About This Documentation (PDF and HTML)
Download Server System Tools and Drivers
Hardware Installation and Product Notes
Sun Fire X2270 M2 Server Installation Guide
Installation Overview and Preparation
Installing the Server Into a Rack With Optional Slide Rails
Communicating With the ILOM and the System Console
Configuring the Factory--Installed Oracle Solaris 10 Operating System
Powering On and Powering Off the Server
Sun Fire X2270 M2 Server Product Notes
Oracle Solaris Operating System
Planning the Oracle Solaris Operating System Installation
Installing Oracle Solaris 10 OS
Introduction to Linux Installation
Preliminary Tasks Before Installing an OS
Installing Oracle Enterprise Linux
Installing SUSE Linux Enterprise Server
Installing Red Hat Enterprise Linux
Booting From OS Distribution Media
Configuring a Linux Server to Support PXE Installation
Identifying Logical and Physical Network Interface Names for Linux OS Configuration
Planning the Operating System Installation
Installing Windows Server 2008 Operating System
Incorporating Sun Fire Drivers Into a WIM Image
Configuring RAID Controller in the BIOS Setup Utility
Sun Fire X2270 M2 Server Installation Guide for ESX Software
Preparing to Install VMware ESX 4.0 and ESXi 4.0
Administration, Diagnostics, and Service
Overview of the ILOM Supplement
Supported ILOM 3.0 Feature Set
Sun Fire X2270 M2 Server Platform-Specific Features
Communicating With the ILOM and the System Console
Server Back Panel LEDs and Ports
About ILOM SP IP Addresses and the ILOM Interfaces
How to Get the SP IP Address Using the BIOS Setup Utility
How to Get the SP IP Address Using a Serial Connection and the CLI
How to Connect to the Command-Line Interface Using SSH
How to Connect to the ILOM Web Interface
Connecting to the System Console
How to Connect to the Server Locally (Physical Console)
How to Connect Remotely Using the ILOM Web Interface
How to Connect to the Serial Console Using the ILOM CLI
ILOM Platform Features for the Sun Fire X2270 M2 Server
Switching Serial Port Output Between SP and Host Console
How to Switch Serial Port Output Between the SP and the Host Console Using the Web Interface
How to Switch Serial Port Output Between the SP and the Host Console Using the CLI
Special Considerations for Sideband Management
How to Configure Sideband Management Using the Web Interface
How to Configure Sideband Management Using the CLI
Running IPMITool from the Host
Updating ILOM Firmware Using the IPMIflash Utility
Temperature and Voltage Readings
How to View the Sensors From the System BIOS
BIOS System Event Log Sensor Error List
Using ILOM to Monitor the Host
Determining Current Firmware Versions
How to Determine the ILOM and BIOS Firmware Versions Using the Web Interface
Preparing for a Firmware Update
How to Plan the Firmware Update
How to Download Firmware Updates
Updating the ILOM and System BIOS
How to Update the ILOM and System BIOS Using the Web Interface
How to Update the ILOM and System BIOS Using the Command-Line Interface
Introduction to Diagnostic Tools
U-Boot Diagnostic Startup Tests
Accessing the Pc-Check Diagnostics Utility on the Tools and Drivers CD/DVD
Sun Fire X2270 M2 Server Service Manual Organization
Sun Fire X2270 M2 Server Overview
Maintaining the Sun Fire X2270 M2 Server
Sun Fire X2270 M2 Server Service Procedures and Information
Use this procedure to establish a serial connection to the ILOM SP so that you can perform initial configuration of ILOM.
Before You Begin
Perform the hardware setup as described in the Sun Fire X2270 M2 Server Installation Guide.
Apply standby power to the server by connecting AC power to the system power supply. See Server Back Panel LEDs and Ports for the location of the power connectors.
Verify that your terminal, laptop, or terminal server is operational.
8, N, 1 (eight data bits, no parity, one stop bit).
9600 baud.
Disable hardware flow control (CTS/RTS).
Disable software flow control (XON/XOFF).
See Server Back Panel LEDs and Ports for the location of the RJ-45 SERIAL MGT port.
The SP eventually displays a login prompt, such as the following example:
SUNSPproduct_serial_numberlogin:
where
The string SUNSP is the same for all SPs.
product_serial_number is the product serial number by default. This value can also be the host name, which is assigned by the user or the DHCP server.
Note - You must have administrator privileges for this task.
The default user name is root and default password is changeme.
The CLI prompt appears:
->
Note - For detailed instructions on CLI commands, refer to Oracle Integrated Lights Out Manager 3.0 CLI Procedures Guide.
cd /SP/console
-> start
Note - You can switch back to the SP CLI from the serial console by pressing the Esc ( key sequence.