The Peripheral Component Interconnect (PCI) bus is a little endian bus. PCI devices are self-identifying — that is to say the PCI device provides configuration parameters to the system which allows the system to identify the device and its driver. The configuration parameters are represented in the form of name-value pairs that can be retrieved using the DDI property interfaces. See ddi_prop_lookup(9F) for details.
The PCI bus properties are derived from PCI Configuration Space, or supplied by the Fcode PROM if it exists. Therefore, driver configuration files are not necessary for these devices.
However, on some occasions, drivers for PCI devices may use driver configuration files to provide driver private properties. This can be done through global property mechanism. See driver.conf(4) for further details. Driver configuration files can also be used to augment or override properties for a specific instance of a driver.
All bus drivers of class pci recognize the following properties:
An arbitrary length array where each element of the array consists of a 5-tuple of 32-bit values. Each array element describes a logically contiguous mappable resource on the PCI bus.
The first 3 values in the 5-tuple describe the PCI address of the mappable resource. The first tuple contains the following information:
|Bits 0 - 7||8-bit Register number|
|Bits 8 - 10||3-bit Function number|
|Bits 11 - 15||5-bit Device number|
|Bits 16 - 23||8-bit Bus number|
|Bits 24 - 25||2-bit Address Space type identifier|
The Address Space type identifier may be interpreted as follows:
|0x2||32-bit Memory Space address|
|0x3||64-bit Memory Space address|
The Bus number is a unique identifying number assigned to each PCI bus within a PCI domain.
The Device number is a unique identifying number assigned to each PCI device on a PCI bus. Note that a Device number is only unique within the set of Device numbers for a particular bus.
Each PCI device can have 1 to 8 logically independent functions, each with its own independent set of configuration registers. Each function on a device is assigned a Function number. For a PCI device with only one function, the Function number must be 0.
The Register number field selects a particular register within the set of configuration registers corresponding to the selected function.
The second and third values in the reg property 5-tuple specify the 64-bit address of the mappable resource within the PCI address domain. The second 32-bit tuple corresponds to the high order 4 bytes of the 64-bit address. The third 32-bit tuple corresponds to the low order bytes.
The fourth and fifth 32-bit values in the 5-tuple reg property specify the size of the mappable resource. The size is a 64-bit value where the fourth tuple corresponds to the high order bytes of the 64-bit size and the fifth corresponds to the low order.
The driver can refer to the elements of this array by index, and construct kernel mappings to these addresses using ddi_regs_map_setup(9F). The index into the array is passed as the rnumber argument of ddi_regs_map_setup(9F).
At a high-level interrupt context, you can use the ddi_get* and ddi_put* family of functions to access I/O and memory space. However, access to configuration space is not allowed when running at a high-interrupt level.
This property consists of a single integer element array. Valid interrupt property values are 1, 2, 3, and 4. This value is derived directly from the contents of the device's Configuration Interrupt Pin register.
A driver should use an index value of 0 when registering its interrupt handler with ddi_add_intr(9F).
All PCI devices support the reg property. The Device number and Function number as derived from the reg property are used to construct the address part of the device name under /devices.
Only devices that generate interrupts support an interrupts property.
Occasionally it may be necessary to override or augment the configuration information supplied by a PCI device. This can be achieved by writing a driver configuration file that describes a prototype device node specification containing the additional properties required.
For the system to merge the prototype node specification into an actual device node, certain conditions must be met. First, the name property must be identical. Second, the parent property must identify the PCI bus. Third, the unit-address property must identify the card. The format of the unit-address property is
where DD is the device number and F is the function number. If the function number is 0, only DD is specified.
An example configuration file called ACME,scsi-hba.conf for a PCI driver called ACME,scsi-hba follows:
# # Copyright (c) 1995, ACME SCSI Host Bus Adaptor # ident "@(#)ACME,scsi-hba.conf 1.1 96/02/04" name="ACME,scsi-hba" parent="/pci@1,0/pci@1f,4000" unit-address="3" scsi-initiator-id=6; hba-advanced-mode="on"; hba-dma-speed=10;
In this example, we provide a property scsi-initiator-id to specify the SCSI bus initiator id that the adapter should use, for just one particular instance of adapter installed in the machine. We use the name property to identify the driver and the parent property to identify the particular bus the card is plugged into. This example uses the parent's full path name to identify the bus. The unit-address property identifies the card itself, with device number of 3 and function number of 0.
Two global driver properties are also created: hba-advanced-mode (which has the string value on) and hba-dma-speed (which has the value 10 M bit/s). These properties apply to all device nodes of the ACME,scsi-hba. The following is an example configuration file called ACME,foo.conf for a PCI driver called ACME,foo;
# # Copyright (c) 1996, ACME Foo driver # ident "@(#)ACME,foo.conf 1.1 95/11/14" name="ACME,foo" class="pci" unit-address="3,1" debug-mode=12;
In this example, we provide a property debug-mode for all instances of the ACME,foo driver with parents of class pci and device and function numbers of 3 and 1, respectively.
See attributes(5) for descriptions of the following attributes:
|ATTRIBUTE TYPE||ATTRIBUTE VALUE|
IEEE 1275 PCI Bus Binding