Non-Interactive and Interactive Modes

You can use the ndd utility in two modes:

• Non-interactive

• Interactive

In non-interactive mode, you invoke the utility to execute a specific command. Once the command is executed, you exit the utility. In interactive mode, you can use the utility to get or set more than one parameter value. (Refer to the ndd (1M) man page for more information.)

Using the ndd Utility in Non-Interactive Mode

1. To modify a parameter value, use the -set option.

   If you invoke the ndd utility with the -set option, the utility passes value, which must be specified down to the named /dev/eri driver instance, and assigns it to the parameter:

   % ndd -set /dev/eri parameter value

1. To display the value of a parameter, specify the parameter name (and omit the value).

   When you omit the -set option, a query operation is assumed and the utility queries the named driver instance, retrieves the value associated with the specified parameter, and prints it:

   % ndd /dev/eri parameter

Using the ndd Utility in Interactive Mode

1. To modify a parameter value in interactive mode, specify ndd eri, as shown below.

   The ndd utility then prompts you for the name of the parameter:

   % ndd /dev/eri name to get/set? (Enter the parameter name or ? to view all parameters)

After you enter the parameter name, the ndd utility prompts you for the parameter value (see Table 3-1 through Table 3-9 for parameter descriptions).

1. To list all the parameters supported by the eri driver, type:

   % ndd /dev/eri \?

   (See Table 3-1 through Table 3-9 for parameter descriptions.)

   ---

   Example 4-1 Example of Listing All Parameters Supported by the eri Driver

   
   

   example# ndd /dev/eri \? ? (read only) transceiver_inuse (read only) link_status (read only) link_speed (read only) link_mode (read only) ipg1 (read and write) ipg2 (read and write) use_int_xcvr (read and write) pace_size (read and write) adv_autoneg_cap (read and write) adv_100fdx_cap (read and write) adv_100hdx_cap (read and write) adv_10fdx_cap (read and write) adv_10hdx_cap (read and write) autoneg_cap (read only) 100T4_cap (read only) 100fdx_cap (read only) 100hdx_cap (read only) 10fdx_cap (read only) 10hdx_cap (read only) lp_autoneg_cap (read only) lp_100fdx_cap (read only) lp_100hdx_cap (read only) lp_10fdx_cap (read only) lp_10hdx_cap (read only) instance (read and write) lance_mode (read and write) ipg0 (read and write) example#

   ---

Setting Forced Mode

The procedure that follows describes how to set forced mode (not capable of auto-negotiation).

To Select a Transceiver Capability and Set Forced Mode

1. Select one of the following capabilities: adv_100fdx_cap, adv_100hdx_cap, adv_10fdx_cap, or adv_10hdx_cap, and set its value to 1.

   If you select more than one of the local transceiver capabilities, the driver selects the one that is highest in the priority order.

2. Set the local transceiver capabilities advertised by the hardware to forced mode = 0, which is not capable of auto-negotiation: adv_autoneg_cap 0

   Use the ndd utility as described in "Using the ndd Utility in Interactive Mode" in this chapter.

Auto-Negotiation Mode

To Set the Mode to Auto-Negotiation

1. Select at least one of the four capabilities (adv_100fdx_cap, adv_100hdx_cap, adv_10fdx_cap, adv_10hdx_cap) that you want to advertise to the remote system, and set its value to 1.

2. Set the local transceiver capabilities advertised by the hardware to 1, the auto-negotiation setting: adv_autoneg_cap 1

   Use the ndd utility as described in "Using the ndd Utility in Interactive Mode" in this chapter.