This chapter describes problems that relate to the installation of the Solaris 8 2/04 operating environment.
The following installation bug descriptions have been added to this chapter since this document was published on the Solaris 8 2/04 Documentation CD and in the Installation Kiosk on the Solaris 8 2/04 Installation CD.
Initial Install Might Not Be Possible If Swap Slice Does Not Start At Cylinder 0 (4508297)
Default Install Might Be Disabled If Swap Slice Is Not on The Default Boot Disk (4527984)
awk and nawk Field Limitation Might Cause Installation of Additional Software to Fail (4533901)
Solaris Web Start Installation Kiosk Menu Not Localized for European Locales (4510925)
The name of this product is Solaris 8 2/04 , but code and path or package path names might use Solaris 2.8 or SunOSTM 5.8. Always follow the code or path as it is written.
The Solaris 8 2/04 operating environment is now available on DVD. To install or upgrade from DVD, insert the Solaris 8 2/04 DVD into the DVD-ROM drive and boot the system from the ok prompt with the following command.
ok boot cdrom |
If your system has a Toshiba SD-M1401 DVD-ROM drive with firmware revision 1007, the system cannot boot from the Solaris 8 2/04 DVD.
Workaround: Apply patch 111649 to update the Toshiba SD-M1401 DVD-ROM drive's firmware. Patch 111649 is included on the Solaris 8 Supplement CD in the following directory.
DVD_Firmware/Patches |
See the README file in this directory for instructions on installing the patch. Be sure to read and follow all the cautions and warnings in this README file before you install the patch.
If your system is running the Solaris 2.6 or Solaris 7 operating environment, Volume Management incorrectly mounts the Solaris 8 2/04 DVD. The Solaris 8 2/04 DVD will mount, but the data is inaccessible. As a result, you cannot setup an install server, perform a Live Upgrade, or access any data on the media.
Workaround: Choose one of the following workarounds.
Apply the patches appropriate for your system.
Table 1–1 DVD patches for the Solaris 2.6 and Solaris 7 Operating Environments
Release |
Patch ID |
---|---|
Solaris 2.6 operating environment |
107618-03 |
Solaris 7 operating environment |
107259-03 |
Manually mount the Solaris 8 2/04 DVD. Do not use Volume Management to mount the Solaris 8 2/04 DVD. Follow these steps.
Become superuser.
Stop Volume Management.
# /etc/init.d/volmgt stop |
Manually mount the DVD.
# mkdir /mnt1 # mount -F hsfs -o ro /dev/dsk/c0t6d0s0 /mnt1 |
Verify that the DVD is mounted and the data is accessible.
# cd /mnt1 # ls |
The system returns the following information if the DVD is correctly mounted.
Copyright Solaris_8 |
When you install from the Solaris 8 Installation CD, the SolarisTM Web Start installation program might prompt you to use an existing swap slice to hold the installation software. However, the installation program does not indicate whether the existing swap slice starts at cylinder 0 or not. If you choose to use this slice and it does not begin at cylinder 0, installation might not be possible on some disk configurations.
Workaround: If you intend to perform an initial install, follow these steps.
This will prevent any file system preservations on the disk.
During setup, answer No to all questions that prompt you to use an existing swap slice.
If prompted, select None from the list of alternatives, then answer No when you are prompted to re-select a slice to hold the Solaris installation software.
Select a disk to re-partition when you are prompted by the installer.
Choose a size when you are prompted to provide a size for the swap slice.
When the installer asks if the swap slice can start at the beginning of the disk, answer Yes.
Complete the installation.
For more information on re-partitioning disks or choosing a size for the swap slice, see the Solaris 8 Advanced Installation Guide.
When you install from the Solaris 8 Installation CD and you choose a swap slice that is not on the default boot disk, the Default Install selection might be disabled. This problem can occur even when the swap slice starts at cylinder 0 and the default boot disk contains sufficient space for a Default Install. The following error message is displayed.
Note:Default install is not possible.The file system requires manual layout. |
Workaround: Choose one of the following workarounds.
If you are performing an initial install, choose the default boot disk as the location for the swap slice.
Perform a Custom Install if your swap slice is not located on the default boot disk.
A network gateway is used to communicate with other networks. A gateway system contains multiple network interface adapters and each adapter connects with a different network.
If you use the Solaris 8 Installation CD to install the Solaris 8 2/04 operating environment on a gateway system, Solaris Web Start 3.0 uses the primary interface to gather system information. You cannot instruct Solaris Web Start 3.0 to use an alternate network interface to gather information for system identification.
Workaround: To specify another interface for gathering system information, choose one of the following workarounds.
Create a sysidcfg file that specifies the network interface to use during system identification. See “Guidelines for Preconfiguring With the sysidcfg File” in Solaris 8 Advanced Installation Guide and the man page sysidcfg(4) for information on how to create and modify a sysidcfg file.
Use the Solaris 8 Software 1 of 2 CD to launch an Interactive Installation of the Solaris 8 2/04 operating environment. Specify that the system is networked, and then select the alternate network interface to use for system identification from the list that is provided.
When you upgrade from the Solaris 2.6 and Solaris 7 operating environments using a CD or CD images, extra European languages might be installed for locales that are not present on the system. If there is insufficient space in the file system, the upgrade will not complete. Languages for locales that are present on the system may not be installed.
Workaround: Choose one of the following workarounds.
Manually select the languages you want installed during the upgrade process. Follow these steps.
When the Language CD install panel is displayed, click the Back button.
Deselect the extra languages and continue with the upgrade.
Use a combined net install image to upgrade from the Solaris 2.6 and Solaris 7 operating environments. Do not use CDs or CD images to upgrade.
After upgrading, follow these steps.
Login to the system.
Run prodreg.
Uninstall any extra languages.
Insert the Language CD into your CD-ROM drive and run the top level installer.
Choose Custom Install.
Select the languages you want installed.
Complete the Language CD installation by clicking the Next and Install Now buttons.
If you upgrade to the Solaris 8 2/04 , or compatible, operating environment and you have Solaris Management ConsoleTM 1.0, 1.0.1, or 1.0.2 software installed, you must uninstall the Solaris Management Console software before you upgrade. Solaris Management Console 2.0 software is not compatible with any previous version of the console. Solaris Management Console software might exist on your system if you installed the SEAS 2.0 overbox, the SEAS 3.0 overbox, or the Solaris 8 Admin Pack.
Workaround: Choose one of the following workarounds.
Before you upgrade, run /usr/bin/prodreg and perform a full uninstall of the Solaris Management Console software.
If you did not uninstall Solaris Management Console 1.0, 1.0.1, or 1.0.2 software before you upgraded, you must remove all Solaris Management Console 1.0, 1.0.1., or 1.0.2 software packages. You must use pkgrm for package removal instead of prodreg and you must carefully follow the order of package removal. Follow these steps.
Become superuser.
In a terminal window, type the following commands.
# pkginfo |grep "Solaris Management Console" # pkginfo |grep "Solaris Management Applications" # pkginfo |grep "Solaris Diskless Client Management Application" |
The package names in the output identify a Solaris Management Console 1.0 software package if the description does not start with “Solaris Management Console 2.0.”
Use pkgrm to remove all instances of Solaris Management Console 1.0 software packages in the following order.
Do not remove any package that has “Solaris Management Console 2.0” in the description. For example, SUNWmc.2 might indicate the Solaris Management Console 2.0 software.
If the pkginfo output displays multiple versions of Solaris Management Console 1.0 software packages, use pkgrm to remove both packages. Remove the original package first and then the package that has been appended with a number. For example, if the SUNWmcman and SUNWmcman.2 packages appear in the pkginfo output, first remove SUNWmcman and then SUNWmcman.2. Do not use prodreg.
# pkgrm SUNWmcman # pkgrm SUNWmcapp # pkgrm SUNWmcsvr # pkgrm SUNWmcsvu # pkgrm SUNWmc # pkgrm SUNWmcc # pkgrm SUNWmcsws |
In a terminal window, type the following command.
# rm -rf /var/sadm/pkg/SUNWmcapp |
The Solaris Management Console 2.0 software should now function. For future maintenance, or if the console does not function properly, remove the Solaris Management Console 2.0 software and reinstall it by following the next steps.
In a terminal window type the following commands.
# pkginfo |grep "Solaris Management Console" # pkginfo |grep "Solaris Management Applications" # pkginfo |grep "Solaris Diskless Client Management Application" |
The package names in the output identify the remaining Solaris Management Console software packages that are installed on your system.
Use pkgrm to remove all Solaris Management Console 2.0 software packages in the following order.
If your system has multiple instances of Solaris Management Console 2.0 software packages, such as SUNWmc and SUNWmc.2, first remove SUNWmc, and then SUNWmc.2. Do not use prodreg.
# pkgrm SUNWdclnt # pkgrm SUNWmga # pkgrm SUNWmgapp # pkgrm SUNWmcdev # pkgrm SUNWmcex # pkgrm SUNWwbmc # pkgrm SUNWmc # pkgrm SUNWmcc # pkgrm SUNWmccom |
Insert the Solaris 8 Software (SPARC Platform Edition) 1 of 2 CD into your CD-ROM drive and type the following in a terminal window.
# cd /cdrom/sol_8_204_sparc/s0/Solaris_8/Product # pkgadd -d . SUNWmccom SUNWmcc SUNWmc SUNWwbmc SUNWmcex SUNWmcdev \ SUNWmgapp SUNWmga SUNWdclnt |
All previous versions of the Solaris Management Console software are now removed and the Solaris Management Console 2.0 software is functional.
The locale support installation mechanism has changed in the Solaris 8 operating environment. In the Solaris 2.5.1, 2.6, and 7 operating environments, the level of locale support that was installed depended on the software cluster that was chosen. The Solaris 8 operating environment includes a new installation interface that prompts you to select specific geographic regions for which you require locale support. Therefore, you can customize the configuration of your system at installation of the Solaris 8 operating environment with more freedom than in the Solaris 2.5.1, 2.6, and 7 operating environments.
Notice especially the following behaviors:
You must select the locales to be installed during the initial installation in the Geographic Selection screen. C (POSIX locale) and en_US.UTF-8 (Unicode support) are the only locales that are automatically installed.
When you upgrade from previous releases, some of the locales are automatically selected, depending on the available locales on the system to be upgraded. Note that English, French, German, Italian, Spanish, and Swedish partial locales were always present on the system in the Solaris 2.5.1, 2.6, and 7 operating environments.
Unicode locales (UTF-8) have a feature to enable multilingual text input. Because these locales use Asian input methods that are provided by each individual locale, install those Asian locales for which you need to type text.
If you install using the custom JumpStartTM program or the re-preinstall command, when the Solaris 8 Software 1 of 2 CD completes, the Solaris 8 Software 2 of 2 CD installation program does not automatically start. The system will reboot normally, but the installation is not complete.
Workaround: If you are performing a custom JumpStart installation, or you are using the re-preinstall command, choose one of the following workarounds.
Use a combined network image of the Solaris 8 Software CDs to perform the installation.
After the installation program on the Solaris 8 Software 1 of 2 CD completes, follow these steps.
Login as superuser.
Verify that the file /var/sadm/system/data/packages_to_be_added exists. Type the following command.
# ls /var/sadm/system/data/ |
If the file packages_to_be_added is listed in the output of the ls command, go to the next step.
If the output of the ls command does not list packages_to_be_added, your installation is complete. Do not continue with the workaround.
Insert the Solaris 8 Software 2 of 2 CD into the CD-ROM drive and type the following commands to start the installation program.
# volcheck # cd /cdrom/cdrom0/Solaris_8/Tools/Installers # ./solaris2 |
After the Solaris 8 Software 2 of 2 installation completes, type the following command to determine if /var/sadm/system/data/packages_to_be_added exists.
# ls /var/sadm/system/data |
If the file packages_to_be_added is listed in the output of the ls command, go to the next step.
If the output of the ls command does not list packages_to_be_added, your installation is complete. Do not continue with the workaround.
Insert the Solaris 8 Languages CD into the CD-ROM drive and type the following commands.
# volcheck # cd /cdrom/cdrom0 # ./installer |
Choose the custom installation path in the Solaris 8 Languages CD installation program.
Select the languages that you require for your system and complete the installation.
If you have more than one CD-ROM drive, the path might be /cdrom/cdrom#, where cdrom# is the CD-ROM drive into which you inserted the Solaris 8 Software 2 of 2 CD, or the Solaris 8 Languages CD.
The Installing Solaris Software - Progress bar sometimes indicates that an installation is complete when it is still in progress. The installation program might add packages for several minutes after the progress bar has indicated that the installation is complete.
Do not rely on the progress bar to indicate that the installation is complete. The installation displays the following message when the program has completed all installation operations.
Installation complete |
One of the following warning messages might be displayed when a file system is created during installation.
Warning: inode blocks/cyl group (87) >= data blocks (63) in last cylinder group. This implies 1008 sector(s) cannot be allocated. |
Or
Warning: 1 sector(s) in last cylinder unallocated |
The warning occurs when the size of the file system that is being created does not map exactly to the space on the disk that is being used. This discrepancy can result in unused space on the disk that is not incorporated into the indicated file system. This unused space is not available for use by other file systems.
Workaround: Ignore the warning message.
After you install the Solaris 8 Software 1 of 2 CD, a custom JumpStart installation does not prompt you to install the Solaris 8 Software 2 of 2 CD.
Workaround: Choose one of the following workarounds.
If you are installing only the End User software group, you do not need to install the Solaris 8 Software 2 of 2 CD because the End User software and its basic locale support are on the Solaris 8 Software 1 of 2 CD.
If you are installing the Entire Distribution plus OEM, Entire Distribution, or Developer software, and are using a custom JumpStart installation from a server, use a network install server that contains the Solaris 8 1 of 2, 2 of 2, and Languages CDs. See “Creating a Profile Server” in Solaris 8 Advanced Installation Guide.
If you are installing the Entire Distribution plus OEM, Entire Distribution, or Developer software and are using a custom JumpStart installation from a diskette, follow these steps to install the Solaris 8 Software 2 of 2 and Languages CDs:
After the custom JumpStart completes the installation of the Solaris 8 Software 1 of 2 CD, reboot the system.
Log in to the system.
Insert the Solaris 8 Software 2 of 2 CD.
Execute the installer script and follow the instructions on the screen to install the remaining software.
Insert the Solaris 8 Languages CD.
Execute the installer script and follow the instructions on the screen to install any languages.
If you boot from a Solstice DiskSuiteTM or a SolarisTM Volume Manager mirrored root, or a Veritas encapsulated root, the lucreate command might be unable to determine the boot device. The following error message is displayed.
WARNING: Unable to determine root device by accessing boot device settings directly. ERROR: Unable to determine root device for current BE. ERROR: Unable to determine the physical boot device for the current BE <...>. Use the <-C> command line option to specify the physical boot device for the current BE <...> |
If you use lucreate -C to specify the physical boot device the command fails.
Workaround: Manually edit /usr/sbin/lucreate to enable Live Upgrade to determine the boot device from a Solstice DiskSuite or a Solaris Volume Manager mirrored root, or a Veritas encapsulated root. Follow these steps.
Make a backup copy of /usr/sbin/lucreate.
Open /usr/sbin/lucreate in a text editor.
Locate the following line in /usr/sbin/lucreate.
elif [ "${dpbe_pbeBootDev}" -eq "-" ] ; then |
Change the previous line to the following.
elif [ "${dpbe_pbeBootDev}" = '-' ] ; then |
Locate the following line in /usr/sbin/lucreate.
if [ "${OPTARG}" -ne "-" ] ; then |
Change the previous line to the following.
if [ "${OPTARG}" != '-' ] ; then |
Save the changes to /usr/sbin/lucreate.
The lucreate command can now determine the boot device and the -C option will function correctly.
You can remove the backup copy of /usr/sbin/lucreate when the upgrade completes.
If the /export directory is near full capacity and you upgrade to the Solaris 8 2/04 operating environment, the space requirements for /export are miscalculated and the upgrade fails. The problem commonly occurs if a diskless client is installed, or if third-party software is installed in /export. The following message is displayed.
WARNING: Insufficient space for the upgrade. |
Workaround: Before you upgrade, choose one of the following workarounds.
Temporarily rename the /export directory until the upgrade completes.
Temporarily comment out the /export line in the /etc/vfstab file until the upgrade completes.
If /export is a separate file system, then unmount /export before you perform the upgrade.
After upgrading from the Solaris 2.5.1 8/97 or 11/97 operating environment to the Solaris 8 operating environment, you might see the following error in /a/var/sadm/system/logs/upgrade_log.
rm: Unable to remove directory /a/var/sadm/pkg/.save.SUNWcsr: File exists |
Workaround: To prevent the error, before you upgrade to the Solaris 8 operating environment, perform fsck on the root file system.
To resolve the error after you upgrade, perform fsck on the root file system.
If your system currently supports diskless clients that were installed with the AdminSuite 2.3 Diskless Client tool, you must first delete all existing diskless clients prior to installing the Solaris 8 2/04 operating environment. For specific instructions, see “How to Set Up Your Diskless Client Environment” in Solaris 8 System Administration Supplement.
If you attempt to install the Solaris 8 2/04 operating environment over existing diskless clients, the following error message appears.
The Solaris Version (Solaris 7) on slice <xxxxxxxx> cannot be upgraded. There is an unknown problem with the software configuration installed on this disk. |
If you are upgrading from the Solaris 8 (Solaris WBEM Services 2.0), Solaris 8 6/00 (WBEM Services 2.1), Solaris 8 10/00 (WBEM Services 2.2), or Solaris 8 1/01 (WBEM Services 2.3) operating environments to the Solaris 8 2/04 operating environment (Solaris WBEM Services 2.4), you must convert any proprietary custom Managed Object Format (MOF) data to the new Reliable Log repository format that is used with Solaris WBEM Services 2.4. Failure to convert the data results in data loss.
Workaround: To convert WBEM data, before upgrading you must save the JavaSpacesTM software. After upgrading, you must run the wbemconfig convert command.
Before upgrading to the Solaris 8 2/04 operating environment, follow these steps to save the JavaSpaces software.
Become superuser.
Save the JavaSpaces software.
cp /usr/sadm/lib/wbem/outrigger.jar /usr/sadm/lib/wbem/outrigger.jar.tmp |
Check and record the version of the JDKTM software that is installed on your machine. For example:
# /usr/bin/java -version java version "1.2.1" Solaris VM (build Solaris_JDK_1.2.1_04c, native threads, sunwjit) |
You must be running the same version of the JDK software that was running when the original JavaSpaces datastore was created.
After upgrading to the Solaris 8 2/04 operating environment, you must convert the WBEM data. For specific instructions, see “Upgrading the CIM Object Manager Repository” in Solaris WBEM Services Administrator's Guide.
This problem affects systems that run the Solaris 2.5.1 and the Solaris 2.5.1 unbundled CDE operating environments. However, these systems are only affected if the unbundled CDE has been relocated to a directory other than /usr/dt. The CDE relocation on these systems has been accomplished by creating a symbolic link in /usr/dt that points to the relocated CDE.
When you upgrade to the Solaris 8 operating environment, CDE is reinstalled in /usr/dt, and the link to the relocated version is removed. The relocated CDE is not removed and is therefore orphaned.
If the upgrade involves the reallocation of file systems, the upgrade might fail because the reallocation mechanism does not allow for the extra space that is needed in /usr/dt for the new version of CDE. This failure is not visible until the upgrade has been completed. If this failure occurs, the upgrade log includes several messages that indicate more space is needed for an upgrade.
Workaround: Uninstall the relocated CDE before you start upgrading to the Solaris 8 operating environment. You can uninstall by using the install-cde script from the Solaris 2.5.1 CDE CD. You should run this script with the -uninstall flag to remove CDE.
If you installed WBEM 1.0 from the Solaris Easy Access Server (SEAS) 3.0 CD on a system that runs the Solaris 7 operating environment, you must remove the WBEM 1.0 packages before upgrading to the Solaris 8 operating environment. The Solaris WBEM Services 2.0 do not start after you upgrade the Solaris 7 operating environment with WBEM 1.0 to the Solaris 8 operating environment. The Common Information Model (CIM) Object Manager fails to start. The following error message is displayed.
File not found: /opt/sadm/lib/wbem/cimom.jar |
Workaround: Use the pkgrm command to remove the WBEM 1.0 packages before upgrading to the Solaris 8 operating environment.
Use the pkginfo command to check if the WBEM 1.0 packages are installed by typing the following.:
% pkginfo | grep WBEM |
Become superuser.
Use the pkgrm command to remove all WBEM 1.0 packages by typing the following.
# pkgrm SUNWwbapi # pkgrm SUNWwbcor # pkgrm SUNWwbdev # pkgrm SUNWwbdoc # pkgrm SUNWwbm |
The upgrade log might state that the SUNWeeudt package was only partially installed.
Doing pkgadd of SUNWeeudt to /. ERROR: attribute verification of </a/usr/dt/appconfig/types/ru_RU.KOI8-R/datatypes.dt> failed pathname does not exist ... Installation of <SUNWeeudt> partially failed. pkgadd return code = 2 |
Workaround: Perform the following steps after the upgrade has been completed.
To remove the SUNWeeudt package, type the following.
# pkgrm SUNWeeudt |
To add the SUNWeeudtpackage, type the following.
# pkgadd SUNWeeudt |
When you upgrade to the Solaris 8 2/04 operating environment from the Solaris 2.6 or Solaris 7 operating environment and do not select 64-bit support as an upgrade option, the following 64-bit packages are unnecessarily installed:
SUNWceuox
SUNWeeoux
SUNWneoux
SUNWseoux
SUNWweoux
Workaround: After you complete the upgrade, remove these 64-bit packages by using the pkgrm command:
# pkgrm SUNWceuox SUNWeeuox SUNWneuox SUNWseuox SUNWweuox |
If your system is already running 64-bit ready firmware, then the flash PROM update is not required.
If you want to run the 64-bit Solaris operating environment on an UltraSPARCTM system, you might need to update its flash PROM firmware. The Solaris 8 installation programs have an option for adding 64-bit support. This 64-bit support is selected by default when you install on Sun UltraSPARC systems. A 64-bit system only boots in the 64-bit mode by default if it has a CPU speed of 200 MHz or greater.
If you choose to run the 32-bit Solaris operating environment on any SunTM or UltraSPARC system, the flash PROM update is not needed.
The following table lists the UltraSPARC (sun4u) systems that are affected and the minimum firmware versions that are needed. System type is the equivalent of the output of the uname -i command. You can tell which firmware version you are running by using the prtconf -V command.
Table 1–2 Minimum Firmware Versions Required to Run 64–Bit Solaris Operating Environment on UltraSPARC Systems
System Type From uname -i |
Minimum Firmware Version From prtconf -V |
---|---|
SUNW,Ultra-1-Engine |
3.10.0 |
SUNW,Ultra-1 |
3.11.1 |
SUNW,Ultra-2 |
3.11.2 |
SUNW,Ultra-4 |
3.7.107 |
SUNW,Ultra-Enterprise |
3.2.16 |
If a system is not listed in the previous table, it does not need a flash PROM update.
For instructions on performing the flash PROM update by using the Solaris CD, refer to the Solaris 8 on Sun Hardware Collection. If you do not have this manual, you can obtain it at http://docs.sun.com.
The 200 field limitation of the awk and nawk utilities might cause installations of additional software to fail. This problem occurs under the following circumstances.
You install Veritas Volume Manager (VxVm) on a system running the Solaris 8 2/02 operating environment and Sun EnterpriseTM Alternate Pathing
You install Sun StorEdgeTM Component Manager software on a system running the Solaris 8 2/02 operating environment
A message similar to the following text displays.
Installing VxVM for Solaris 8 awk: record `Patch: 108528-13 Obs...' has too many fields record number 12 Alternate Pathing (AP) version 2.3.1 has been detected. This version of VxVM requires the following patch(es) to co-existwith AP 2.3.1: 110722 Install the above patch(es) before you continue the VxVM installation. This installation will now be aborted. pkgadd: ERROR: request script did not complete successfully Installation of <VRTSvxvm> failed. No changes were made to the system. |
Workaround: Contact your support channels to obtain the Solaris patch that increases the awk and nawk field limitation.
If you use the Solaris 8 2/02 Installation CD to install in a European locale, the Kiosk menu that appears at the end of the installation process displays in the C locale.
After upgrading from the Solaris 7 3/99, 5/99, 8/99, or 11/99 operating environment to the Solaris 8 2/04 operating environment, the following errors might appear in the upgrade logs.
Doing pkgadd of SUNWplow to /. pkgadd: ERROR: unable to create package object </a/usr/openwin/share/locale/de.ISO8859-15>. file type <s> expected <d> actual unable to remove existing directory at </a/usr/openwin/share/locale/de.ISO8859-15> .... Installation of <SUNWplow> partially failed. pkgadd return code = 2 Doing pkgadd of SUNWpldte to /. WARNING: /a/usr/dt/appconfig/types/de.ISO8859-15 may not overwrite a populated directory. ...... pkgadd: ERROR: /a/usr/dt/appconfig/types/de.ISO8859-15 could not be installed. ....... Installation of <SUNWpldte> partially failed. pkgadd return code = 2 |
This warning occurs because the patch switches the affected directories in the upgrade logs from symbolic links to directories. The upgrade process then attempts to install an updated version of the package that does not include the change. These errors do not affect the operating environment on your system.
Workaround: Ignore these error messages.