The following list is subject to change at any time. For the latest bug and patch information, refer to:
http://sunsolve5.sun.com/sunsolve/Enterprise-dr.
The memory test should give occasional indications that it is still running. During a long test, the user cannot easily determine that the system is not hanging.
Workaround: Monitor system progress in another shell or window, using vmstat(1M), ps(1), or similar shell commands.
Memory interleaving is left in an incorrect state when a Sun Enterprise x500 server is rebooted after a Fatal Reset. Subsequent DR operations fail. The problem only occurs on systems with memory interleaving set to min.
Workarounds: Two choices are listed below.
To avoid the problem before it occurs, set the NVRAM memory-interleave property to max.
This causes memory to be interleaved whenever the system is booted. However, you may find this option to be unacceptable, as a memory board containing interleaved memory cannot be dynamically unconfigured. See DR: Cannot Unconfigure a CPU/Memory Board That Has Interleaved Memory (BugID 4210234).
vmstat shows an unusually high number of interrupts after configuring CPUs. With vmstat in the background, the interrupt field becomes abnormally large (but this does not indicate a problem exists). In the last row in the example below, the interrupts (in) column has a value of 4294967216:
# procs memory page disk faults cpu r b w swap free re mf pi po fr de sr s6 s9 s1 -- in sy cs us sy id 0 0 0 437208 146424 0 1 4 0 0 0 0 0 1 0 0 50 65 79 0 1 99 0 0 0 413864 111056 0 0 0 0 0 0 0 0 0 0 0 198 137 214 0 3 97 0 0 0 413864 111056 0 0 0 0 0 0 0 0 0 0 0 286 101 200 0 3 97 0 0 0 413864 111072 0 11 0 0 0 0 0 0 1 0 0 4294967216 43 68 0 0 100 |
Workaround: Restart vmstat.
Cannot unconfigure a CPU/memory board that has interleaved memory.
To unconfigure and subsequently disconnect a CPU board with memory or a memory‐only board, it is necessary to first unconfigure the memory. However, if the memory on the board is interleaved with memory on other boards, the memory cannot currently be unconfigured dynamically.
Memory interleaving can be displayed using the prtdiag or the cfgadm commands.
Workaround: Shut down the system before servicing the board, then reboot afterward. To permit future DR operations on the CPU/memory board, set the NVRAM memory-interleave property to min. See also Memory Interleaving Set Incorrectly After a Fatal Reset (BugID 4156075) for a related discussion on interleaved memory.
To unconfigure and subsequently disconnect a CPU board with memory or a memory-only board, it is necessary to first unconfigure the memory. However, some memory is not currently relocatable. This memory is considered permanent.
Permanent memory on a board is marked “permanent” in the cfgadm status display:
# cfgadm -s cols=ap_id:type:info Ap_Id Type Information ac0:bank0 memory slot3 64Mb base 0x0 permanent ac0:bank1 memory slot3 empty ac1:bank0 memory slot5 empty ac1:bank1 memory slot5 64Mb base 0x40000000 |
In this example, the board in slot3 has permanent memory and so cannot be removed.
Workaround: Shut down the system before servicing the board, then reboot afterward.
If a cfgadm process is running on one board, an attempt to simultaneously disconnect a second board fails.
A cfgadm disconnect operation fails if another cfgadm process is already running on a different board. The message is:
cfgadm: Hardware specific failure: disconnect failed: nexus error during detach: address |
Workaround: Do only one cfgadm operation at a time. If a cfgadm operation is running on one board, wait for it to finish before you start a cfgadm disconnect operation on a second board.
A server configured as a boot server for Solaris 2.5.1-based Intel platform clients has several rpld jobs running, whether or not such devices are in use. These active references prevent DR operations from detaching these devices.
Workaround: Perform a DR detach operation: