test

Solaris 10 5/09 发行说明

x86: ata 在引导过程中超时 (6586621)

在 Intel 多处理器系统上，ata 驱动程序可能会在系统引导过程中超时。当根设备所在的驱动器具有绑定到传统 ata 驱动程序的 HBA 控制器时，会出现这样的超时。在系统引导过程中，这样的超时会导致暂时挂起、硬挂起或出现紧急情况，控制台上会出现类似如下的消息：


scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: reset bus, target=0 lun=0
scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: early timeout, target=0 lun=0
gda: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0 (Disk0):
        Error for command 'read sector'   Error Level: Informational
gda: [ID 107833 kern.notice]           Sense Key: aborted command
gda: [ID 107833 kern.notice]           Vendor 'Gen-ATA ' error code: 0x3
gda: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0 (Disk0):
        Error for command 'read sector'   Error Level: Informational
gda: [ID 107833 kern.notice]           Sense Key: aborted command
gda: [ID 107833 kern.notice]           Vendor 'Gen-ATA ' error code: 0x3
scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: abort request, target=0 lun=0
scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: abort device, target=0 lun=0
scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: reset target, target=0 lun=0
scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: reset bus, target=0 lun=0
scsi: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0 (ata0):
        timeout: early timeout, target=0 lun=0
gda: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0 (Disk0):
        Error for command 'read sector'   Error Level: Informational
gda: [ID 107833 kern.notice]           Sense Key: aborted command
gda: [ID 107833 kern.notice]           Vendor 'Gen-ATA ' error code: 0x3
gda: [ID 107833 kern.warning] WARNING: /pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0 (Disk0):

解决方法：请选择以下解决方法之一：

注 –

为了避免性能下降，解决方法 3 或 4 只应在解决方法 5 尚不可用时临时使用。