Sun OTP Plan Settings Description

The following list describes each of the Sun OTP plan settings that are used by the Sun OTP installation. These settings need to be specified in the Setup Configuration plan during the installation.

• mediaDirectory

  The fully-qualified path name to the Sun Open Telecommunications Platform installation source directory.

• clusterName

  Name of the cluster. The length of the cluster name has to be less than 19 characters.

• mgmtHost

  Logical host name used by the Sun OTP system management service. The logical host name must correspond to the management logical IP address.

• mgmtIP

  Logical IP address used by the Sun OTP system management service. The IP address must be an unused IP address.

• jesHAHost

  Host name for Sun OTP security service shared address.

• jesHANodeList

  List of host names and respective zones on which the Sun OTP security service is running.

  For deployment without zones, use the following syntax:

  h1_hostName+h2_hostName...

  For deployment with zones, use the following syntax:

  h1_hostName:h1_zoneName+h2_hostName:h2_zoneName...

• mmrHostList

  List of host names or zone host names between which the master-to-master replication of data between directory server instances are provided.

  For deployment without zones, use the following syntax:

  h1_hostName+h2_hostName...

  For deployment with zones, use the following syntax:

  h1_zoneHostname+h2_zoneHostname...

• applyAllPatches

  Specifies whether all patches or only mandatory patches are to be installed. The default value is yes, which specifies that all patches must be installed. To install only mandatory patches, specify no.

• spsRAConnectionType

  Specifies the connection type between Sun OTP application provisioning service master server and the remote agent. The values can be SSH or RAW. The default and recommended value is SSH.

  This variable must match the connection type that is provided while setting up the Sun OTP provisioning server and installing the remote agent.

• hostName

  The host name of the Sun OTP host. The length of the host name has to be less than 19 characters.

• hostType

  Type of host in the cluster. The possible values are single, first, and additional. For stand-alone host, the host type is single. For clustered configuration, the host type is first for the first host in the cluster and additional for the remaining hosts in the cluster.

• sponsorNode

  The name of the first Sun OTP host in a clustered Sun OTP system. The first Sun OTP host is the sponsoring node for all the additional Sun OTP hosts. This setting is required when installing the Sun Open Telecommunications Platform on two or more hosts.

  This variable is required only for hosts of host type additional.

• autoConfigureIPMP

  Setting to determine whether IPMP is configured automatically. The Possible values are yes and no. The default value is no.

  You should configure all physical interfaces of a multipathing group with a test IP address. Test addresses are required to detect failures.

  If you set autoConfigureIPMP=yes, then you must also specify the following values:

  • secondaryInterface

    Interface used as the failover interface if a fault is detected on the primary interface.

  • secondaryIP

    IP address of the secondary interface that is used for failover. This variable is the same as testIPAddress but used for the secondary interface.

  • testIPAddress

    An unused IP address that is to be assigned as a routable, no-failover, and deprecated test IP address to the adapter. IP network multipathing uses test addresses to detect network path failures, switch port faults, and partial network equipment outages.

• privateInterface1

  The first private network interface on Sun OTP host. Required when hostType is first or additional.

• privateInterface2

  The second private network interface on Sun OTP host. Required when _hostType is first or additional.

• transportTypeInterface1

  The transport type of the first private interconnect adapter on Sun OTP host. The required value is dlpi. Do not change the value.

  For more information, refer to dlpi(7P) man page.

• transportTypeInterface2

  The transport type of the second private interconnect adapter on Sun OTP host. The required value is dlpi. Do not change the value.

  For more information, refer to dlpi(7P) man page.

• nodeAuthentication

  Setting to establish the authentication policies for hosts. The possible values are sys and des. The default value is sys.

• quorumAutoConfiguration

  ---

  Note –

  Quorum automatic configuration applies only to two-host clusters.

  ---

  Quorum automatic configuration provides an option to enable or disable automatic configuration of the quorum device in a two-host only clustered Sun OTP system.

  The possible values are yes and no. The default value is yes.

  ---

  Note –

  If this value is set to no, a manual administrative procedure is required to configure the quorum disk in a two-host clustered Sun OTP system. The cluster must be manually reset from the install mode to the normal mode. For details about how to configure quorum disks, refer to the scconf command documentation in scconf(1M) man page.

  ---

• rootDisk

  Name of the root disk that is used to store the Solaris Volume Manager (SVM) database.

• diskSlice

  The disk slice where the Solaris Volume Manager (SVM) state database replicas are stored. The default value is s7. Refer to Solaris Volume Manager Administration Guide for more information.

• zoneName

  Name of the non-global zone for the Sun OTP security service. This variable has to be filled or remain empty for deployment with or without zones respectively.

• zoneInterface

  Network interface to be used for the non-global zone, typically the primary interface of the host.

• zoneIPAddress

  IP address of the non-global zone.

• zoneHostName

  Host name of the non-global zone corresponding to zoneIPAddress.

• zonePath

  Path to store the non-global zone.

• zoneMask

  Network mask of the non-global zone.

• zoneDefaultRoute

  Network default route of the non-global zone. zoneDefaultRoute must be on the same logical subnet as zoneIPAddress.

• managementInterface

  Name of the network interface used for Sun OTP system management services. The name of the interface depends on the platform type.

• provisioningInterface

  Name of the network interface used for Sun OTP application provisioning services. The name of the interface depends on the platform type.

• domainName

  Domain name used by the Sun OTP security service.

• ssoCookieDomain

  Domain name for the Web SSO cookies. The Domain name must start with a dot (.) symbol.