to mpadmin commands. Although you are not able to affect these attributes, it can be helpful to know of their existence and meaning; hence, they are listed and briefly described in Table 6-6.

Table 6-7 lists the Node-level attributes that can be set via mpadmin commands. However, the enabled and max_total_procs are the only node attributes that you can safely modify. See "enabled " and "max_total_procs" for details.

Table 6-6 Node Attributes That Cannot Be Set by the System Administrator

Attribute	Kind	Description
cpu_idle	Value	Percent of time CPU is idle.
cpu_iowait	Value	Percent of time CPU spent in I/O wait state.
cpu_kernel	Value	Percent of time CPU spent in kernel state.
cpu_swap	Value	Percent of time CPU spent waiting for swap.
cpu_type	Value	Type of CPU, for example, sparc.
cpu_user	Value	Percent of time CPU spends running user's program
load1	Value	Load average for the past minute.
load5	Value	Load average for the past five minutes.
load15	Value	Load average for the past 15 minutes.
manufacturer	Value	Manufacturer of the node, e.g., Sun_Microsystems.
mem_free	Value	Node's available RAM (in Mbytes).
mem_total	Value	Node's total physical memory (in Mbytes).
ncpus	Value	Number of CPUs in the node.
offline	Boolean	Set automatically by the system if the tm.spmd daemon on the node stops running or is unresponsive; if set, prevents jobs from being spawned on the node.
os_arch_kernel	Value	Node's kernel architecture (same as output from arch -k, for example, sun4u).
os_name	Value	Name of the operating system running on the node, for example, SunOS.
os_release	Value	Operating system's release number, for example, 5.5.1
os_release_maj	Value	Operating system's major release number, for example, 5.
os_release_min	Value	Operating system's minor release number, for example, 5 or 6.
os_version	Value	Operating system's version, for example, GENERIC.
serial_number	Value	Hardware serial number or host id.
swap_free	Value	Node's available swap space (in Mbytes).
swap_total	Value	Node's total swap space (in Mbytes).
update_time	Value	When this information was last updated.
update_time	Value	When this information was last updated.

Table 6-7 Node Attributes That Can Be Set by the System Administrator

Attribute	Kind	Description
enabled	Boolean	Set if the node is enabled, that is, if it is ready to accept jobs.
master	Boolean	Specify node on which the master daemons are running as an argument to mprun.
max_locked_mem	Value	Maximum amount of shared memory allowed to be locked down by Sun MPI processes (in Kbytes).
max_total_procs	Value	Maximum number of Sun HPC processes per node.
min_unlocked_mem	Value	Minimum amount of shared memory not to be locked down by Sun MPI processes (in Kbytes).
name	Value	Name of the node; this is predefined and must not be set via mpadmin.
partition	Value	Partition of which node is a member.
shmem_minfree	Value	Fraction of swap space kept free for non-MPI use.

enabled

The attribute enabled is set by default when the CRE daemons are start up on a node. Unsetting it prevents new jobs from being spawned on the node.

A partition can list a node that is not enabled as a member. However, jobs will execute on that partition as if that node were not a member.

master

---

Note -

You must not change this node attribute. The CRE automatically sets it to the hostname of the node on which the master CRE daemons are running. This happens whenever the CRE daemons start.

---

max_locked_mem and min_unlocked_mem

---

Note -

You should not change these node attributes. They are described here so that you will be able to interpret their values when node attributes are displayed via the dump or show commands.

---

The max_locked_mem and min_unlocked_mem attributes limit the amount of shared memory available to be locked down for use by Sun MPI processes. Locking down shared memory guarantees maximum speed for Sun MPI processes by eliminating delays caused by swapping memory to disk. However, locking physical memory can have undesirable side effects because it prevents that memory from being used by other processes on the node.

Solaris provides two related tunable kernel parameters:

• tune_t_minasmem, which is similar to min_unlocked_mem

• pages_pp_maximum, which is similar to max_locked_mem.

The CRE parameters impose limits only on MPI programs, while the kernel parameters limit all processes. Also, the kernel parameter units are pages rather than Kbytes. Refer to your Solaris documentation for more information about tune_t_minasmem and pages_pp_maximum.

max_total_procs

You limit the number of mprun processes allowed to run concurrently on a node by setting this attribute to an integer.

[node0]
P(part0):: set max_total_procs=10[node0] P(part0):: 

By default, max_total_procs is unset. The CRE does not impose any limit on the number of processes allowed on a node.

name

A node's name is predefined by the hpc.conf file. You must not change it by setting this attribute.

partition

---

Note -

There is no need to set this attribute. The CRE sets it automatically if the node is included in any partition configuration(s). See "Creating Partitions" for additional details.

---

A node can belong to multiple partitions, but only one of those partitions can be enabled at a time. No matter how many partitions a node belongs to, the partition attribute shows only one partition name--that name is always the name of the enabled partition, if one exists for that node.

shmem_minfree

---

Note -

You should not change this node attribute. It is described here so that you will be able to interpret its value when node attributes are displayed via the dump or show commands.

---

The shmem_minfree attribute reserves some portion of the /tmp file system for non-MPI use.

For example, if /tmp is 1 Gbyte and shmem_minfree is set to 0.2, any time free space on /tmp drops below 200 Mbytes (1 Gbyte * 0.2), programs using the MPI shared memory protocol will not be allowed to run.

[node0]
N(node1):: set shmem_minfree=0.2

shmem_minfree must be set to a value between 0.0 and 1.0. When shmem_minfree is unset, it defaults to 0.1.

This attribute can be set on both nodes and partitions. If both are set to different values, the node attribute overrides the partition attribute.