test

Solaris 8 2/02 Release Notes Supplement for Sun Hardware

Netra T4/Netra T20 Issues

System Incorrectly Reports Removed Device Links (BugID 4418718)

When calling luxadm remove_device /dev/rdsk/c1t1d0s2, the system asks for confirmation and reports that the disk is spinning down and being taken offline. When the disk is removed, pressing Return causes the system to report that the device links are removed.

However, the device links are not removed. The disk can then be re-inserted and used without running the luxadm insert_device command. When the command is subsequently run, the system reports that no new devices were added and the following message is produced at the console:

bash-2.03# luxadm remove_device /dev/rdsk/c1t1d0s2 

 

WARNING!!! Please ensure that no filesystems are mounted on these device(s). 

All data on these devices should have been backed up. 

 

The list of devices which will be removed is: 

1: Device name: /dev/rdsk/c1t1d0s2 

Node WWN: 2000002037e367e4 

Device Type:Disk device 

Device Paths: 

/dev/rdsk/c1t1d0s2 

 

Please verify the above list of devices and 

then enter 'c' or <CR> to Continue or 'q' to Quit. [Default: c]:  

stopping: /dev/rdsk/c1t1d0s2....Done 

offlining: /dev/rdsk/c1t1d0s2....Done 

 

Hit <Return> after removing the device(s)  

 

Device: /dev/rdsk/c1t1d0s2 

Logical Nodes being removed under /dev/dsk/ and /dev/rdsk: 

c1t1d0s0 

c1t1d0s1 

c1t1d0s2 

c1t1d0s3 

c1t1d0s4 

c1t1d0s5 

c1t1d0s6 

c1t1d0s7 

 

Device: /dev/rdsk/c1t1d0s2 

Logical Nodes being removed under /dev/dsk/ and /dev/rdsk: 

c1t1d0s0 

c1t1d0s1 

c1t1d0s2 

c1t1d0s3 

c1t1d0s4 

c1t1d0s5 

c1t1d0s6 

c1t1d0s7 

 

bash-2.03# ls -l /dev/dsk/c1t1* 

lrwxrwxrwx 1 root root 70 May 4 19:07 /dev/dsk/c1t1d0s0 -> ../../devices/pci@8,600000/SUNW,qlc@4/fp@0,0/ssd@w2100002037e367e4,0:a 

lrwxrwxrwx 1 root root 70 May 4 19:07 /dev/dsk/c1t1d0s1 -> ../../devices/pci@8,600000/SUNW,qlc@4/fp@0,0/ssd@w2100002037e367e4,0:b 

 

bash-2.03# ls -l /dev/rdsk/c1t1* 

lrwxrwxrwx 1 root root 74 May 4 19:07 /dev/rdsk/c1t1d0s0 -> ../../devices/pci@8,600000/SUNW,qlc@4/fp@0,0/ssd@w2100002037e367e4,0:a,raw 

lrwxrwxrwx 1 root root 74 May 4 19:07 /dev/rdsk/c1t1d0s7 -> ../../devices/pci@8,600000/SUNW,qlc@4/fp@0,0/ssd@w2100002037e367e4,0:h,raw 

. 

. 

/* the following errors are caused by SUNWvts reprobe looking for said disk */ 

 

bash-2.03#  

8012 05/22/01 14:05:07 Failed on iotcl DKIOCGMEDIAINFO: 6: No such device or address 

 

8012 05/22/01 14:05:41 Failed on iotcl DKIOCGMEDIAINFO: 6: No such device or address 

 

8012 05/22/01 14:07:25 Failed on iotcl DKIOCGMEDIAINFO: 6: No such device or address 

 

bash-2.03# luxadm insert_device 

Please hit <RETURN> when you have finished adding Fibre Channel Enclosure(s)/Device(s):  

 

Waiting for Loop Initialization to complete... 

No new device(s) were added!! 

 

To work around, enter the following when luxadm remove_device claims to have completed successfully:


# devfsadm -C -c disk

Not All USB Zip Drives Found (BugID 4453787)

If four USB Iomega zip drives are attached, prtconf indicates that no driver is loaded after the system has booted. drvconf starts a system probe that finds only two of the four USB zip drives.

Running cat on the /dev/usb/hub0 file causes the system to add the two zip drives.

Workaround: Do not use more than two zip drives in the current release.

LOMlite2 reset-x Does Not Reset CPUs (BugID 4462131)

The LOMlite2 reset-x command does not currently reset the CPUs. Look for this functionality in a later revision of the OpenBoot PROM.