有关群集专用传输要求的信息,请参见《Sun Cluster 3.1 - 3.2 Hardware Administration Manual for Solaris OS》中的“Interconnect Requirements and Restrictions”。
您还可以使用 Sun Cluster Manager GUI 来完成此过程。有关详细信息,请参见 Sun Cluster Manager 联机帮助。
phys-schost# 提示符表示全局群集提示符。此操作过程适用于全局群集。
此过程提供了 Sun Cluster 命令的长格式。此外,大多数命令还有简短格式。这些命令除了名称长短的不同以外,其功能都是相同的。有关命令及其简短格式的列表,请参见附录 B。
确保安装了群集传输电缆(电缆本身)。
有关安装群集传输电缆的过程,请参见《Sun Cluster 3.1 - 3.2 Hardware Administration Manual for Solaris OS》。
成为群集中任一节点上的超级用户。
启动 clsetup 实用程序。
# clsetup |
显示“Main Menu”。
键入与显示群集互连菜单的选项相对应的编号。
如果配置所使用的是 SCI 适配器,则在该过程的 “添加” 操作中提示适配器连接(端口名)时,不要接受默认设置。而是应提供在 Dolphin 交换机上所找到的端口名(0、1、2、或 3),节点通过电缆以物理方式与之连接。
键入与添加传输电缆的选项相对应的编号。
按说明进行操作,并键入请求的信息。
键入与向节点添加传输适配器的选项相对应的编号。
按说明进行操作,并键入请求的信息。
如果打算将以下任何适配器用于群集互联,请在各群集节点上的 /etc/system 文件中添加相关条目。此条目在下次引导系统后生效。
适配器 |
条目 |
---|---|
ce |
set ce:ce_taskq_disable=1 |
ipge |
set ipge:ipge_taskq_disable=1 |
ixge |
set ixge:ixge_taskq_disable=1 |
键入与添加传输交换机的选项相对应的编号。
按说明进行操作,并键入请求的信息。
检验是否添加了群集传输电缆、传输适配器或传输交换机。
# clinterconnect show node:adapter,adapternode # clinterconnect show node:adapter # clinterconnect show node:switch |
以下示例说明了如何使用 clsetup 实用程序向节点添加传输电缆、传输适配器或传输交换机。
[Ensure that the physical cable is installed.] [Start the clsetup utility:] # clsetup [Select Cluster interconnect] [Select either Add a transport cable, Add a transport adapter to a node, or Add a transport switch.} [Answer the questions when prompted.] [You Will Need: ] [Information: Example:[ node names phys-schost-1 adapter names qfe2 switch names hub2 transport type dlpi [Verify that the clinterconnect command completed successfully:]Command completed successfully. Quit the clsetup Cluster Interconnect Menu and Main Menu. [Verify that the cable, adapter, and switch are added:] # clinterconnect show phys-schost-1:qfe2,hub2 ===Transport Cables === Transport Cable: phys-schost-1:qfe2@0,hub2 Endpoint1: phys-schost-2:qfe0@0 Endpoint2: ethernet-1@2 ???? Should this be hub2? State: Enabled # clinterconnect show phys-schost-1:qfe2 === Transport Adepters for qfe2 Transport Adapter: qfe2 Adapter State: Enabled Adapter Transport Type: dlpi Adapter Property (device_name): ce Adapter Property (device_instance): 0 Adapter Property (lazy_free): 1 Adapter Property (dlpi_heartbeat_timeout): 10000 Adpater Property (dlpi_heartbeat_quantum): 1000 Adapter Property (nw_bandwidth): 80 Adapter Property (bandwidth): 70 Adapter Property (ip_address): 172.16.0.129 Adapter Property (netmask): 255.255.255.128 Adapter Port Names: 0 Adapter Port STate (0): Enabled # clinterconnect show phys-schost-1:hub2 === Transport Switches === Transport Switch: hub2 Switch State: Enabled Switch Type: switch Switch Port Names: 1 2 Switch Port State(1): Enabled Switch Port State(2): Enabled |
要检查群集传输电缆的互连状态,请参见如何检查群集互连的状态。