man pages section 1: User Commands

audiorecord(1)

Name

audiorecord– record an audio file

Synopsis

audiorecord [-af] [-v vol] [-b bal] [-m monvol] 
     [-p mic | line | internal-cd] [-c channels] [-s rate] 
     [-e encoding] [-t time] [-i info] [-d dev] 
     [-T au | aif[f] | wav] [file[.au|.aif[f]]|.wav]

Description

The audiorecord utility copies audio data from the audio device to a named audio file, or to the standard output if no filename is present. If no output file is specified and standard output is a tty, the volume, balance, monitor volume, port, and audio format settings specified on the command line will be applied and the program will exit.

By default, monaural audio data is recorded at 8 kHz and encoded in -law format. If the audio device supports additional configurations, the -c, -s, and -e options may be used to specify the data format. The output file is prefixed by an audio file header that identifies the format of the data encoded in the file.

Recording begins immediately and continues until a SIGINT signal (for example, Control-c) is received. If the -t option is specified, audiorecord stops when the specified quantity of data has been recorded.

If the audio device is unavailable, that is, if another process currently has read access, audiorecord prints an error message and exits immediately.

Options

The following options are supported:

-\?: Help: Prints a command line usage message.
-a: Append: Appends the data on the end of the named audio file. The audio device must support the audio data format of the existing file.
-b bal: Balance: The recording balance is set to the specified value before recording begins, and is reset to its previous level when audiorecord exits. The bal argument is an integer value between -100 and 100, inclusive. A value of -100 indicates left balance, 0 middle, and 100 right. If this argument is not specified, the input balance will remain at the level most recently set by any process.
-c channels: Channels: Specifies the number of audio channels (1 or 2). The value may be specified as an integer or as the string mono or stereo. The default value is mono.
-d dev: Device: The dev argument specifies an alternate audio device from which input should be taken. If the -d option is not specified, the AUDIODEV environment variable is consulted (see below). Otherwise, /dev/audio is used as the default audio device.
-e encoding: Encoding: Specifies the audio data encoding. This value may be one of ulaw, alaw, or linear. The default encoding is ulaw.
-f: Force: When the -a flag is specified, the sample rate of the audio device must match the sample rate at which the original file was recorded. If the -f flag is also specified, sample rate differences are ignored, with a warning message printed on the standard error.
-i info: Information: The `information' field of the output file header is set to the string specified by the info argument. This option cannot be specified in conjunction with the -a argument.
-m monvol: Monitor Volume: The input monitor volume is set to the specified value before recording begins, and is reset to its previous level when audiorecord exits. The monval argument is an integer value between 0 and 100, inclusive. A non-zero value allows a directly connected input source to be heard on the output speaker while recording is in-progress. If this argument is not specified, the monitor volume will remain at the level most recently set by any process.
-p mic | line | internal-cd: Input Port: Selects the mic, line, or internal-cd input as the source of the audio output signal. If this argument is not specified, the input port will remain unchanged. Please notice: Some systems will not support all possible input ports. If the named port does not exist, this option is ignored.
-s rate: Sample Rate: Specifies the sample rate, in samples per second. If a number is followed by the letter k, it is multiplied by 1000 (for example, 44.1k = 44100). The default sample rate is 8 kHz.
-t time: Time: The time argument specifies the maximum length of time to record. Time can be specified as a floating-point value, indicating the number of seconds, or in the form: hh:mm:ss.dd, where the hour and minute specifications are optional.
-T au | aif[f] | wav: Specifies the audio file type to create. If the -a option is used, the file type must match the file to which it is being appended. Regardless of the file suffix, the type will be set as specified in this option. If this option is not specified, the file suffix will determine the type.
-v vol: Volume: The recording gain is set to the specified value before recording begins, and is reset to its previous level when audiorecord exits. The vol argument is an integer value between 0 and 100, inclusive. If this argument is not specified, the input volume will remain at the level most recently set by any process.

Operands

file[.au|.aif[f]]|.wav

File Specification: The named audio file is rewritten, or appended. If no filename is present, and standard output is not a tty, or if the special filename “-” is specified, output is directed to the the standard output.

If the -T option is not specified, the file suffix will determine the type of file. If the suffix is not recognized, the default is .au. If the -T option is specified, that file type is used regardless of the file suffix.

Usage

See largefile(5) for the description of the behavior of audiorecord when encountering files greater than or equal to 2 Gbyte ( 2³¹ bytes).

Environment Variables

AUDIODEV: The full path name of the audio device to record from, if no -d argument is supplied. If the AUDIODEV variable is not set, /dev/audio is used.

Attributes

See attributes(5) for descriptions of the following attributes:

ATTRIBUTE TYPE	ATTRIBUTE VALUE
Architecture	SPARC, x86
Availability	SUNWauda
Interface Stability	Evolving