admin(4) (man pages section 4: File Formats)

man pages section 4: File Formats

admin(4)

NAME

admin– installation defaults file

DESCRIPTION

admin is a generic name for an ASCII file that defines default installation actions by assigning values to installation parameters. For example, it allows administrators to define how to proceed when the package being installed already exists on the system.

/var/sadm/install/admin/default is the default admin file delivered with this release. The default file is not writable, so to assign values different from this file, create a new admin file. There are no naming restrictions for admin files. Name the file when installing a package with the -a option of pkgadd(1M). If the -a option is not used, the default admin file is used.

Each entry in the admin file is a line that establishes the value of a parameter in the following form:

param=value

All of the parameters listed below can be defined in an admin file, but it is not required to assign values to all of these. If a value is not assigned, pkgadd(1M) asks the installer how to proceed.

The valid parameters and their possible values are shown below except as noted. They can be specified in any order. Any of these parameters (except the mail and proxy parameters) can be assigned the value ask, which means that, when the parameter is reached during the installation sequence, the installer is notified and asked to supply instructions (see NOTES).

basedir

Indicates the base directory where relocatable packages are to be installed. If there is no basedir entry in the file, the installer will be prompted for a path name, as if the file contained the entry basedir=ask. This parameter can also be set to default (entry is basedir=default). In this instance, the package is installed into the base directory specified by the BASEDIR parameter in the pkginfo(4) file.

mail

Defines a list of users to whom mail should be sent following installation of a package. If the list is empty, no mail is sent. If the parameter is not present in the admin file, the default value of root is used. The ask value cannot be used with this parameter.

runlevel

Indicates resolution if the run level is not correct for the installation or removal of a package. Options are:

nocheck: Do not check for run level.
quit: Abort installation if run level is not met.

conflict

Specifies what to do if an installation expects to overwrite a previously installed file, thus creating a conflict between packages. Options are:

nocheck: Do not check for conflict; files in conflict will be overwritten.
quit: Abort installation if conflict is detected.
nochange: Override installation of conflicting files; they will not be installed.

setuid

Checks for executables which will have setuid or setgid bits enabled after installation. Options are:

nocheck: Do not check for setuid executables.
quit: Abort installation if setuid processes are detected.
nochange: Override installation of setuid processes; processes will be installed without setuid bits enabled.

action

Determines if action scripts provided by package developers contain possible security impact. Options are:

nocheck: Ignore security impact of action scripts.
quit: Abort installation if action scripts may have a negative security impact.

partial

Checks to see if a version of the package is already partially installed on the system. Options are:

nocheck: Do not check for a partially installed package.
quit: Abort installation if a partially installed package exists.

instance

Determines how to handle installation if a previous version of the package (including a partially installed instance) already exists. Options are:

quit: Exit without installing if an instance of the package already exists (does not overwrite existing packages).
overwrite: Overwrite an existing package if only one instance exists. If there is more than one instance, but only one has the same architecture, it overwrites that instance. Otherwise, the installer is prompted with existing instances and asked which to overwrite.
unique: Do not overwrite an existing instance of a package. Instead, a new instance of the package is created. The new instance will be assigned the next available instance identifier.

idepend

Controls resolution if other packages depend on the one to be installed. Options are:

nocheck: Do not check package dependencies.
quit: Abort installation if package dependencies are not met.

rdepend

Controls resolution if other packages depend on the one to be removed. Options are:

nocheck: Do not check package dependencies.
quit: Abort removal if package dependencies are not met.

space

Controls resolution if disk space requirements for package are not met. Options are:

nocheck: Do not check space requirements (installation fails if it runs out of space).
quit: Abort installation if space requirements are not met.

authentication

Controls resolution when a datastream package with signature is to be installed. Options are:

nocheck: Do not verify package signature. This also disables the use of the Online Certificate Status Protocol (OCSP) to validate the package's signing certificate.
quit: Abort installation if package signature cannot be verified.

networktimeout

Number of seconds to wait before giving up a network connection when downloading a package. This entry must be a positive integer. If not present, the default value of 60 is used.

networkretries

Number of times to retry a failed network connection when downloading a package. This entry must be a positive integer. If not present, the default value of 5 is used.

keystore

Location of trusted certificates used when downloading packages over SSL and when verifying signatures on packages. This is the base directory of the certificate location for trusted certificates used when validating digital signatures on packages. For example, if this setting is /var/sadm/security, then pkgadd will use /var/sadm/security/pkgadd/truststore, then /var/sadm/security/truststore when searching for trusted certificates. See KEYSTORE LOCATIONS and KEYSTORE AND CERTIFICATE FORMATS in pkgadd(1M) for details on certificate store format and usage.

proxy

The default proxy to use when installing packages from the network. Currently, only HTTP or HTTPS proxies are supported. If this field is blank or nonexistent, then no proxy will be used.

EXAMPLES

Example 1 Default `admin` File

The default admin file, named default, is shipped with user-, group-, and world-read privileges (444). Its contents are as follows:

mail=
instance=unique                                                    
partial=ask                                                        
runlevel=ask
idepend=ask
rdepend=ask
space=ask
setuid=ask
conflict=ask
action=ask
basedir=default
authentication=quit
networktimeout=10
networkretries=3
keystore=/var/sadm/security
proxy=

Example 2 Sample `admin` file.

Below is a sample admin file.

basedir=default
runlevel=quit
conflict=quit
setuid=quit
action=quit
partial=quit
instance=unique
idepend=quit
rdepend=quit
space=quit
authentication=quit
networktimeout=10
networkretries=5
keystore=/opt/certs
proxy=syrinx.eng.sun.com:8080

FILES

The default admin file is consulted during package installation when no other admin file is specified.

/var/sadm/install/admin/default: default admin file

ATTRIBUTES

See attributes(5) for descriptions of the following attributes:

ATTRIBUTE TYPE	ATTRIBUTE VALUE
Availability	SUNWpkgcmdsr
Interface Stability	Evolving

NOTES

The value ask should not be defined in an admin file that will be used for non-interactive installation (because, by definition, there is no installer interaction). Doing so causes installation to fail at the point when input is needed.

SunOS 5.9 Last Revised 2 Sep 2003