sigfpe(3)

NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | FILES | ATTRIBUTES | SEE ALSO | DIAGNOSTICS

NAME

sigfpe- signal handling for specific SIGFPE codes

SYNOPSIS

#include <floatingpoint.h>
#include <siginfo.h>

sigfpe_handler_type sigfpe(sigfpe_code_type code, sigfpe_handler_type hdl);

DESCRIPTION

This function allows signal handling to be specified for particular SIGFPE codes. A call to sigfpe() defines a new handler hdl for a particular SIGFPE code and returns the old handler as the value of the function sigfpe(). Normally handlers are specified as pointers to functions; the special cases SIGFPE_IGNORE, SIGFPE_ABORT, and SIGFPE_DEFAULT allow ignoring, dumping core using abort(3C), or default handling respectively. Default handling is to dump core using abort(3C).

code is usually one of the five IEEE754-related SIGFPE codes:

---

FPE_FLTRES   fp_inexact - floating-point inexact result
FPE_FLTDIV   fp_division - floating-point division by zero        
FPE_FLTUND   fp_underflow - floating-point underflow
FPE_FLTOVF   fp_overflow - floating-point overflow
FPE_FLTINV   fp_invalid - floating-point invalid operation

---

Three steps are required to intercept an IEEE754-related SIGFPE code with sigfpe():

1. Set up a handler with sigfpe().

2. Enable the relevant IEEE754 trapping capability in the hardware, perhaps by using assembly-language instructions.

3. Perform a floating-point operation that generates the intended IEEE754 exception.

sigfpe() never changes floating-point hardware mode bits affecting IEEE754 trapping. No IEEE754-related SIGFPE signals will be generated unless those hardware mode bits are enabled.

SIGFPE signals can be handled using sigfpe(), sigaction(2) or signal(3C). In a particular program, to avoid confusion, use only one of these interfaces to handle SIGFPE signals.

EXAMPLES

---

Example 1 Example Of A User-Specified Signal Handler




A user-specified signal handler might look like this:

#include <floatingpoint.h>
#include <siginfo.h>
#include <ucontext.h>
/*
* The sample_handler prints out a message then commits suicide.
*/
void
sample_handler(int sig, siginfo_t *sip, ucontext_t *uap) {
	char *label;
        switch (sip->si_code) {
	case FPE_FLTINV: label = "invalid operand"; break;
	case FPE_FLTRES: label = "inexact"; break;
	case FPE_FLTDIV: label = "division-by-zero"; break;
	case FPE_FLTUND: label = "underflow"; break;
	case FPE_FLTOVF: label = "overflow"; break;
	default: label = "???"; break;
	}
	fprintf(stderr, "FP exception %s (0x%x) occurred at address %p.\n",
                        label, sip->si_code, (void *) sip->si_addr);
	abort();
}

and it might be set up like this:

#include <floatingpoint.h>
#include <siginfo.h>
#include <ucontext.h>
extern void sample_handler(int, siginfo_t *, ucontext_t *);
main(void) {
      sigfpe_handler_type hdl, old_handler1, old_handler2;
/*
 * save current fp_overflow and fp_invalid handlers; set the new
* fp_overflow handler to sample_handler() and set the new
* fp_invalid handler to SIGFPE_ABORT (abort on invalid)
*/
    hdl = (sigfpe_handler_type) sample_handler;
    old_handler1 = sigfpe(FPE_FLTOVF, hdl);
    old_handler2 = sigfpe(FPE_FLTINV, SIGFPE_ABORT);
    ...
/*
 * restore old fp_overflow and fp_invalid handlers
 */
     sigfpe(FPE_FLTOVF, old_handler1);
     sigfpe(FPE_FLTINV, old_handler2);
}

---

FILES

/usr/include/floatingpoint.h

/usr/include/siginfo.h

ATTRIBUTES

See attributes(5) for descriptions of the following attributes:

ATTRIBUTE TYPE	ATTRIBUTE VALUE
MT-Level	Safe

SEE ALSO

sigaction(2), abort(3C), signal(3C), attributes(5), floatingpoint(5)

DIAGNOSTICS

sigfpe() returns BADSIG if code is not zero or a defined SIGFPE code.

SunOS 5.7  Last Revised 29 Dec 1996

NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | FILES | ATTRIBUTES | SEE ALSO | DIAGNOSTICS