|
|
|
|
|
apit.unattended |
Tells SIA to run in unattended mode. Values supported: true | false Example:
apit.unattended=true |
X |
X |
X |
apit.welcome.acceptlicense |
Accepts the SIA license agreement. Values supported: true | falseExample: apit.welcome.acceptlicense=true |
X |
X |
X |
apit.remoteUpdate |
Tells SIA
to look for SIA software updates. You should always perform an update to
ensure you install the latest software and firmware. Values supported: true | falseExample:
apit.remoteUpdate=true |
X |
X |
X |
apit.remoteUpdateURL |
If you specified “true” for remoteUpdate, tells SIA where to look for SIA
software updates. Values supported: Any URL with updated SIA content files. You only
need to specify this variable if you are not using the default url. Default
url: http://sia-updates.sun.com/remoteUpdate |
X (if remote Update is true and default url is not
used) |
X (if remote Update is true and default url is not used) |
X
(if remote Update is true and default url is not used) |
apit.networking |
Tells SIA
it has permission to work over the network. If true, SIA will configure
network settings based on networkconfig variables. Values supported: true | falseExample: apit.networking=true |
X |
X |
X |
apit.networkconfig.needNetwork |
If you
specified “true” for network, tells SIA whether network access is required for a
particular task. Values supported: true | falseExample: apit.networkconfig.needNetwork=true |
X (if networking is true) |
X
(if networking is true) |
X (if networking is true) |
apit.networkconfig.activeNic |
If you specified “true” for
network, tells SIA which network interface is connected to the active network. Values
supported: eth0 | eth1 | eth2 | eth3 ... etc. Example: apit.networkconfig.activeNic=eth0 |
X (if networking
is true) |
X (if networking is true) |
X (if networking is true) |
apit.networkconfig.NetworkType |
If you specified
“true” for network, tells SIA the configuration of the active network interface. Values
supported: static | dhcpExample: apit.networkconfig.NetworkType=dhcp |
X (if networking is true) |
X (if networking is
true) |
X (if networking is true) |
apit.networkconfig.useDHCP |
If you selected “dhcp” as the NetworkType, tells
SIA to obtain the server’s address from the DHCP server. Values supported: true
| false Example: apit.networkconfig.useDHCP=true |
X (if networking is true) |
X (if networking is true) |
X (if
networking is true) |
apit.networkconfig.ipfield |
If you selected “static” as the NetworkType, tells SIA to use
the server’s IP address value you provide. Example: apit.networkconfig.ipfield=n.n.n.n |
X (if static IP is
used) |
X (if static IP is used) |
X (if static IP is used) |
apit.networkconfig.gatewayField |
If you
selected “static” as the NetworkType, tells SIA to use the IP address value
you provide. Example: apit.networkconfig.gatewayfield=n.n.n.n |
X (if static IP is used) |
X (if static IP is
used) |
X (if static IP is used) |
apit.networkconfig.netmaskedField |
If you selected “static” as the NetworkType,
tells SIA to use the IP address value you provide. Example: apit.networkconfig.ipfield=n.n.n.n |
X (if static
IP is used) |
X (if static IP is used) |
X (if static IP is
used) |
apit.http_proxy |
If, for example, you specified “true” for remoteUpdate, tells SIA to use a
proxy server for internet access. Examples: apit.http_proxy=n.n.n.n (IP address) apit.http_proxy=file://web-proxy-configfile apit.http_proxy=http://web-proxy-server apit.http_proxy=http://internal-host:portnumber |
X (if proxy used) |
X (if proxy
used) |
X (if proxy used) |
apit.taskList.selectedTask |
Tells SIA which task to perform (only one task
can be run per unattended session). This variable is required in the state
file. Values supported: SP/Bios Firmware Upgrade | Operating System Installation | HBA Firmware
Upgrade | Expander Firmware Upgrade | SP Recovery Example: apit.taskList.selectedTask=Operating System Installation |
X |
X |
X |
apit.osid.installLoc |
Tells SIA where
the network image of the Linux operating system to be installed is located.
The path is to the directory containing the image (ISO or extracted ISO),
not the image itself. The directory cannot contain more than one image. Example: apit.osid.installLoc=http://path_to_imagedirectory |
|
X |
|
apit.osid.installMedia |
Tells
SIA where the CD or .iso file for the OS installation software is
located. Values supported: cdrom | networkLinux | networkWindows Example: apit.osid.installMedia=cdrom |
X |
X |
|
apit.osid.installMethod |
Tells SIA which file transfer
protocol to use during the installation. Values supported: http | ftp | nfs Example:
apit.osid.installMethod=http |
X |
X |
|
apit.osid.kickstart |
Tells SIA where the kickstart file is located for a Linux installation. This
could be the URL to the Red Hat kickstart file or the
SUSE autoyast file. Examples: apit.osid.kickstart=http://url_to_kickstart apit.osid.kickstart=ftp://url_to_kickstart apit.osid.kickstart=nfs://url_to_kickstart |
|
X |
|
apit.windows2008.imageName |
Specifies the version of Windows Server 2008 to be installed.
Values determine whether this is a full or core–only Windows installation. Core installations allow
you to install Windows with only the components needed to run a small
set of core network roles. Supported values:
WINDOWS LONGHORN [R2] SERVERSTANDARD
WINDOWS LONGHORN [R2] SERVERENTERPRISE
WINDOWS LONGHORN [R2] SERVERDATACENTER
WINDOWS LONGHORN R2 SERVERWEB
WINDOWS LONGHORN [R2] SERVERSTANDARDCORE
WINDOWS LONGHORN [R2] SERVERENTERPRISECORE
WINDOWS LONGHORN [R2] SERVERDATACENTERCORE
WINDOWS LONGHORN R2 SERVERWEBCORE
Note: The R2 value is only
required for Windows Server 2008 R2. Windows Server 2008 SERVERWEB/CORE is only supported
with R2. Example for pre-R2: apit.windows2008.imageName=WINDOWS LOGHORN SERVERENTERPRISE Example for R2: apit.windows2008.imageName=WINDOWS LONGHORN R2 SERVERENTERPRISE |
X (2008
only) |
|
|
apit.osid.windows.iso.url1 |
Based on the installMethod you chose (http, ftp or nfs), tells SIA
where the location of the first Windows OS install disk .iso image file is
located. Examples: apit.osid.windows.iso.url1=http://path_to_disk1.iso apit.osid.windows.iso.url1=ftp://path_to_disk1.iso apit.osid.windows.iso.url1=nfs://path_to_disk1.iso |
X |
|
|
apit.osid.windows.iso.url2 |
Based on the installMethod you chose (http, ftp or nfs), tells SIA
where the location of the second Windows OS install disk .iso image file is
located (if on two disks). Examples: apit.osid.windows.iso.url2=http://path_to_disk2.iso apit.osid.windows.iso.url2=ftp://path_to_disk2.iso apit.osid.windows.iso.url2=nfs://path_to_disk2.iso |
X |
|
|
apit.enclosureID.oldEnclosureID |
Used as part of a two-step process that
allows you to replace a Sun Blade 6000 disk module. The value for
this variable must be the old enclosure ID number (also called WWN) that
can be found on the circuit board of the blade being replaced. |
|
|
|
apit.enclosureID.newEnclosureID |
Used as
part of a two-step process that allows you to replace a Sun Blade
6000 disk module. This value for this variable must be the new
enclosure ID number (also called WWN) that can be found on the circuit
board of the replacement blade. |
|
|
|
apit.firmware.enabled |
Tells SIA to enable or disable its firmware update
function. Values supported: true | false Typically used in a test environment, this variable
is not required to upgrade firmware. |
|
|
|
apit.firmware.spIP |
Part of a firmware upgrade task. Tells SIA
the IP address of the server’s service processor. Example: apit.firmware.spIP=n.n.n.n |
|
|
X |
apit.firmware.spPasswd |
Part of a firmware upgrade
task. Tells SIA the password of the server’s service processor. Example: apit.firmware.spIP=changeme |
|
|
X |
apit.windows.acceptEula |
Tells SIA to
accept the EULA (End User License Agreement), as required when installing the Windows
OS. Example: apit.windows.acceptEula |
X (2003 only) |
|
|
apit.windows.adminPasswd |
Tells SIA the password you wish to use for
the administrator account set up during the installation of the Windows OS. Password
must comply with Windows password standards. Example: apit.windows.adminPasswd=myadminpassword |
X (2003 only) |
|
|
apit.windows.computerName |
Tells SIA the computer name
you wish to use for the server set up during the installation of
the Windows OS. Example: apit.windows.computerName=mycomputername |
X (2003 only) |
|
|
apit.windows.key |
Tells SIA the product key for your
retail copy of the Windows OS. Required during Windows installation. Example: apit.windows.key=XXXXX-XXXXX-XXXXX-XXXXX-XXXXX |
X (2003 only) |
|
|
apit.windows.orgName |
Tells
SIA the organization name you wish to use for the server set
up during the installation of the Windows OS. Example: apit.windows.orgName=myorganization |
X (2003 only) |
|
|
apit.windows.userName |
Tells SIA the
user name you wish to use for the initial user account set up
during the installation of the Windows OS. Example: apit.windows.userName=myusername |
X (2003 only) |
|
|
apit.done.notifyUrl |
Tells SIA to
access the specified URL following the completion of enabled SIA tasks. This is
currently only supported for Sun N1 System Manager. Example: apit.done.notifyUrl=http://my_destination_url |
|
|
|