Documentation, Support, and Training
Understanding Switch Specifications
Understanding InfiniBand Cabling
Verify Shipping Carton Contents
Install the Switch in the Rack
Verifying the InfiniBand Fabric
Check Network Management Port Status LEDs
Check Power Supply Status LEDs
Understanding Routing Through the Switch
Switch Chip Port to QSFP Connectors and Link LED Routes
QSFP Connectors and Link LEDs to Switch Chip Port Routes
Signal Route Through the Switch
Understanding Administrative Commands
Display the State of the Chassis Status LEDs
Display Switch Environmental and Operational Data
Display Switch Firmware Versions
Display the Switch Chip Port to QSFP Connector Mapping
Locate a Switch Chip or Connector From the GUID
Display Switch Chip Boot Status
Display Switch Chip Port Status
Display Switch Chip Port Counters
Monitoring the InfiniBand Fabric
Identify All Switches in the Fabric
Identify All HCAs in the Fabric
Display the InfiniBand Fabric Topology (Simple)
Display the InfiniBand Fabric Topology (Detailed)
Display the Link Status of a Node
Display Data Counters for a Node
Display Low-Level Detailed Information About a Node
Display Low-Level Detailed Information About a Port
Display Recent Subnet Manager Activity
Display Subnet Manager Priority, Prefix, and Controlled Handover State
Display the Subnet Manager Log
Restart the Management Controller
Recover Ports After Switch Chip Reset
Change the Administrator Password
Controlling the InfiniBand Fabric
Perform Comprehensive Diagnostics for the Entire Fabric
Perform Comprehensive Diagnostics for a Route
Determine Changes to the InfiniBand Fabric Topology
Find 1x, SDR, or DDR Links in the Fabric
Determine Which Links Are Experiencing Significant Errors
Controlling the Subnet Manager
Set the Subnet Manager Priority
Enable Subnet Manager Controlled Handover
Understanding Oracle ILOM on the Switch
Understanding Oracle ILOM Targets
Installing the Oracle ILOM Firmware
Acquire the Oracle ILOM Firmware Version 1.1.3
Install the Oracle ILOM Firmware Version 1.1.3
Administering Oracle ILOM (CLI)
Accessing Oracle ILOM From the CLI
Switching Between the Oracle ILOM Shell and the Linux Shell
Monitoring Oracle ILOM Targets (CLI)
Controlling Oracle ILOM Targets (CLI)
Upgrading the Switch Firmware Through Oracle ILOM (CLI)
Administering Oracle ILOM (Web)
Access Oracle ILOM From the Web Interface
Monitoring Oracle ILOM Targets (Web)
Controlling Oracle ILOM Targets (Web)
Upgrading the Switch Firmware Through Oracle ILOM (Web)
Accessing the Rear Panel Diagram
Accessing Status Pane Information
Monitoring Parameters and Status
Administering Oracle ILOM (SNMP)
Monitoring Oracle ILOM Targets (SNMP)
Controlling Oracle ILOM Targets (SNMP)
Display the Sensors' State (IPMI)
Display the Sensor Information (IPMI)
Display the System Event Log (IPMI)
Display FRU ID Information (IPMI)
Display Switch Status LED States (IPMI)
Disable the Locator LED (IPMI)
Understanding Oracle ILOM Commands
Understanding Hardware Commands
Linux Shells for Hardware Commands
Understanding InfiniBand Commands
Linux Shells for InfiniBand Commands
Understanding the SUN-DCS-MIB MIB OIDs
Understanding the SUN-ILOM-CONTROL-MIB MIB OIDs
Understanding the SUN-PLATFORM-MIB MIB OIDs
Often you need to know the route between two nodes. The ibtracert command can provide that information by displaying the GUIDs, ports, and LIDs of the nodes along the route.
# ibtracert slid dlid
where:
slid is the LID of the source node.
dlid is the LID of the destination node.
For example:
# ibtracert 15 14 From switch {0x0021283a8389a0a0} portnum 0 lid 15-15 "Sun DCS 36 QDR switch localhost" [23] -> ca port {0x0003ba000100e38a}[2] lid 14-14 "nsn33-43 HCA-1" To ca {0x0003ba000100e388} portnum 2 lid 14-14 "nsn33-43 HCA-1" #
Note - The output for your InfiniBand fabric will differ from that in the example.
For this example:
The route starts at switch with GUID 0x0021283a8389a0a0 and is using port 0. The switch is LID 15. In the description, the switch host’s name is Sun DCS 36 QDR switch localhost.
The route enters at port 23 of the CA with GUID 0x0003ba000100e38a and exits at port 2. The CA is LID 14.
Switch Reference, ibtracert command