BusLogic BT-946C, BT-956C HBAs

Preconfiguration Information

If your BT-946C PCI card is labeled Rev. A or B, it needs to be supported in ISA emulation mode; use I/O address 0x334.

Note -
To find the revision level of a BusLogic PCI card, look at the card itself. The revision of the card is not provided in the manufacturer's documentation.

If your BT-946C is labeled Rev. C, it can be supported in native PCI mode. To do this, select "Advanced option," and choose "NO" for the "Host Adapter I/O Port Address as default" option.

If your PCI card is model BT-956C or model BT-946C Rev. E, it can also be supported in native PCI mode. To do this, disable the "Set ISA Compatible I/O Port (PCI Only)" option.
Since your BusLogic board model ends in "C", you must enter the AutoSCSI configuration utility and check the termination.

o IRQ Level:	5, 6, 7, 8, 9, 10, 11, 12, 14, 15
o I/O Address:	0x334, 0x230, 0x234, 0x130, 0x134

Note -

I/O addresses are dynamically configured for BT-946C Rev. C PCI adapters.

Using an I/O address of 0x330 causes the Solaris aha driver to be selected instead of blogic native mode drivers. These cards have not been tested in Adaptec AHA-1540 mode.
Do not run the drvconfig utility during heavy I/O involving disks and tapes because doing so can cause data overrun errors.
Data overrun errors may occur under high stress when your system is configured with multiple disks.
If problems occur during Solaris installation, set the Interrupt Pin number of the "configure Adapter" option in the BusLogic AutoSCSI utility as follows:

Slot

Interrupt Pin

0

A

1

B

2

C

For more information, see the sections "Configuration for Non-Conforming PCI Motherboards" and "Handling Motherboard Variations" in the documentation that comes with your PCI BusLogic board.
Early versions of Rev. A, B, and C of the BT-946C may not work with the Solaris operating environment.

Upgrade to at least Firmware 4.25J, BIOS 4.92E, and AutoSCSI 1.06E, if you have BT946C Rev. B. Upgrade the controller to at least BT946C Rev. E.

Insert the board into the bus master slot, and using the AutoSCSI utility:

Set the "Adapter BIOS Supports Space > 1 GB (DOS) only" option to Yes if the boot disk is larger than 1 Gbyte.
Put the adapter in ISA-compatible mode by setting the value for "Set Host Bus Adapter I/O Port Address as Default" to No.
Ensure the Advanced option "BIOS Support for > 2 Drives (DOS 5.0 or above)" is set to No.
Configure the IRQ and BIOS address values manually if your PCI motherboard is not fully PCI-specification compliant. If the system hangs while installing the Solaris software, do the following:
- Check the IRQ jumpers on the motherboard, if any.
- Run the CMOS utility to set the IRQ and BIOS addresses, if any.
- Run the BusLogic AutoSCSI utility.
All the settings should match each other. If you need to manually configure the BIOS address, you may have to check jumpers JP4 and JP5.

Insert the board into the bus master slot, and using the AutoSCSI utility:

Set the "Adapter BIOS Supports Space > 1 GB (DOS only)" option to Yes if the boot disk is larger than 1 Gbyte.
Choose the defaults, except set the 5.1 "BIOS Support for > 2 Drives (DOS 5.0 or above)" to No.

Follow these guidelines when adding a second BusLogic PCI controller to a system.

The already installed PCI board must be the primary controller.
The primary controller must have an I/O address that precedes the secondary controller in "Supported Settings" (as listed from left to right). For example, the primary controller can use an I/O address of 0x234, as long as the secondary controller uses either 0x130 or 0x134. The I/O address of each board is determined by its slot. Try different slots until the first card works as the primary controller.
Disable the BIOS on the secondary controller.
Wide-mode PCI adapters will support targets greater than 7 if the proper entries are added to the system configuration files: /kernel/drv/sd (for disk), and /kernel/drv/st.conf (for tape).