大多数 1997 年后期以来生产的 IA 主板上的 BIOS 都支持 "El Torito" 标准,因而将 CD-ROM 驱动器识别为引导设备。
您安装 Solaris 软件想通过 提示 (1)行吗?
如果不想,请转到下一步。
要确定当前提示窗口的大小,请使用 stty(1) 命令。
如果能,确保使用系统 BIOS 的设置工具打开此 CD。
如果不能,将标为 Solaris 8 设备配置助理 Intel 体系结构 的软盘插入系统的软盘驱动器。
您也可以从 Solaris 驱动程序连接下载 Solaris 8 设备配置助理,网址是:http://soldc.sun.com/support/drivers。
将标有 Solaris 8 安装英文 Intel 平台版本 或 Solaris 8 多语言安装 Intel 平台版本 的 CD 插入系统的 CD-ROM 驱动器。
通过退出系统、关闭系统、再打开系统来引导系统。
如果您正在使用标为 Solaris 8 设备配置助理 Intel 体系结构 的软盘,消息:
Solaris Boot Sector Version 1 |
就显示在屏幕顶部。然后,显示类似如下的信息:
Solaris for x86 - Generic DCB Version 1.234 loading /solaris/boot.bin |
屏幕刷新并显示类似如下的信息:
SunOS Secondary Boot version 3.00 Solaris Intel Platform Edition Booting System Running Configuration Assistant... |
如果您仅使用标为 Solaris 8 安装英文 Intel 平台版本 或 Solaris 8 多语言安装 Intel 平台版本 的 CD,消息:
SunOS - Intel Platform Edition Primary Boot Subsystem, vsn 2.0 |
就会显示在屏幕顶部。然后,显示类似如下的信息:
SunOS Secondary Boot version 3.00 Solaris Intel Platform Edition Booting System Running Configuration Assistant... |
当显示"Solaris 设备配置助理"屏幕时,按 F2_继续。
显示含有以下消息的"总线枚举"屏幕:
Determining bus types and gathering hardware configuration data ... |
然后显示"正在扫描设备"屏幕。对系统设备进行扫描。扫描完成后,显示"已标识的设备"屏幕。
按 F2_继续。
显示"正在装入"屏幕,其中含有装入的用来引导系统的驱动程序的消息。几秒钟之后,显示"引导 Solaris"屏幕。
在"引导 Solaris"屏幕上,请选择 CD 并按 F2_继续。
如果您正在使用标为 Solaris 8 安装英文 Intel 平台版本 的 CD,但 Solaris Web Start 找不到 Solaris fdisk 分区,就会短暂显示"正在运行驱动程序"屏幕,随后显示类似如下的信息:
<<< Current Boot Parameters >>> Boot path: /pci@0,0/pci-ide@7,1/ide@1/sd@0,0:a Boot args: kernel/unix <<< Starting Installation >>> SunOS Release 5.8 Version Generic 32-bit Copyright 1983-2000 Sun Microsystems, Inc. All rights reserved. Configuring /dev and /devices Using RPC Bootparams for network configuration information. Solaris Web Start 3.0 installer English has been selected as the language in which to perform the install. Starting the Web Start 3.0 Solaris installer Solaris installer is searching the system's hard disks for a location to place the Solaris installer software. No suitable Solaris fdisk partition was found. Solaris Installer needs to create a Solaris fdisk partition on your root disk, c0d0, that is at least 395 MB. WARNING: All information on the disk will be lost. May the Solaris Installer create a Solaris fdisk [y,n,?] |
相反,如果您正在使用标为 Solaris 8 安装英文 Intel 平台版本 的 CD,但 Solaris Web Start 能找到 Solaris fdisk 分区,就会短暂显示"正在运行驱动程序"屏幕并随后显示类似如下的信息:
<<< Current Boot Parameters >>> Boot path: /pci@0,0/pci-ide@7,1/ide@1/sd@0,0:a Boot args: kernel/unix <<< Starting Installation >>> SunOS Release 5.8 Version Generic 32-bit Copyright 1983-2000 Sun Microsystems, Inc. All rights reserved. Configuring /dev and /devices Using RPC Bootparams for network configuration information. Solaris Web Start 3.0 installer English has been selected as the language in which to perform the install. Starting the Web Start 3.0 Solaris installer Solaris installer is searching the system's hard disks for a location to place the Solaris installer software. The default root disk is /dev/dsk/c0d0. The Solaris installer needs to format /dev/dsk/c0d0 to install Solaris. WARNING: ALL INFORMATION ON THE DISK WILL BE ERASED! Do you want to format /dev/dsk/c0d0? [y,n,?,q] |
如果使用标为 Solaris 8 多语言安装 Intel 平台版本 的 CD,则会显示类似如下的信息:
<<< Current Boot Parameters >>> Boot path: /pci@0,0/pci-ide@7,1/ide@1/sd@0,0:a Boot args: kernel/unix <<< Starting Installation >>> SunOS Release 5.8 Version Generic 32-bit Copyright 1983-2000 Sun Microsystems, Inc. All rights reserved. Configuring /dev and /devices Using RPC Bootparams for network configuration information. Solaris Web Start 3.0 installer The Solaris Installer can be run in English, or any of the following languages: 1) English 6) Japanese 2) German 7) Korean 3) Spanish 8) Swedish 4) French 9) Simplified_Chinese 5) Italian 10) Traditional_Chinese Select the language you want to use to run the installer: |
如果使用的是 Solaris 8 安装英文 Intel 平台版本 CD,则转到下一步。
如果使用的是 Solaris 8 多语言安装 Intel 平台版本 CD,请输入编号以选择用何种语言显示提示、消息和其他安装信息。
如果 Solaris Web Start 找不到 Solaris fdisk 分区,就会显示类似以下的信息 (以您选中的语言显示):
language_you_selected 已选为进行安装的语言环境。 启动 Web Start 3.0 Solaris 安装程序 Solaris 安装程序正在系统硬盘中搜索 存放 Solaris 安装程序软件的位置。 找不到合适的 Solaris fdisk 分区。 Solaris 安装程序需要在根磁盘 c0d0 下创建一个 Solaris fdisk 分区, 此分区至少有 395MB。 警告:磁盘上的所有信息将丢失。 Solaris 安装程序可以创建一个 fdisk 分区吗 [y,n,?] |
如果 Solaris Web Start 能找到 Solaris fdisk 分区,就会显示类似以下的信息 (以您选中的语言显示):
language_you_selected 已选为进行安装的语言环境。 启动 Web Start 3.0 Solaris 安装程序 Solaris 安装程序正在系统硬盘中搜索 存放 Solaris 安装程序软件的位置。 缺省根磁盘为 /dev/dsk/c0d0。 Solaris 安装程序需要格式化 /dev/dsk/c0d0 以安装 Solaris. 警告:磁盘上的所有信息将被清除! 格式化 /dev/dsk/c0d0 吗? [y,n,?,q] |
Solaris Web Start 能够找到 Solaris fdisk 分区吗?
如果能,请转到步骤 21。
如果不能,则在提示符下键入 y 并按回车键。
显示类似如下的信息:
Total disk size is 972 cylinders Cylinder size is 4032 (512 byte) blocks Cylinders Partition Status Type Start End Length % ========= ====== ============ ===== === ====== === 1 DOS12 0 7 8 1 SELECT ONE OF THE FOLLOWING: 1. Create a partition 2. Specify the active partition 3. Delete a partition 4. Exit (update disk configuration and exit) 5. Cancel (exit without updating disk configuration) Enter Selection: |
键入 1 并按回车键。
显示类似如下的信息:
Select the partition type to create: 1=SOLARIS 2=UNIX 3=PCIXOS 4=Other 5=DOS12 6=DOS16 7=DOSEXT 8=DOSBIG A=x86 Boot B=Diagnostic 0=Exit? |
键入 A 并按回车键。
显示类似如下的信息:
Specify the percentage of disk to use for this partition (or type "c" to specify the size in cylinders). |
键入您想要的百分比并按回车键。
显示类似如下的信息:
Should this become the active partition? If yes, it will be activated each time the computer is reset or turned on. Please type "y" or "n". |
键入 y 并按回车键。
显示类似如下的信息:
Partition 2 is now the active partition. SELECT ONE OF THE FOLLOWING: 1. Create a partition 2. Specify the active partition 3. Delete a partition 4. Exit (update disk configuration and exit) 5. Cancel (exit without updating disk configuration) |
键入 1 并按回车键。
显示类似如下的信息:
Select the partition type to create: 1=SOLARIS 2=UNIX 3=PCIXOS 4=Other 5=DOS12 6=DOS16 7=DOSEXT 8=DOSBIG A=x86 Boot B=Diagnostic 0=Exit? |
键入 1 并按回车键。
显示类似如下的信息:
Specify the percentage of disk to use for this partition (or type "c" to specify the size in cylinders). |
键入您想要的百分比并按回车键。
显示类似如下的信息:
Should this become the active partition? If yes, it will be activated each time the computer is reset or turned on. Please type "y" or "n". |
键入 n 并按回车键。
创建了一个 IA 引导分区和 Solaris 分区。显示类似如下的信息:
Total disk size is 972 cylinders Cylinder size is 4032 (512 byte) blocks Cylinders Partition Status Type Start End Length % ========= ====== ============ ===== === ====== === 1 DOS12 0 7 8 1 2 Active x86 Boot 8 16 9 1 3 Solaris 17 969 953 98 SELECT ONE OF THE FOLLOWING: 1. Create a partition 2. Specify the active partition 3. Delete a partition 4. Exit (update disk configuration and exit) 5. Cancel (exit without updating disk configuration) Enter Selection: |
键入 4 并按回车键。
显示类似如下的信息:
找不到合适的 Solaris fdisk 分区。 Solaris 安装程序需要在根磁盘 c0d0 下创建一个 Solaris fdisk 分区,此分区至少有 395 MB 警告:磁盘上的所有信息将丢失。 Solaris 安装程序可以创建一个Solaris fdisk 分区吗? [y,n,?] |
键入 n 并按回车键。
显示类似如下的信息:
选择另外的安装程序选项。 查看更多的信息,参见 Solaris 安装程序文档。 要重新启动安装,可运行 /sbin/cd0_install。 |
在系统提示符下,键入 /sbin/cd0_install 并按回车键。
显示类似如下的信息:
缺省根磁盘为 /dev/dsk/c0d0。 Solaris 安装程序需要格式化 /dev/dsk/c0d0 以安装 Solaris. 警告:磁盘上的所有信息将被清除! 是否要格式化 /dev/dsk/c0d0? [y,n,?,q] |
在提示符下键入 y 并按回车键。
显示类似如下的信息:
说明:交换区的大小在文件系统布局过程中不会更改。 输入交换分区的大小,其值介于 384MB 和 1865MB 之间, 缺省值 = 512MB [?] |
在提示符下,按回车键接受缺省交换分区大小,或键入您希望的交换分区大小并按回车键。
显示类似如下的信息:
安装程序将在磁盘的起始放置交换分区。 这将在稍后的安装中允许最灵活的文件系统分区。 交换分区能在磁盘的起始开始吗? [y,n,?,q] |
您想将交换分区空间放到磁盘的开始 (这样可以增加划分文件系统的灵活性并提高访问磁盘的效率) 吗?
如果想,请键入 y,按回车键并转到步骤 25。
如果不想,则键入 n 并按回车键。
显示类似如下的信息:
警告:将交换片放到柱面 3 以外的柱面位置 需要有关于磁盘布局的专业知识。此类选 项以后可能会影响安装中的磁盘布局选项。 输入一个起始柱面, 其值介于在 3 和 590, 缺省值 = 3 [?] |
按回车键以接受缺省的起始柱面 (3),或键入您想要的起始柱面并按回车键。
显示类似如下的信息:
Solaris 安装程序要使用的项已经选择如下: 磁盘片 : /dev/dsk/c0d0 尺寸 : 512 MB 起始柱面 : 3 警告:磁盘上的所有信息将被清除! 是否正确? [y,n,?,q] |
在提示符下键入 y 并按回车键。
显示类似如下的信息:
Solaris 安装程序将使用磁盘分区 /dev/dsk/c0d0s1。 文件复制完毕后,系统将自动重新引导,而且 会继续进行安装。 请稍候... 拷贝 mini-root 到本地磁盘....完成。 拷贝平台相关文件....完成。 预备重新引导以继续安装程序。 需要重引导以继续安装程序。 请移开引导媒体(软盘或CD-ROM)并按回车。 注意:如果引导媒体是CD-ROM,则必须等待系统 重新启动以弹出光盘。 |
在步骤 2中,您将标为 Solaris 8 设备配置助理 Intel 体系结构 的软盘插入系统的软盘驱动器了吗?
如果插入了,请将它从系统的软盘驱动器中弹出并按回车键。
如果没有,请按回车键。
显示类似如下的信息:
Syncing file systems... 49 done rebooting... |
系统重置,并执行内存测试和硬件检测。
在系统完成内存测试和硬件检测之前,迅速将 Solaris 8 安装英文 Intel 平台版本 或 Solaris 8 多语言安装 Intel 平台版本 CD 从 CD-ROM 驱动器中弹出。
显示类似如下的信息:
SunOS - Intel Platform Edition Primary Boot Subsystem, vsn 2.0 Current Disk Partition Information Part# Status Type Start Length ================================================ 1 DOS12 63 32193 2 Active X86 BOOT 32256 36288 3 SOLARIS 68544 3842496 4 <unused> Please select the partition you wish to boot: |
几秒钟之后,刷新屏幕并显示类似如下的信息:
SunOS Secondary Boot version 3.00 Solaris Intel Platform Edition Booting System Running Configuration Assistant... Autobooting from bootpath /pci@0,0/pci-ide@7,1/ata@1/cmdk@0,0:b If the system hardware has changed, or to boot from a different device, interrupt the autoboot process by pressing ESC. Initializing system Please wait... <<< Current Boot Parameters >>> Boot path: /pci@0,0/pci-ide@7,1/ata@1/cmdk@0,0:b Boot args: Type b [file-name] [boot-flags] <ENTER> to boot with options or i <ENTER> to enter boot interpreter or <ENTER> to boot with defaults <<< timeout in 5 seconds >>> Select (b)oot or (i)nterpreter: SunOS Release 5.8 Version Generic 32-bit Copyright 1983-2000 Sun Microsystems, Inc. All rights reserved. Configuring /dev and /devices Using RPC Bootparams for network configuration information. |
然后,显示"Solaris 安装程序"屏幕。
按 F2_继续。
显示"kdmconfig - 介绍"屏幕。
按 F2_继续。
显示"kdmconfig - 查看和编辑视窗系统配置"屏幕。
检查"kdmconfig - 查看和编辑视窗系统配置"屏幕上的配置信息并按需要进行更改。
完成后,请选择"不需要更改 - 测试/保存并退出",并按 F2_继续。
显示"kdmconfig 视窗系统配置测试"屏幕。
按 F2_继续。
在显示的屏幕上,设法移动指针并检查调色板上的颜色,以确保颜色显示正确。