This section contains the procedures you need to configure Sun Cluster HA for Samba.
Some procedures within this section require you to use certain Sun Cluster commands. Refer to the relevant Sun Cluster command man page for more information about these command and their parameters.
Determine if a single or multiple Samba instances will be deployed.
Refer to Restriction for multiple Samba instances that require winbind to determine how to deploy a single or multiple Samba instances with or without winbind.
Once you have determined how Samba will be deployed, you can chose one or more of the steps below.
Create a failover resource group for Samba.
Use How to Register and Configure Sun Cluster HA for Samba in a failover resource group for Example 3 and Example 4.
Create a scalable resource group for winbind.
Use How to Register and Configure Sun Cluster HA for Samba in a failover resource group with winbind in a scalable resource group for Example 5.
Create a failover resource group for an HA container for Samba.
Use How to Register and Configure Sun Cluster HA for Samba in an HA Container for Example 6.
This procedure assumes that you installed the data service packages during your initial Sun Cluster installation.
If you did not install the Sun Cluster HA for Samba packages as part of your initial Sun Cluster installation, go to How to Install the Sun Cluster HA for Samba Packages.
Perform this procedure on one node of the cluster only.
On a cluster member, become superuser or assume a role that provides solaris.cluster.modify RBAC authorization.
Register the following resource types.
# clresourcetype register SUNW.HAStoragePlus # clresourcetype register SUNW.gds |
Create a failover resource group for Samba.
Refer to Restriction for multiple Samba instances that require winbind for more information on the nodelist entry.
# clresourcegroup create -n nodelist samba-resource-group |
Create a resource for the Samba Logical Hostname.
# clreslogicalhostname create -g samba-resource-group \ > -h samba-logical-hostname \ > samba-logical-hostname-resource |
Create a resource for the Samba Disk Storage.
If a ZFS highly available local file system is being used
# clresource create -g samba-resource-group \ > -t SUNW.HAStoragePlus \ > -p Zpools=samba-zspool \ > samba-hastorage-resource |
If a cluster file system or any other non-ZFS highly available local file system is being used
# clresource create -g samba-resource-group \ > -t SUNW.HAStoragePlus \ > -p FilesystemMountPoints=samba-filesystem-mountpoint \ > samba-hastorage-resource |
Bring online the failover resource group for Samba that now includes the HA Storage and Logical Hostname resources.
# clresourcegroup online -M samba-resource-group |
If winbind is required, create and register a winbind resource.
If Samba was dynamically linked and is being used as an Active Directory Server member you must configure the LDPATH variable to point to the Samba lib directory.
Edit the samba_config file and follow the comments within that file. Ensure that SERVICES="winbindd" is specified. After you have edited samba_config, you must register the resource.
# cd /opt/SUNWscsmb/util # vi samba_config # ./samba_register |
The following deployment example has been taken from Deployment Example: Installing Samba from http://www.samba.org.
Vigor5# cat > /var/tmp/winbind_config <<-EOF #+++ Resource Specific Parameters +++ RS=winbind RG=samba-rg RS_LH=samba-lh RS_HAS=sambaZFS-has SERVICES="winbindd" #+++ Common Parameters +++ BINDIR=/opt/samba/bin SBINDIR=/opt/samba/sbin CFGDIR=/local/samba/smb1 LDPATH=/opt/samba/lib FMUSER=homer #+++ SMBD & NMBD Specific Parameters (See Note 1) +++ SAMBA_LOGDIR= SAMBA_FMPASS= SAMBA_FMDOMAIN= #+++ WINBIND Specific Parameters (See Note 2) +++ WINBIND_DISCACHE=FALSE WINBIND_SINGLEMODE=FALSE #+++ Zone Specific Parameters (See Note 3) +++ RS_ZONE= LHOST= PROJECT=default TIMEOUT=30 EOF |
Vigor5# /opt/SUNWscsmb/util/samba_register -f /var/tmp/winbind_config |
If winbind is required enable the resource.
# clresource enable winbind-resource |
Create and register a Samba resource.
If Samba was dynamically linked and is being used as an Active Directory Server member you must configure the LDPATH variable to point to the Samba lib directory.
Edit the samba_config file and follow the comments within that file. Ensure that SERVICES="smbd" or SERVICES="smbd,nmbd" is specified. After you have edited samba_config, you must register the resource.
# cd /opt/SUNWscsmb/util # vi samba_config # ./samba_register |
The following deployment example has been taken from Deployment Example: Installing Samba from http://www.samba.org.
Vigor5# cat > /var/tmp/samba_config <<-EOF #+++ Resource Specific Parameters +++ RS=samba RG=samba-rg RS_LH=samba-lh RS_HAS=sambaZFS-has SERVICES="smbd" #+++ Common Parameters +++ BINDIR=/opt/samba/bin SBINDIR=/opt/samba/sbin CFGDIR=/local/samba/smb1 LDPATH=/opt/samba/lib FMUSER=homer #+++ SMBD & NMBD Specific Parameters (See Note 1) +++ SAMBA_LOGDIR=/local/samba/smb1/logs SAMBA_FMPASS=smb4#ads SAMBA_FMDOMAIN= #+++ WINBIND Specific Parameters (See Note 2) +++ WINBIND_DISCACHE= WINBIND_SINGLEMODE= #+++ Zone Specific Parameters (See Note 3) +++ RS_ZONE= LHOST= PROJECT=default TIMEOUT=30 EOF |
Vigor5# /opt/SUNWscsmb/util/samba_register -f /var/tmp/samba_config |
If winbind is used, ensure Samba is dependent on winbind.
# clresource set -p Resource_dependencies=winbind-resource{local_node} samba-resource |
Enable the Samba resource.
# clresource enable samba-resource |
See Verifying the Sun Cluster HA for Samba Installation and Configuration
This procedure assumes that you installed the data service packages during your initial Sun Cluster installation.
If you did not install the Sun Cluster HA for Samba packages as part of your initial Sun Cluster installation, go to How to Install the Sun Cluster HA for Samba Packages.
Perform this procedure on one node of the cluster only.
On a cluster member, become superuser or assume a role that provides solaris.cluster.modify RBAC authorization.
Register the following resource types.
# clresourcetype register SUNW.HAStoragePlus # clresourcetype register SUNW.gds |
Create a failover resource group for the winbind shared network address.
Refer to Restriction for multiple Samba instances that require winbind for more information on the nodelist entry.
# clresourcegroup create -n nodelist winbind-failover-resource-group |
Create a resource for the winbind Logical Hostname.
# clressharedaddress create -g winbind-failover-resource-group \ > -h winbind-logical-hostname \ > winbind-logical-hostname-resource |
Create a scalable resource group for the scalable winbind resource.
Refer to Restriction for multiple Samba instances that require winbind for more information on the nodelist entry.
# clresourcegroup create -n nodelist -S \ > -p Maximum_primaries=maximum-number-active-primaries \ > -p Desired_primaries=desired-number-active-primaries \ > winbind-scalable-resource-group |
Create a resource for the winbind Disk Storage.
For a scalable HA Storage resource you must use a cluster file system.
# clresource create -g winbind-scalable-resource-group \ > -t SUNW.HAStoragePlus \ > -p FilesystemMountPoints=winbind-filesystem-mount-point \ > -x AffinityOn=FALSE \ > winbind-ha-storage-resource |
Enable the failover and scalable resource groups for winbind that now includes the HA Storage and Logical Hostname resources.
# clresourcegroup online -M winbind-failover-resource-group # clresourcegroup online -M winbind-scalable-resource-group |
Create and register a winbind resource.
If Samba was dynamically linked and is being used as an Active Directory Server member you must configure the LDPATH variable to point to the Samba lib directory.
Edit the samba_config file and follow the comments within that file. Ensure that SERVICES="winbindd" is specified. After you have edited samba_config, you must register the resource.
# cd /opt/SUNWscsmb/util # vi samba_config # ./samba_register |
The following modified deployment example has been taken from Deployment Example: Installing Samba from http://www.samba.org, which shows a winbind-scalable-resource-group and winbind-ha-storage-resource. The winbind configuration directory is also located in a cluster file system, /global/samba/winbind.
Vigor5# cat > /var/tmp/winbind_config <<-EOF #+++ Resource Specific Parameters +++ RS=winbind RG=winbindS-rg RS_LH=winbind-lh RS_HAS=winbindS-has SERVICES="winbindd" #+++ Common Parameters +++ BINDIR=/opt/samba/bin SBINDIR=/opt/samba/sbin CFGDIR=/global/samba/winbind LDPATH=/opt/samba/lib FMUSER=homer #+++ SMBD & NMBD Specific Parameters (See Note 1) +++ SAMBA_LOGDIR= SAMBA_FMPASS= SAMBA_FMDOMAIN= #+++ WINBIND Specific Parameters (See Note 2) +++ WINBIND_DISCACHE=FALSE WINBIND_SINGLEMODE=FALSE #+++ Zone Specific Parameters (See Note 3) +++ RS_ZONE= LHOST= PROJECT=default TIMEOUT=30 EOF |
Vigor5# /opt/SUNWscsmb/util/samba_register -f /var/tmp/winbind_config |
Enable the winbind resource.
# clresource enable winbind-resource |
Create and register a Samba resource in a failover resource group.
Follow steps 3, 4, 5, 6, 9, 10 and 11 in How to Register and Configure Sun Cluster HA for Samba in a failover resource group.
See Verifying the Sun Cluster HA for Samba Installation and Configuration
This procedure assumes that you installed the data service packages during your initial Sun Cluster installation.
If you did not install the Sun Cluster HA for Samba packages as part of your initial Sun Cluster installation, go to How to Install the Sun Cluster HA for Samba Packages.
Perform this procedure on one node of the cluster only.
Create a failover resource group for Samba.
Follow steps 1, 2, 3, 4, 5 and 6 in How to Register and Configure Sun Cluster HA for Samba in a failover resource group.
Register the HA container in the failover resource group for Samba.
Refer to Sun Cluster Data Service for Solaris Containers Guide for Solaris OS for complete information about HA containers.
Edit the sczbt_config file and follow the comments within that file. Ensure that you specify the samba-resource-group for the RG= parameter within sczbt_config.
After you have edited sczbt_config, you must register the resource.
# cd /opt/SUNWsczone/sczbt/util # vi sczbt_config # ./sczbt_register |
The following deployment example has been taken from Deployment Example: Installing Samba in an HA Container.
Vigor5# cat > /var/tmp/sczbt_config <<-EOF RS=sambaFOZ RG=samba-rg PARAMETERDIR=/zones SC_NETWORK=true SC_LH=samba-lh FAILOVER=true HAS_RS=sambaSVM-has,sambaZFS-has Zonename=failover Zonebootopt= Milestone=multi-user-server Mounts=/local EOF Vigor5# Vigor5# /opt/SUNWsczone/sczbt/util/sczbt_register -f /var/tmp/sczbt_config |
Enable the HA container resource.
# clresource enable samba-failover-zone-resource |
If winbind is required, create and register a winbind resource.
If Samba was dynamically linked and is being used as an Active Directory Server member you must configure the LDPATH variable to point to the Samba lib directory.
Edit the samba_config file and follow the comments within that file. Ensure that SERVICES="winbindd" and the RS_ZONE variable specifies the Sun Cluster resource for the HA container. After you have edited samba_config, you must register the resource.
# cd /opt/SUNWscsmb/util # vi samba_config # ./samba_register |
If winbind is required, enable the winbind resource.
# clresource enable winbind-resource |
Create and register a Samba resource.
If Samba was dynamically linked and is being used as an Active Directory Server member you must configure the LDPATH variable to point to the Samba lib directory.
Edit the samba_config file and follow the comments within that file. Ensure that SERVICES="smbd" or SERVICES="smbd,nmbd" and the RS_ZONE variable specifies the Sun Cluster resource for the HA container. After you have edited samba_config, you must register the resource.
# cd /opt/SUNWscsmb/util # vi samba_config # ./samba_register |
The following deployment example has been taken from Deployment Example: Installing Samba in an HA Container.
Vigor5# cat > /var/tmp/samba_config <<-EOF #+++ Resource Specific Parameters +++ RS=samba RG=samba-rg RS_LH=samba-lh RS_HAS=sambaZFS-has SERVICES="smbd,nmbd" #+++ Common Parameters +++ BINDIR=/usr/sfw/bin SBINDIR=/usr/sfw/sbin CFGDIR=/local/samba/smb1 LDPATH=/usr/sfw/lib FMUSER=homer #+++ SMBD & NMBD Specific Parameters (See Note 1) +++ SAMBA_LOGDIR=/local/samba/smb1/logs SAMBA_FMPASS=samba SAMBA_FMDOMAIN= #+++ WINBIND Specific Parameters (See Note 2) +++ WINBIND_DISCACHE=FALSE WINBIND_SINGLEMODE=FALSE #+++ Zone Specific Parameters (See Note 3) +++ RS_ZONE=sambaFOZ LHOST=192.168.1.132 PROJECT=default TIMEOUT=30 EOF Vigor5# Vigor5# /opt/SUNWscsmb/util/samba_register -f /var/tmp/samba_config |
If winbind is used, ensure Samba is dependent on winbind.
# clresource set -p Resource_dependencies=winbind-resource{local_node} samba-resource |
Enable the Samba resource.
# clresource enable samba-resource |
See Verifying the Sun Cluster HA for Samba Installation and Configuration