C H A P T E R 7 |
Sun Enterprise 10000 Release Notes |
This chapter contains the release notes for the following features on the Sun Enterprise 10000 server: SSP 3.5, dynamic reconfiguration (DR), InterDomain Networks (IDNs), and the Solaris operating environment on Sun Enterprise 10000 domains.
For an overview of SSP 3.5 functionality, refer to the SSP 3.5 Installation Guide and Release Notes. The list of open bugs in that document is accurate as of the date of its publication. Sun suggests you check the SunSolve website on a regular basis for the SSP patches available for SSP 3.5:
If you need to install SSP software patches, be sure to install the patches on both the main and spare SSP, as explained in the SSP 3.5 Installation Guide and Release Notes.
Release notes and other technical information in this section apply only to dynamic reconfiguration (DR) software on a domain of the Sun Enterprise 10000 system running Solaris 8 2/04 software.
This section contains general issues that involve DR on the Sun Enterprise 10000 server. You should read this section before you attempt to install or configure DR.
For Solaris 8 2/04, DR does not automatically unbind user processes from CPUs that are being detached. Users must perform this operation themselves before initiating a detach sequence. The drain operation fails if CPUs are found with bound processes.
A panic can occur under certain circumstances when the /dev/openprom interface accesses the PROM device tree after a DR disconnect. The openprom driver caches node information that can become invalid after a DR disconnect. As a result, OpenBoot PROM can be passed a bad node address.
Workaround: To minimize the possibility of encountering this situation, discontinue using applications, such as prtconf, that use the /dev/openprom interface during or immediately before or after a DR disconnect operation. Note that picld(1M) uses the /dev/openprom driver.
After the qfe driver is suspended during a DR operation quiesce of the Solaris operating environment, the qfe driver might not resume correctly. This results in a loss of network connectivity. If this condition occurs, the domain will still be accessible through the network console from the SSP.
Workaround: Reset the qfe device by executing the following sequence of commands from the network console:
Where qfe_device is the affected qfe device, e.g. qfe0.
If you upgrade or perform a fresh install of the Solaris operating environment on a domain before you upgrade the SSP to SSP 3.5, the domain will not be properly configured for DR 3.0.
Workaround: Run the following command as superuser on the domain, after the SSP has been upgraded to SSP 3.5. This workaround is not necessary until DR 3.0 is enabled on the domain.
For a domain to become part of an IDN, all boards in that domain that have active memory must have at least one active CPU.
This section contains general issues, known bugs, patches, and notes about the Solaris 8 2/04 operating environment on the Sun Enterprise 10000 server.
Alternate Pathing (AP), dynamic reconfiguration (DR), and InterDomain Networks are supported in the Solaris 8 2/04 release.
If you are upgrading the operating environment from Solaris 2.6 to Solaris 8 2/04 and you used the partition layout suggested in the SMCC Hardware Platform Guide Solaris 2.6, the partitions might not be large enough for the upgrade. For instance, the /usr partition must be at least 653 megabytes. If /usr is smaller than the size needed to perform the upgrade, suninstall uses the Dynamic Space Reallocation (DSR) mode to reallocate the space of the disk partitions.
DSR may calculate a partition layout which is not acceptable for some systems. For instance, DSR may select partitions that appear to DSR as being unused (non-UFS partitions which may contain raw data or other types of file systems). If DSR selects a used partition, data loss may occur. Therefore, you must know the current status of the partitions DSR wants to use before you allow DSR to continue with the reallocation of the disk partitions.
After DSR presents an acceptable layout and you choose to proceed with the reallocation, DSR adjusts the affected file systems, and the upgrade continues. However, if you cannot constrain the layout so that it is acceptable for your needs, then you may need to manually repartition the boot device, or you may have to perform a fresh install.
Before you perform the boot net command from the OpenBoot PROM prompt (ok), you must verify that the local-mac-address? variable is set to false, which is the factory default. If the variable is set to true, you must ensure that this value is an appropriate local configuration.
Caution - If local-mac-address? is set to true, it may prevent the domain from successfully booting over the network. |
In a netcon(1M) window, you can use the following command at the OpenBoot PROM prompt to display the values of the OpenBoot PROM variables:
If the variable is set to true, use the setenv command to set it to false.
Sun Enterprise 10000 systems with 64 Gbytes of memory cannot boot the Solaris 8
2/04 operating environment in 32-bit mode.
Copyright © 2003, Sun Microsystems, Inc. All rights reserved.