The Configuration section of the Option menu displays the serial ports available for the SPC/S board. The available ports are listed in the table below.
Table 33-1 spiftest Serial Ports for the SPC/S Board
Board Number |
Board Device |
Serial Ports |
Parallel Ports |
---|---|---|---|
0 |
stc0 |
term/0-7 |
printers/0 |
1 |
stc1 |
term/8-15 |
printers/1 |
2 |
stc2 |
term/16-23 |
printers/2 |
3 |
stc3 |
term/24-31 |
printers/3 |
4 |
stc4 |
term/32-39 |
printers/4 |
5 |
stc5 |
term/40-47 |
printers/5 |
6 |
stc6 |
term/48-55 |
printers/6 |
7 |
stc7 |
term/56-63 |
printers/7 |
The spiftest options are described in the table below.
Table 33-2 spiftest Options
spiftest Option |
Description |
---|---|
96-pin Loopback (LB) |
Provides data transmission, full-modem loopback, and parallel port loopback testing. You must attach a 96-pin loopback connector (part number 370-1366) to the card before running this test (see Appendix A, "96-Pin Female Lookback Connector" section).. |
Internal Test |
Performs a quick internal check of the serial parallel controller card(s) installed in SBus slots. You do not need to attach anything to the card(s) to perform this test. |
25-pin Loopback (LB) |
Provides full-duplex transmission and full-modem loopback testing of the serial port selected in the Serial Port selection of this menu. You must attach the 25-pin Loopback plug to the serial port on the Serial Parallel Controller Patch Panel that is being tested (See Appendix A). This test cannot be run concurrently with the Echo-TTY option enabled. |
Echo-TTY |
Checks the proper operation of the serial port selected in the Serial Port section of this menu by echoing characters typed on a TTY terminal keyboard to the TTY terminal screen. The characters you type should be displayed on the TTY screen. Note: TTY connection to the spif serial port requires corresponding character size setup. For example, if a TTY attachment is running with 8-bit character size, then the spiftest option `Char Size' should also be set to 8 bits. If you do not type within two minutes, this test will time-out. Terminate testing by pressing Control-C. After a short delay, the Status window updates the Pass Count. This test cannot be run concurrently with the 25-pin Loopback subtest. |
Printer |
Sends the entire ASCII character set to a parallel printer. You must attach a parallel printer to the parallel port on the Serial Parallel Controller patch panel. Observe the printer output to validate the test. |
Baud Rate |
Specifies the baud rate; choose 110, 300, 600, 1200, 2400, 4800, 9600, 19200, or 38400 baud. Note: The baud rate of 38400 can only be used if one port is tested at a time and the Internal Test is disabled. |
Char Size |
Indicates character length; choose 5, 6, 7, or 8 characters. |
Stop Bit |
Specifies the number of stop bits; choose 1 or 2 bits. |
Parity |
Specifies the selectable parity; choose none, odd or even. |
Flow Control |
Specifies the selectable flow control; choices are XOnOff, rtscts, or both. |
Data Type |
Specifies the selectable data type pattern; it can be 0x55555555 (0x55), 0xaaaaaaaa (0xaa), or random. |
Serial Port |
Specifies the serial port to be tested. The available ports are listed in the Configurations section at the top of the spiftest Options menu. |
You can also change the test options by modifying the /opt/SUNWvts/bin/.customtest file. See "Adding Your Own Tests" in .customtest in the SunVTS 3.0 User's Guide.