Changing Your Password

You can change your Kerberos password in two ways:

• With the usual UNIX passwd command. With SEAM installed, the Solaris passwd command also automatically prompts for a new Kerberos password.

  The advantage of using passwd instead of kpasswd is that you can set both passwords (UNIX and Kerberos) at the same time. However, you generally do not have to change both passwords with passwd. Often, you can change only your UNIX password and leave the Kerberos password untouched, or vice-versa.

  ---

  Note –

  The behavior of passwd depends on how the PAM module is configured. You might be required to change both passwords in some configurations. For some sites, the UNIX password must be changed, while other sites require the Kerberos password to change.

  ---

• With the kpasswd command. kpasswd is very similar to passwd. One difference is that kpasswd changes only Kerberos passwords. You must use passwd if you want to change your UNIX password.

  Another difference is that kpasswd can change a password for a Kerberos principal that is not a valid UNIX user. For example, david/admin is a Kerberos principal, but not an actual UNIX user, so you must use kpasswd instead of passwd.

After you change your password, it takes some time for the change to propagate through a system (especially over a large network). Depending on how your system is set up, this delay might take anywhere from a few minutes to an hour or more. If you need to get new Kerberos tickets shortly after you change your password, try the new password first. If the new password doesn't work, try again using the old password.

Kerberos V5 allows system administrators to set criteria about allowable passwords for each user. Such criteria is defined by the policy set for each user (or by a default policy). See Administering Policies for more on policies.

For example, suppose that user jennifer's policy (call it jenpol) mandates that passwords be at least eight letters long and include a mix of at least two kinds of characters. kpasswd will therefore reject an attempt to use “sloth” as a password.

% kpasswd
kpasswd: Changing password for jennifer@ENG.EXAMPLE.COM.
Old password:   <jennifer types her existing password>
kpasswd: jennifer@ENG.EXAMPLE.COM's password is controlled by
the policy jenpol
which requires a minimum of 8 characters from at least 2 classes 
(the five classes are lowercase, uppercase, numbers, punctuation,
and all other characters).
New password: <jennifer types  'sloth'>
New password (again):  <jennifer re-types 'sloth'>
kpasswd: New password is too short.
Please choose a password which is at least 4 characters long. 

Here, jennifer uses “slothrop49” as a password. “slothrop49” meets the criteria, because it is over eight letters long and contains two different kinds of characters (numbers and lowercase letters).

% kpasswd
kpasswd: Changing password for jennifer@ENG.EXAMPLE.COM.
Old password:  <jennifer types her existing password>
kpasswd: jennifer@ENG.EXAMPLE.COM's password is controlled by
the policy jenpol
which requires a minimum of 8 characters from at least 2 classes 
(the five classes are lowercase, uppercase, numbers, punctuation,
and all other characters).
New password:  <jennifer types  'slothrop49'>
New password (again):  <jennifer re-types 'slothrop49'>
Kerberos password changed.

Examples—Changing Your Password

In the following example, user david changes both his UNIX password and Kerberos password with passwd.

% passwd
	passwd:  Changing password for david
	Enter login (NIS+) password:         <type the current UNIX password>
	New password:                        <type the new UNIX password>
	Re-enter password:                   <confirm the new UNIX password>
	Old KRB5 password:                   <type the current Kerberos password>
	New KRB5 password:                   <type the new Kerberos password>
	Re-enter new KRB5 password:          <confirm the new Kerberos password>

In the preceding example passwd asks for both the UNIX password and the Kerberos password. However, if try_first_pass is set in the PAM module, the Kerberos password is automatically set to the UNIX password. This is the default configuration. In that case, user david must use kpasswd to set his Kerberos password to something else, as shown next.

This example shows user david changing only his Kerberos password with kpasswd.

% kpasswd
kpasswd: Changing password for david@ENG.EXAMPLE.COM.
Old password:           <type the current Kerberos password>
New password:           <type the new Kerberos password>
New password (again):   <confirm the new Kerberos password>
Kerberos password changed.
 

In this example, user david changes the password for the Kerberos principal david/admin (which is not a valid UNIX user). He must use kpasswd.

% kpasswd david/admin
kpasswd:  Changing password for david/admin.
Old password:		   	     <type the current Kerberos password>
New password:			       <type the new Kerberos password>
New password (again):	   <type the new Kerberos password>
Kerberos password changed.